This study was performed to investigate the concentrations of PM($PM_{10}$, $PM_{2.5}$, $PM_{1}$) and it's affecting factors in the subway from line 1 to line 8 in Seoul metropolitan area, from Sep. 1 to 30, 2005. PM concentrations were measured at the entrances and centers in subway passenger cabins by a light scattering equipment. And the affecting factors to PM were estimated based on the number of passenger, door open and close and running area etc. The geometric means of $PM_{10}$, $PM_{2.5}$ and $PM_{1}$ concentration in Seoul subway passenger cabins were $214{\mu}g/m^3$, $86.6{\mu}g/m^3$ and $27.0{\mu}g/m^3$, respectively. These mean concentrations in subway carriage were higher when it ran on an underground track than on a ground track. And running time(7AM-9AM, 11AM-13PM, 6PM-8PM) significantly influenced to the concentrations of $PM_{10}$, $PM_{2.5}$ and $PM_{1}$. Daily profile of $PM_{10}$ and $PM_{2.5}$, $PM_{1}$ expressed as an 10 minutes average, showed similar variation pattern over day period. In correlation analysis, significant relations among $PM_{10}$, $PM_{2.5}$ and $PM_{1}$ were detected(p〈0.01). In particular, correlation coefficient between $PM_{10}$and $PM_{1}$ was highly significant(r=0.94). Further study is needed to identity the sources of PM in subway cabins and to compare pollutants concentration among subway lines.
승용차의 실내공간은 다수의 부품들로 구성되어 있으며, 그들 중 인스트루먼트 패널은 그 디자인에 따라 실내공간의 활용과 이 , 그리고 운전자의 조작성과 실내공간의 안전도까지도 좌우하는 중요한 부품이다. 초기 자동차에서의 인스트루먼트 패널은 엔진실과 실내공간을 구분 짓는 벽체에 운전에 필요한 엔진의 상태를 알리기 위한 계기를 부탁하는 개념에 출발하였다. 그러므로 운전석의 좌우 위치에 관게없이 패널 중앙부에 계기류를 장착하는 개념이 주류를 이루었다. 차량의 기능 향상과 장착품의 증가로 운전석 중심의 독립된 계기판과 충격 흡수제를 부탁한 구조가 등장하였으며, 이것은 오늘날의 다양한 형태의 계기판의 출발점이 되었다. 최근의 승용차의 계기판은 차량 안전 법구의 강화와 신공법의 개발, 그리고 운전 편의성 향상 등을 위하여 중앙부에 클러스터를 장착한 유형이 몇몇 차종에서 다시 등장하고 있다. 이러한 승용차 인스트루먼트 패널의 디자인 특징과 기능성 특성들을 분석하면 다음과 같은 결과를 얻을수 있다. -전방 시인성의 향상을 위한 I/P 전체의 부피 감소 -강화된 충돌 규제를 위한 보조 장치와 완충 구조의 설정 -운전 편의성과 초점 거리 차이 감소를 통한 안전성 향상을 위한 중앙부 클러스터 장착 유형의 재등장유형의 재등장
This study had the aim of characteristics of $PM_{10}$ in subway cabins. $PM_{10}$ was measured by times of day (rush and non rush hours) and seasons with real time $PM_{10}$ sampler on the subway cabins of line 7. Filter samples were collected for evaluation of their elemental composition as well as identification of major sources of $PM_{10}$ using a receptor model, PMF. $PM_{10}$ concentration were the highest in the winter season both in the rush and non rush hours at 152.8 ${\mu}g/m^3$, 90.2 ${\mu}g/m^3$ respectively. The $PM_{10}$ concentrations in rush hour were 30% higher compared to non rush hours. Based on the chemical information, the composition rare of inorganic elements was 52.5%, anions were 10.2% and others were 37.3%. Fe was the most abundant element and significantly correlated (p.0.01) with Mn (r=0.97), Ti (r=0.91), Cr (r=0.88), Ni (r=0.89) and Cu (r=0.88). Characterized $PM_{10}$ sources by PMF in the cabin were soil and road dust related sources (27.2%), railroad related sources (47.5%), secondary nitrate sources (16.2%) and a Cl-factor mixed with a secondary sulfate source (9.1%).
1990년대는 유압굴삭기의 전통적 조형이 새롭게 모색 및 재해석되는 시기로 판단되었으며, 이는 2가지 방향으로 정리될 수 있다. 하나는 유압굴삭기의 전통적 이미지에 관한 부정적 해석에서 기인한 '탈(post-heavy equipment)중기적' 경향이며, 다른 하나는 고유성 유지와 개선이라는 긍정적 해석에서 기인한 '후기(late-)중기적' 경향이다. 이는 동일한 현상을 다양하게 바라볼 수 있는 패러다임과 관련하는 것으로 사료된다. 이 시기에 개발 및 시판된 8개 연구대상 모델 중 유압굴삭기의 조형 경향은, 일본 색채디자인연구소에서 개발한 이미지스케일 3상한에서 2상한으로 변화였으며, 예외적으로 코벨코는 1상한까지 이동하는 경향이 있었다. 이는 탈중기적 이미지를 디자인 전략으로 채택하고 있는 코벨코만의 경우였다. 아울러, 인적(入的)공간으로서의 캐빈의 변화는 장비 전체의 변화에서보다 좀더 1상한으로 이동하고 있는데, 이는 물적(物的)공간과 시각적 차별화를 위한 것으로 사료되었다.
본 논문에서는 선박 내에서 Bluetooth 기반의 Beacon을 활용하여 탑승객 및 선원들의 위치를 추적하는 시스템에 대하여 제안하였다. 추적된 탑승객들의 위치는 선박 침몰과 같은 치명적인 위급상황 발생시 구조대가 효율적으로 신속하게 승객들을 구조하는 데 활용될 수 있으며, 수집된 데이터들은 사용자들의 동선 패턴을 파악하여 부가적으로 활용될 수 있다. 이 논문에서 제안된 시스템은, 선실마다 AP(Access Point)라고 불리는 MAC 데이터 수집 장치를 설치하고, 설치된 AP에서는 탑승자들에게 제공된 Tag의 정보를 검색하고 수집한다. Tag는 개인 정보 보호를 위하여 고유의 MAC Address만을 가지며, 별도의 사용자 정보는 수집하지 않는다. 모든 데이터 통신은 MAC Address만을 송 수신하도록 하여 익명성을 보장하였다.
선박에서 선내 소음이 문제로 인식되기 시작한 시기는 1970년대 초반 유럽에서 선박소음규제를 명문화하기 시작하였다. 이후 1982년 국제해사기구(IMO)에서 "International Code on Noise Levels on Board Ships"가 채택되어 오늘날에는 거의 모든 신조 선박에 대하여 해당하는 조항의 적용이 명문화되었다. 특히, 대형의 디젤기관과 다수의 보조기계가 동시에 운전되어지는 기관실 내부는 크고 복잡한 소음이 발생하는 환경으로 되어지고, 이러한 환경에서 작업하는 작업자는 소음성난청으로 되기 쉽다. 최근에는 각 나라별로 직업상의 난청으로부터 작업자를 보호할 목적으로 허용소음 폭로 시간을 법적으로 규제하고 있다. 우리나라에서는 근로기준법에서 정의하고 있지만 선박의 기관실과같이 특수한 조건에 대해서 국제해사기구의 규정에 따르고 있다. 본 논문에서는 국내 서남 연안을 정기적으로 운항하고 있는 화객선에 대한 소음의 정도를 조사하였다
Purpose: Year of 2020, COVID-19 has been changing the people's everyday life to ways never been thought of before all over the world. The IT and electronic industry, the methods of supplying goods and services have been changed from contact to un-tact environments based on un-tact systems very rapidly. COVID-19 has been striking the tourism and the travel industry, especially the airline and hotel industry of which services are provided by human. For the passenger service of airliner, automation has been propelled and un-tact style of service has become mainstreams except cabin service since 2000's. For passenger transportation, due to traffic regulations and exclusions etc., switching to new ways is not easy. However, under the new environment made by COVID-19, kiosk check-in, web check-in and mobile check-in has become more important. In this study, the characteristics of airline customers using mobile goods are investigated to find ways to raise the rate of utilizing mobile check-in and to increase the efficiency of boarding process. Research design, data, and methodology: Considering the COVID-19 environment, survey was done by online research company. The research model is designed to integrate the user characteristics and usage/purchase motive and technology acceptance theory. Especially considering infectious diseases prevention, concern of safety is adopted as one of the usage motive variable. Results: Extraversion or conscientiousness characteristics prefers counter check-in(contact service), while openness characteristics prefers mobile check-in(un-tact service). Concern of safety for infectious disease shows strong non-preference on counter check-in. Conclusions: Regarding service type regardless of type of the industry, automation and un-tact have been mainstreams due to high costs of labor, efficiency and standardization issue, etc., and COVID-19 has given impetus to them. For airliner, un-tact service including boarding process service has been more and more important. To raise the rate of un-tact service use, the characteristics of the user should be analyzed first. The study results indicate that for extraversion or conscientiousness, some kinds of methods to induce them to use un-tact service more are needed.
The new high speed combi train prototype project was developed which named HSB. It runs over the speed of 330km/h. As the speed of the train exceeds over 300km/h, due to pressure change in tunnel, aerodynamic problems such as sudden drag increase, severe acoustic noise, passenger discomfort and tunnel pressure sonic boom were occurred. This aerodynamic characteristics in tunnel should be reviewed in early design state to enhance the performance and driving quality of new high speed train. In this paper, the aerodynamic characteristics in tunnel for HSB such as pressure waves in tunnel, a rate of pressure change in cabin and micro pressure wave that cause sonic boom outside tunnel are analyzed by 2D axisymmetric CFD simulations. The results are also compared with the value for ordinary high speed train like the KTX-Sancheon. It is helpful how to design the configuration of HSB train. Finally it shows that the HSB train was well designed in tunnel condition because all values fulfill the criterions on UIC code and Korean national regulations.
A general procedure for the design sensitivity analysis of structural dynamic problems has been presented in frame of the FRF-based substructuring formulation. For a system response function, the proposed method gives a parametric design sensitivity formula in terms of the partial derivatives of the connection element properties and the transfer matrix of the subsystems. The derived design sensitivity formula is applied to an engine mount system. An interior noise problem in the passenger car is analyzed using the FRF-based substructuring method and the proposed formulation is adopted to study the response variations with respect to the dynamic characteristics of the engine mounts and the bushes. To obtain the FRFs, a finite element model is built for the engine mount structures, and test data is used for the trimmed body including cabin cavity. The comparison of sensitivities derived by the proposed method and the finite difference method shows that the proposed method is efficient and accurate. The proposed sensitivity analysis method indicates effectively the most sensitive location to the interior noise among the engine mounts and the bushes.
The interior sound pressure level of the Korean high-speed train(KHST) is predicted by geometrical acoustic method. For the Purpose of assuring the prediction of Interior noise of KHST by the geometrical acoustic scheme, calculated sound level values of the Korean train express(KTX) by Identical geometrical method are compared with measured values of KTX prototype vehicle by experiment. Contribution of individual sound source of KHST vehicle Into the interior response positions is calculated and sound sources are classified in influential order. Hence, it is reasonable approach to reduce sound power of most contributing noise source first. Sensitivity of the interior response position's sound pressure level (SPL) with respect to train wall sections' transmission loss are carried on and acoustically sensitive spot is identified, for example window area for passenger cabin case. Those contribution and sensitivity analysis results are suggested to design quieter train efficiently.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.