• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1997.12a
• /
• pp.255-262
• /
• 1997

A low-cost and precise metering device, which is suitable to automatic mixing of nutrient-solution for hydroponic culture, was developed for small-scale growers. The metering device was composed of three parts those were supply pumps, metering cylinders and venturi tube. Those parts were controlled by personal computer with time-based odoff control method. To verify the performance of the developed metering device, the relationship between operating time and discharge was examined and the accuracy of the developed metering device was compared with commercial metering pumps. The results of this study are as follows. 1. The correlation coefficient between the flow rate and operating time was 0.9999, and the linear regression equation computed was y=21.759x, where y is the discharge(g) and x is the operating time(s). 2. The developed device has greater accuracy than commercial metering pumps in terms of the full-scale error. Calculated errors for the developed metering device and two commercial pump were $\pm$0.3 %, $\pm$2.45 % and $\pm$1.38 % respectively. 3. Above results show developed metering device is a useful tool for nutrient-solution control system.

• KCID journal
• /
• v.21 no.1
• /
• pp.109-117
• /
• 2014

Multi water-loop system is the efficient customer centered facilities of water supply by utilizing the multi water resources. Multi water-loop system is divided into various types. The system is classified potable and non-potable type. Mostly, the potable type utilizes surface water and ground water. However, the non-potable type utilize the multi water resources, such as rain water, sea water, reclaimed water, etc. Selective intake is possible when characteristics of region, physiographic condition and purpose of use are considered. For instance, downtown type, new-city type, agriculture type, island type are available. For development and application of these multi water-loop system, standardization is needed. For standardization, several methods are given; design principles, selection and composition method of multi water-loop system structure, BIM/GIS application method, safety inspection method. Consequently, a road map of design standardization method can be established. In this road map, there are three parts for the standardization of multi water-loop system. Three parts are the considerations, base material and ways of standardization. Design standardization become close when this road map followed by someone who plan the multi water-loop system. In this way, loop system's development is more efficient and economic. In hereafter research, each type's characteristic will be analysed and standardization methods can be established.

• Asian-Australasian Journal of Animal Sciences
• /
• v.25 no.1
• /
• pp.143-150
• /
• 2012

Competition in global pork markets has increased as trade barriers have opened as a result of free trade agreements. Japanese prefer both loin and Boston butt, while Chinese prefer pork offal. Frozen pork has increased in terms of imports into China. Japanese consumers consider pork meat origin along with pork price when making purchase decisions. While the Chinese prefer a strong tasting pork product, South Korean consumers show very strong preferences to pork that is higher in fat. Therefore, South Korean consumers have a higher demand for pork belly and Boston butt. Consequently, the supply and demand of pork in Korea is hardly met, which means that importation of high fat parts is inevitable. In Korea there is lower preference toward low fat parts such as loin, picnic shoulder, and ham. During the economic depression in South Korea there have been observable changes in consumer preferences. There remains steep competition among the pork exporting countries in terms of gaining share in the international pork market. If specific consumer preferences would be considered carefully, there is the possibility to increase the amount of pork exported to these countries.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.16 no.1
• /
• pp.117-124
• /
• 2020

3D printing is a technology that has significantly grown in recent years, particularly in the aerospace, defense, and medical sectors where it offers significant potential cost savings and reduction of the supply chain by allowing parts to be manufactured on-site rather than at a distance supplier. In nuclear industry, 3D printing technology should be applied according to the manufacturing trend change. For the application of 3D printing technology to the nuclear power plant, several problems, including the absence of code & standards of materials, processes and testing & inspection methods etc, should be solved. Preemptively, the improvement of reliability of 3D printing technology, including mechanical properties, structural performance, service performance and aging degradation of 3D printed parts should be supported. These results can be achieved by collaboration of many organizations such as institute, 3D printer manufacturer, metal powder supplier, nuclear part manufacturer, standard developing organization, and nuclear utility.

• Korean Journal of Computational Design and Engineering
• /
• v.10 no.2
• /
• pp.133-142
• /
• 2005

This paper proposes an object-oriented conceptual information model of mechanical assemblies, named open assembly model (OAM). The proposed assembly model primarily defines hierarchical relationships between parts and subassemblies. Together with the assembly hierarchy. the model also provides a way to represent tolerances, kinematic information, and parametric assembly constraints. Relational information such as mating conditions and degree of freedom between parts and subassemblies is captured via assembly features and relationships thereof. The information model is described using class diagrams of the Unified Modeling Language (UML), and instance diagrams are used to exemplify the proposed information model. The conceptual model presented in this paper is an integrated information model for assembly representation, which could supply necessary information for tolerance analysis and synthesis, kinematic simulation, and assembly simulation. Such a conceptual information model plays an important role for the exchange of information between modeling, analysis and planning systems. Hence, the proposed model could serve as a framework for developing data exchange standards of mechanical assemblies. The proposed model is demonstrated through a case study of a planetary gear assembly.

• Journal of Surface Science and Engineering
• /
• v.38 no.6
• /
• pp.234-240
• /
• 2005

In this study, ion nitriding of a EHA pump part made of AISI 4340 steel was performed under different applied power conditions to study the relationship between dimensional changes of specimens and the type of applied power source. Microstructures and micohardness distribution at different processing conditions were also examined. Duplex surface treatment of ion nitriding with the optimum process conditions to produce the minimum dimensional variation in a EHA pump part and a TiN thin film coating by unbalanced magnetron sputtering was performed and the specimens with a duplex surface treatment were subjected to a high speed wear test to evaluate the wear performance of EHA hydraulic pump parts with various surface treatment conditions. Results indicated that uniform and continuous surface layer with a minimum dimensional variation could be obtained by ion nitriding with bipolar mode power source and much enhanced wear characteristics with a duplex surface treatment could be obtained, compared with results from ion nitriding or single-layerd TiN coating specimens.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.1
• /
• pp.23-33
• /
• 2018

In the general manual feeder of an LED lighting assembly system, many workers are needed to supply parts to the main conveyor. The automatic feeder for modern automation lighting assembly systems consists of a completely automated feeding system and a magazine system that supplies the parts automatically. A standardized LED panel and diffusion cover is stacked in the cartridge of the magazine system. The structural safety of the automatic feeding system with regard to handling the load from the panels and covers stored in the cartridge should be guaranteed. LED convergency lighting modules are assembled using two LED panels and one diffusion cover in an automatic feeder. In this study, the structural safety and fatigue life of the automatic feeder and magazine were analyzed by considering the load generated in the automatically assembled LED convergency lighting system. In addition, the dynamic behavior of each auto-feeding system and magazine delivery system was visualized, and the working process was evaluated via dynamic simulation using a virtual engineering method. A tack time table for automatic feeding systems was derived by developing a virtual prototype.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.43 no.1
• /
• pp.123-131
• /
• 2020

There have been a lot of studies in the past for the method of predicting the failure of a machine, and recently, a lot of researches and applications have been generated to diagnose the physical condition of the machine and the parts and to calculate the remaining life through various methods. Survival models are also used to predict plant failures based on past anomaly cycles. In particular, special machine that reflect the fluid flow and process characteristics of chemical plants are connected to hundreds or thousands of sensors, so there are not many factors that need to be considered, such as process and material data as well as application of derivative variables. In this paper, the data were preprocessed through time series anomaly detection based on unsupervised learning to predict the abnormalities of these special machine. Next, clustering results reflecting clustering-based data characteristics were applied to produce additional variables, and a learning data set was created based on the history of past facility abnormalities. Finally, the prediction methodology based on the supervised learning algorithm was applied, and the model update was confirmed to improve the accuracy of the prediction of facility failure. Through this, it is expected to improve the efficiency of facility operation by flexibly replacing the maintenance time and parts supply and demand by predicting abnormalities of machine and extracting key factors.

• Journal of the Society of Naval Architects of Korea
• /
• v.46 no.2
• /
• pp.171-178
• /
• 2009

In this paper, RFID (Radio Frequency Identification) based management system is introduced to control effectively logistic supply items and machinery spare parts in a ship. To apply an RFID system under very harsh environment in a ship which is a steel-structured small area with lots of compartment, we measured reading distances and angles in open space, in an steel compartment, and an real ship separately in order to investigate the reliability between various tags and RFID.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.2
• /
• pp.79-84
• /
• 2011

In general, a valve body of the automatic transmission(AT) is controlled by the clutch, the brake and lubricating oil flow in a hydraulic system and lubricant flow for each valve can be adjusted independently. To increase the lifetime of AT, the lubrication flow rate in a valve body for a 6 speed AT based parallel hybrid electric vehicle must be provided with proper oil distribution and control. In this study, we carried out several experiments without the inner parts of AT and with a AT assembly. The variation of the flow rate on oil temperature and pressure between an oil supply port and the outlets of the lubrication port was evaluated and analyzed. In the case of AT without the inner parts, it was evident that as the oil required for an operation of the clutch and brake was discharged from the outlet port, the flow rate from each lubrication port is decreased. However, the flow rate of the AT assembly was slightly increased. In addition, the lubrication flow rate was increased with increasing the oil temperature, and also it was reduced with increasing the oil pressure. Details of the resulting data are discussed.