• 한국분무공학회지
• /
• 제3권3호
• /
• pp.42-48
• /
• 1998

This study describes the spray structure of gasoline port injectors by using phase Doppler particle analyzer(PDPA) and particle motion analysis system(PMAS). The characteristics of fuel spray such as the spray penetration, spray angle and breakup processes were obtained by PMAS and the droplet size and mean velocity were measured by PDPA system. Pintle type and two-hole type injectors were used as gasoline port fuel injectors under various injection pressures. The effect of injection pressure on the droplet mean diameter and axial mean velocity of droplet were investigated under the various injection conditions. In addition the comparison of breakup processes for the two types of injectors was also conducted. It Is shown that pintle type injector has smaller droplet size than that of two-hole type injector.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 추계학술대회 논문집
• /
• pp.169-172
• /
• 2007

HEV용 리튬이온 전지에 대한 연구는 최근에 많은 연구가 진행되고 있으며 그중 고용량 및 저렴한 가격, 환경에 대한 안정성으로 인해 Li-Mn spinel에 대한 성능향상 연구가 많이 이루어지고 있다. 본 연구에서는 Li-Mn spinel의 입자크기에 대한 기초 물성 과 전기적 특성을 측정하여 입자크기가 용량에 미치는 영향에 대한 고찰을 하였다. Li-Mn spinel의 비표면적, C-V 특성, 전기적 용량, coulomb efficiency 등을 통하여 입자의 크기와 전해액, Li의 구동등과 관련하여 용량특성에 향상을 가져오는 입자크기 조건을 정의하였고 그에 따라 온도별로 합성 한 후 입자사이즈에 대한 특성을 나타내었다.

• 한국수소및신에너지학회논문집
• /
• 제28권6호
• /
• pp.697-703
• /
• 2017

This study investigated the high-efficient process for bioethanol from barley by various condition. First, higher concentrations of ethanol could be produced without loss of yield by using reducing water consumption. This is because it could prevent to increase viscosity despite reducing water consumption. Second, the ethanol yield could be improved by using reducing particle size of biomass (increase of enzyme reactive surface). Third, The addition of protease could have a considerable effect on yield of fermentation, which provides nutrients to the yeast. This results showed that bioethanol production would provide efficient ethanol production and lower production costs.

• Macromolecular Research
• /
• 제11권3호
• /
• pp.198-201
• /
• 2003

Aqueous emulsion of polyurethane (PU) ionomers were reinforced with hydrophobic nanosilica to give composites. The aqueous emulsion was stable and the particle size increased as the content of hydrophobic nanosilica was increased. The reinforcing effect of nanosilica in mechanical properties of these composites were examined by dynamic mechanical and tensile tests, and the Shore A hardness was measured. Enhanced thermal and water resistance and marginal reduction in transparency of these composites were observed compared with pristine polymer. These results were similar with those of our previous studies on waterborne PU/organoclay nanocomposites.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.1
• /
• pp.304-307
• /
• 2003

Replacement of aluminum by copper for interconnections in the semiconductor industry has raised a number of important issues. The integration of copper interconnection can be carried out by CMP(chemical mechanical polishing) is used to planarize the surface topography. In this experiments, we evaluated the optimization of several conditions for chemical additives during Cu CMP process. It was presented that the main cause of grown particle size is tartaric acid. The particle size was in inverse propotion to a quantity of bead and the time of milling process. The slurry stabilizer and oxidizer have been shown to have very good effect by addition in later milling process.

• 대한기계학회논문집B
• /
• 제25권4호
• /
• pp.496-506
• /
• 2001

The effect of corona discharge on soot emission was experimentally investigated. Size and number concentrations of soot aggregates were measured and compared for various voltages. Regardless of the polarity of the applied voltage, the flame length decreased and the tip of flame spreaded with increasing voltage. For the experimental conditions selected, the flame was blown off toward the ground electrode by corona ionic wind. When the negative applied voltage was greater than 3kV(for electrode spacing = 3.5cm), soot particles in inception or growth region were affected by the corona discharge, resulting in the reduction of number concentration. The results show that the ionic wind favored soot oxidation and increased flame temperature. Number concentration and primary particle size greatly increased, when the corona electrodes were located the region of soot nucleation or growth(close to burner mouth).

• 정보저장시스템학회:학술대회논문집
• /
• 정보저장시스템학회 2005년도 추계학술대회 논문집
• /
• pp.179-183
• /
• 2005

Particles in the HDD can cause serious damages such as scratches and thermal asperity(TA) at the head/disk interface(HDI). Accordingly, particles cause data loss including physical and electrical damages. To improve the reliability of head-disk interface, understanding the damage characteristics at the HDI due to particle interactions is required. The materials such as $A1_2O_3$, TiC and aluminum were used in this experiment. The size and hardness of particles injected into the HDI are closely relevant to surface damage caused the data loss on the disk and head. In this paper, a variety of scratches were analyzed using scanning electron microscope(SEM) and atomic force microscope(AFM). In order to analyze defects of very small size on the disk, optical surface analyzer(OSA) was also used.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 추계학술대회 논문집 Vol.15
• /
• pp.195-197
• /
• 2002

CdTe quantum dots(QDs) were synthesized in aqueous solution by colloidal method. Photoluminescence(PL) spectra of the synthesized CdTe QDs revealed the intensity of PL peaks was stronger as the condensation time was longer. This result was thought because annealing effect by thermal energy transferred during condensation eliminated defects which act as traps and recombination centers in CdTe particle. PL intensity has stron dependence of Te precursor concentration. It confirmed the ratio of Te ion to Cd ion added during synthesis affected the particle size and size distribution of the CdTe QDs. Finally, the synthesized CdTe QDs were identified to be cubic structured CdTe quantum dots by X-ray diffraction(XRD).

• Bulletin of the Korean Chemical Society
• /
• 제29권2호
• /
• pp.328-334
• /
• 2008

The effects of catalyst preparation on the reaction route and the mechanism of biphenol (BP) hydrogenation, which consists of a long series-reaction, were studied. Pd/C catalysts were prepared by incipient wetness method and precipitation and deposition method. The reaction behaviors of the prepared catalysts and a commercial catalyst along with the final product distributions were very different. The choice of the catalyst preparation conditions during precipitation and deposition including the temperature, pH, precursor addition rate, and reducing agent also had significant effects. The reaction behaviors of the catalysts were interpreted in terms of catalyst particle size, metal distribution, and support acidities.

• 수산해양교육연구
• /
• 제28권6호
• /
• pp.1875-1881
• /
• 2016

The wear behavior for the two types of composites, those are epoxy matrix composites filled with silica particles and aluminium matrix composites filled with SiC particles, were compared to investigate the wear mechanism for these composites. Especially, the effect of the volume fraction for the epoxy matrix composites and the particle size for the aluminium matrix composites according to the apply load and sliding velocity were investigated. Wear tests of the pin-on-disc mode were carried out and followed by scanning electron microscope observations for the worn surface. The addition of the fillers in the composites were improved the wear resistance significantly and changed the wear mechanism for the both composites. These results were identified by the observation of the worn surface after testing.