• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.11
• /
• pp.864-868
• /
• 2010

Among LTCC material for substrate, the crystallized anorthite system was mainly studied as high strength material. However, specific factors that have affected on strength of material were studied insufficiently on anorthite system. In this study, the composition of anorthite glass was Ca-Al-Si-Zn-O. The changes of phase and microstructure were observed with the amount and the particle size of glass and the sintering temperature. It was studied that the factors affected on the strength of material. Phases of anorthite and $ZnAl_2O_4$ were formed with the increase of sintering temperature. The $Al_2O_3$ phase was increased with $Al_2O_3$ amount, acted as filler, and the strength of material is increased with $Al_2O_3$ phase. But phases of anorthite and $ZnAl_2O_4$ didn't affect on the strength of material. In the case of 60 vol% glass amounts and below $3.2\;{\mu}m$ of glass particle size, the strength of material was decreased. It is thought that the decrease of strength was due to non-homogeneous mixing between glass powder and filler.

• Resources Recycling
• /
• v.13 no.6
• /
• pp.9-15
• /
• 2004

The optimum conditions were studied for the preparation of transparent iron oxide with the air oxidation of FeOOH. The FeOOH obtained by mixing NaOH and FeSO$_4$ solution in various conditions such as R(=2NaOH/FeSO$_4$), FeSO$_4$ concentration. reaction temperature and air flow rate. When the FeSO$_4$ increased gradually, the concentration of iron ion in the solution became high. So, particle size increased precipitating Fe$_3O_4$. Goethite dehydrate at about 200$^{\circ}C$ and ended the reaction at about 320$^{\circ}C$ forming hematite. The lower the reaction temperature was, the shorter the particle length of goethite and particle size decreased. When the flow rate of air as an oxidant increased, the amount of dissolved oxygen in the solution increased, which made oxidation rate increased. And then particle size of goethite decreased.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.5
• /
• pp.1671-1678
• /
• 1996

In external chemical vapor deposition processes including VAD and OVD the distribution of flame-synthesized silica particles is determined by heat and mass transfer limitations to particle formation. Combustion gas flow velocities are such that the particle diffusion time scale is longer than that of gas flow convection in the zone of particle formation. The consequence of these effects is that the particles formed tend to remain along straight smooth flow stream lines. Silica particles are formed due to oxidation and hydrolysis. In the hydrolysis, the particles are formed in diffuse bands and particle formation thus requires the diffusion of SiCl$\_$4/ toward CH$\_$4//O$\_$2/ combustion zone to react with H$\_$2/O diffusing away from these same zones on the torch face. The conversion kinetics of hydrolysis is fast compared to diffusion and the rate of conversion is thus diffusion-limited. In the language of combustion, the hydrolysis occurs as a Burke-Schumann process. In selected conditions, reaction zone shape and temperature distributions predicted by the Burke-Schumann analysis are introduced and compared with experimental data available. The calculated centerline temperatures inside the reaction zone agree well with the data, but the calculated values outside the reaction zone are a little higher than the data since the analysis does not consider diffusion in the axial direction and mixing of the combustion products with ambient air. The temperatures along the radial direction agree with the data near the centerline, but gradually diverge from the data as the distance is away from the centerline. This is caused by the convection in the radial direction, which is not considered in the analysis. Spatial distribution of silica particles are affected by convection and diffusion, resulting in a Gaussian form in the radial direction.

• Korean journal of food and cookery science
• /
• v.30 no.5
• /
• pp.526-530
• /
• 2014

The effect of roasting on particle size distribution, water-holding capacity, and viscosity of sunsik was investigated in this study using non-roasted one as control. Roasting increased the size of particles in sunsik, in particular, particles larger than $1{\mu}m$ in diameter, indicating that roasted sunsik is likely to sediment faster, thereby decreasing the time to maintain dispersibility when mixing with water. Roasting also increased the water-holding capacity of sunsik, indicating that polymerization occurred greater than a pyrolysis during roasting, leading to increased viscosity in roasted sunsik. These results indicate that the roasting affected the dispersibility and viscosity of sunsik by increasing particle size and water-holding capacity, respectively.

• Journal of Soil and Groundwater Environment
• /
• v.19 no.6
• /
• pp.72-79
• /
• 2014

Cavitation generated by ultrasonic irradiation can enhance the diffusional transport of organic contaminants from soil surfaces or pores. Therefore, ultrasound soil washing can be an alternative of traditional soil washing process. In this study, soil was artificially contaminated with n-tetradecane, n-hexadecane and phenanthrene. A plate type ultrasonic reactor at 25 kHz frequency and 1000W power was used for laboratory soil washing experiments. Ultrasonic soil washing efficiency was compared with those of traditional soil washing using mechanical mixing. Various operational parameter such as soil/liquid ratio, irradiation time, particle size, and soil organic matter content was tested to find out the optimum condition. It was found that ultrasonic soil washing demonstrates better performance than mechanical soil washing. Optimum soil:liquid ratio for ultrasonic soil washing was 1 : 5. Desorption of organic contaminants from soils by ultrasonic irradiation was relatively fast and reached equilibrium within 10 minute. However, decrease in the soil particle sizes by ultrasonic irradiation results in re-adsorption of contaminants to soil phase. It was also observed that soil particle size distribution and soil organic matter content have significant effects on the efficiency of ultrasonic soil washing.

• Advances in nano research
• /
• v.5 no.4
• /
• pp.359-372
• /
• 2017

Metallic copper nanoparticles were synthesised by reduction of copper ions in aqueous solution, and metal-metal bonding by using the nanoparticles was studied. A colloid solution of metallic copper nanoparticles was prepared by mixing an aqueous solution of $CuCl_2$ (0.01 M) and an aqueous solution of hydrazine (reductant) (0.2-1.0 M) in the presence of 0.0005 M of citric acid and 0.005 M of n-hexadecyltrimethylammonium bromide (stabilizers) at reduction temperature of $30-80^{\circ}C$. Copper-particle size varied (in the range of ca. 80-165 nm) with varying hydrazine concentration and reduction temperature. These dependences of particle size are explained by changes in number of metallic-copper-particle nuclei (determined by reduction rate) and changes in collision frequency of particles (based on movement of particles in accordance with temperature). The main component in the nanoparticles is metallic copper, and the metallic-copper particles are polycrystalline. Metallic-copper discs were successfully bonded by annealing at $400^{\circ}C$ and pressure of 1.2 MPa for 5 min in hydrogen gas with the help of the metalli-ccopper particles. Shear strength of the bonded copper discs was then measured. Dependences of shear strength on hydrazine concentration and reduction temperature were explained in terms of progress state of reduction, amount of impurity and particle size. Highest shear strength of 40.0 MPa was recorded for a colloid solution prepared at hydrazine concentration of 0.8 M and reduction temperature of $50^{\circ}C$.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.1
• /
• pp.32-38
• /
• 2023

In this study, as part of the practical development of technology for CLSM using pond ash, the characteristics such as flowability, bleeding rate, and strength of the CLSM according to physical properties such as particle size distribution and particulate content of the pond ash were reviewed. As a result of analyzing the properties of the collected pond ash, it was found that the characteristics of density and particle size distribution were different. As a result of evaluating the characteristics of the CLSM for three types of pond ash, it was found that the blending conditions to satisfy the quality stipulated in ACI 229R were different, and mainly affected the particle size distribution characteristics and particulate content of the pond ash. In case of coarse-grained pond ash (PA-3), mixing conditions that satisfy the performance requirements stipulated in ACI 229R were not derived. But it is considered that further review is necessary according to particle size adjustment.

• Journal of Soil and Groundwater Environment
• /
• v.16 no.4
• /
• pp.1-9
• /
• 2011

Bentonite has been generally used as vertical cutoff barrier material and reported to have several problems regarding its low workability, drying shrinkage cracking by particle cohesion, and ineffective waterproof ability under sea water condition. In this study, the particle sealant, the furnace slag coated by the mixture of bentonite, sepiolite and guargum, was developed to compensate these weak points and the hydraulic conductivity of the particle sealant was evaluated. Drying shrinkage cracking and swelling index was estimated to find the optimal mixing ratio of bentonite, sepiolite and guargum. The hydraulic conductivity of the particle sealants having different amount of sealant (bentonite-sepioliteguargum mixture) coating the furnace slag was estimated using the rigid wall permeameter and flexible wall permeameter. The results showed that drying shrinkage cracking was not found in the bentonite-sepiolite mixture with 20% sepiolite contents and the results from free swelling tests for the sealant having 1 : 0.025, 1 : 0.05 and 1 : 0.075 of weight ratios of bentonite-sepiolite mixture and guargum under simulated sea water condition were higher than those for the bentonitesepiolite mixture without guargum under tap water condition. These three sealants were coated on the furnace slag with 50% and 60% of sealant in the particle sealant and the hydraulic conductivity was estimated. In the cases of the particle sealants having 20% sepiolite in the bentonite-sepiolite mixture and 1 : 0.075 weight ratio of the bentonite-sepiolite mixture and guargum, the hydraulic conductivity from the rigid wall permeameter was below $1.0{\times}10^{-7}$ cm/sec under simulated sea water condition. The hydraulic conductivity of the particle sealant having $1.0{\times}10^{-6}$~$1.0{\times}10^{-7}$ cm/sec by the rigid wall permeameter was estimated using the flexible wall permeameter and found to be below $1.0{\times}10^{-7}$ cm/sec.

• Journal of Adhesion and Interface
• /
• v.3 no.2
• /
• pp.9-16
• /
• 2002

In the synthesis of water-based polyurethane using self-emulsification process, after being neutralized, polyurethane pre-polymers containing ionic pendant groups are dispersed by simple convective mixing. Preparation of dispersion is followed by chain extension reaction, which is considered as important step for growth of the molecular weight of polyurethane. In this work, pH variations in the aqueous phase were monitored during the chain extension process in the presence of water-soluble diamines. The optimum degree of chain extension and the average particle size in the polyurethane dispersions were examined with varying ionic pendent group contents, type of chain extenders, and feed rate of chain extenders, The initial pH value in the aqueous phase linearly increased and the optimum chain extension point could be obtained from the intersection of two linear lines having different slopes, All average particle sizes before chain extension reaction were almost same, however, the final average particle size increased as feed rates of chain extenders increased, In addition, as the ionic pendant group contents increased, the particle size decreased since the hydrophilicity and hydrodynamic volume increased. As carbon numbers of the chain extenders increased, the final particle size increased significantly. From the results, it was concluded that the chain extension reaction took place among the particles not only in a particle.

• Journal of the Microelectronics and Packaging Society
• /
• v.10 no.4
• /
• pp.65-71
• /
• 2003

A new type of ultrasonic spray nozzle was fabricated employing a piezoelectric device. The spray nozzle was designed to disperse chemicals in a water treatment mixing tank. The piezoelectric properties in ultrasonic spray nozzles were optimized to improve the dispersion of chemicals. The piezoelectrics were packaged in an aluminum case with silicone resin for the aqueous solution proof packaging. Chemicals were dispersed with high efficiency and the chemicals consumption was reduced by the ultrasonic fine particle spraying. The concentration of Escherichia coli in mixing tank was decreased remarkably using ultrasonic spray nozzle dispersion compared to the conventional methods.