• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2004년도 추계학술대회 논문집
• /
• pp.44-47
• /
• 2004

Vortexing might occur during draining from tanks which reduces the rate of outflow. This phenomenon has practical relevance in the fuel feed system in space vehicles and rockets. Due to environmental disturbances rotational motion can be generated in the liquid-propellant tank, which in turn can affect the rate of outflow to the engines. The phenomenon is initialized by rotating the fluid In the experimental tank. The dip quickly develops into a vortex with an air core, which extends to the bottom port, reducing the effective cross-sectional area of the drain outlet and consequently the flow rate. Flow characteristics are investigated using SPIV(Stereoscopic Particle Image Velocimetry) method.

• 한국항공우주학회지
• /
• 제46권5호
• /
• pp.359-367
• /
• 2018

회전익기가 하강 비행 시 발생하는 와류 고리 상태는 회전면 근처에 도넛 모양의 순환유동을 발생시키며, 추력 상실로 인한 기체의 추락을 유발한다. 본 논문에서는 무인 비행체의 종류 중 하나인 쿼드콥터의 와류 고리 상태에서의 유동장을 물리적으로 규명하였다. 한국항공우주연구원 1m 아음속 풍동에서 쿼드콥터의 하강 비행을 모사했으며, 유동장 계측을 위해 입자 영상 유속계(PIV)를 이용했다. 정지 비행 상태의 유도 속도를 운동량이론을 이용하여 추정하고, 이를 통해 와류 고리 상태를 유발할 수 있는 하강 속도의 범위에서 시험을 수행하였다. 또한 하강률에 따른 유동장 계측뿐만 아니라 프로펠러 간의 간격을 달리 주어서도 와류 고리의 발달 및 진행방향을 확인하였다. 더불어 본 연구 결과는 쿼드콥터 주변의 유속 측정을 통해서도 와류 고리 상태를 예측할 수 있다는 것을 보여준다.

• 대한기계학회논문집B
• /
• 제28권3호
• /
• pp.315-323
• /
• 2004

An electrical cascade impactor is a multi-stage impaction device to separate airborne particles into aerodynamic size classes using particle charging and electrical detection techniques. A Faraday cage and an aerosol charger, which are basic components of the electrical cascade impactor, were designed and evaluated in this study. The low-level current response of the Faraday cage was investigated with changing particle size and air flow rate by using sodium chloride (NaCl) particles. The response of the prototype Faraday cage was very similar to that of a commercial aerosol electrometer (TSI model 3068) within ${\pm}$5% for singly-charged particles. The response linearity of the prototype Faraday cage could be extended up to flow rate of 30 L/min. For the performance evaluation of the aerosol charger the monodisperse liquid dioctyl sebacate (DOS) particles, with diameters of 0.1∼0.8$\mu\textrm{m}$, were generated using spraying from an atomizer followed by evaporation-condensation process. Typical performance parameters of the aerosol charger such as P$.$n, wall loss, and elementary charges per particle were evaluated. The performance of the prototype aerosol charger was found to be close to that of the aerosol charger used in an electrical low pressure impactor (ELPI, Dekati).

• Korean Chemical Engineering Research
• /
• 제55권3호
• /
• pp.279-286
• /
• 2017

This review paper evaluates different kinds of synthesis methods for calcite precipitated calcium carbonates by using different materials. The various processing routes of calcite with different compositions are reported and the possible optimum conditions required to synthesize a desired particle sizes of calcite are predicted. This paper mainly focuses on that the calcite morphology and size of the particles by carbonation process using loop reactors. In this regard, we have investigated various parameters such as $CO_2$ flow rate, Ca $(OH)_2$ concentration, temperature, pH effect, reaction time and loop reactor mechanism with orifice diameter. The research results illustrate the formation of well-defined and pure calcite crystals with controlled crystal growth and particle size, without additives or organic solvents. The crystal growth and particle size can be controlled, and smaller sizes are obtained by decreasing the Ca $(OH)_2$ concentration and increasing the $CO_2$ flow rate at lower temperatures with suitable pH. The crystal structure of obtained calcite was characterized by using X-ray diffraction method and the morphology by scanning electron microscope (SEM). The result of x-ray diffraction recognized that the calcite phase of calcium carbonate was the dominating crystalline structure.

• 대한기계학회논문집B
• /
• 제24권3호
• /
• pp.443-449
• /
• 2000

The performance of 2-frame PTV(particle tracking velocimetry) system was improved using an adaptive hybrid scheme. The original 2-frame PTV method based on the match probability concept employs global match parameters for the entire flow field. Since this does not reflect fully the detailed local velocity change, it sometimes reduces the recovery rate of velocity vectors and increases the number of erroneous vectors in the region where an extraordinary flow structure exists. In this study, the preliminary FFT-based PIV results are used as an input parameter to determine the local match parameters needed for the 2-frame particle tracking algorithm. A computer simulation using synthetic particle images was carried out to study the performance of the adaptive 2-frame PTV technique. The adaptive hybrid method shows the better performance with increasing the velocity vector recovery rate and decreasing the computation time, compared to the original 2-frame PTV method.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.404-409
• /
• 2000

Growth characteristics of silica particles have been studied experimentally using in situ sampling technique from $H_2/O_2TEOS$ diffusion flame with carefully devised sampling probe. Verification of sampling result was done through new method and effects of flame condition and TEOS flow rate on growth characteristics of silica particles were investigated. By comparing particles sampled by thermophoretic sampling in flame with those by collector sampling after probe, particles do not change before and after probe sampling, which was clearly proved from the fact that the result of TEM image analysis makes good agreement with that of SMPS measurement. As flame temperature increases, the effect of coalescence or sintering becomes important mechanism during growth of silica particles, resulting in canceling the effect of coagulation, which makes mean diameter of silica particles increase slowly. With increase in TEOS flow rate, the number concentration of generated silica particle increases but residence time of particles in flame decreases. As a result, there exists upper limit to which the diameter of silica particle increases under same flame condition.

• Asian Journal of Atmospheric Environment
• /
• 제8권2호
• /
• pp.89-95
• /
• 2014

There have been a lot of efforts to keep permissible emission standards and to reduce the amount of emitted air pollutants. There are several air pollution control equipments, however, wet scrubber is used to remove particulate matters and gaseous pollutants simultaneously, even if it has low collection efficiency in the particle size less than $5.0{\mu}m$. To overcome this problem, we introduced a spray tower scrubber with an electrospray system which a high voltage was indirectly applied. We found that collection efficiency of fine particles in the electrospray system was improved by increasing electrical field strength and the ratio of liquid-gas flow rate (from 41% to 84% for $0.3{\mu}m$ particles). In addition, a number of small droplets generated from an electrospray system led high collection efficiency, resulting from electrostatic attraction between droplets and particles and higher collision frequency. Therefore, we can conclude that the introduction of an electrospray system is quite effective to increase the particle removal efficiency of a spray tower scrubber.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권10호
• /
• pp.1237-1243
• /
• 2014

The aim of the present paper is to analyze the friction and mass flow in a rough microchannel using Lattice Boltzmann Method (LBM). The LBM is a kinetic method based on the particle distribution function, so it can be fruitfully used to study the flow dependence on Knudsen number including slip velocity, pressure drop in rough microchannel. The surface roughness elements are taken to be considered as a series of circular shaped riblets throughout the channel with relative roughness height up to a maximum 10% of the channel height. The friction coefficients in terms of Poiseuille number (Pn), mass flow rate and the flow behaviors have been discussed in order to study the effect of surface roughness in the slip flow regime at Knudsen number (Kn), ranging from 0.01 to 0.10. It is seen that the friction factor and the flow behaviors in a rough microchannel strongly depend on the rarefaction effect and the relative roughness height. The friction factor in a rough microchannel is higher than that in smooth channel but the mass flow rate is lower than that of smooth channel. Moreover, it is seen that the friction factor increased with relative roughness height but decreased with increasing the Kundsen number (Kn) whereas the mass flow rate is decreased with increasing both of surface roughness height and Knudsen number.

• 한국가시화정보학회지
• /
• 제12권1호
• /
• pp.25-29
• /
• 2014

The outlet flow of the centrifugal blower were quantitatively visualized using particle image velocimetry. Because the centrifugal blower is one of the key parts of electric vehicle battery cooling system, the quantitative information of centrifugal blower is necessary to design and optimize the cooling system. The effect of different inlet flow condition to the outlet flow was investigated in this study. Two different inlet ducts were used. One is the straight inlet and the other is a bended one. The results clearly showed the outlet flow asymmetry in both inlet ducts. When the blower has the bended inlet, the flow rate decreases due to the increase of the head loss.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2001년도 추계학술대회 논문집
• /
• pp.160-163
• /
• 2001

In order to develop a nodule conveying system through a flexible pipe out of the deep-seabed manganese nodule miner, an experimental study of the solid-water slurry flow in vertical pipe is performed as the first stage of total experiments. Hydraulic characteristics of the pipe slurry flow such as slip velocity, transport concentration and pressure gradient are investigated for the size of particle, load ratio, and flow rate of water. The higher the load ratio is, the larger the transport concentration and pressure gradient become. The bigger the size of particles is, the larger the pressure gradient becomes. The effectiveness of the flow rate to hydraulic performance is also investigated. This results are to be used for designing crusher and pump, and operating the conveying device.