• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 1999년도 제1회 학술대회논문집(KIASC 1st conference 99)
• /
• pp.153-156
• /
• 1999

In this paper, the inertance tube is modeled by the distributed impedance model. This model is verified by the analytical solutions for the long tube without the reservoir. In this model the distributed impedace effect of the inertance tube is included and mass flow rate and pressure distributions are calculated along the inertance tube for various inertance tube lengths. Mass flow rate at the inlet of the inertance tube is also calculated by this model and compared to the lumped impedance method. Mass flow rate by the distributed model shows quite different behaviors from the lumped model when the operating frequency is high and the length of the tube becomes large.

• 유공압시스템학회논문집
• /
• 제5권2호
• /
• pp.8-13
• /
• 2008

Shell-and-tube type heat exchangers are generally classified with fixed tube-sheet and floating tube-sheet heat exchangers. In this paper, we employed the fixed tube-sheet heat exchangers. We theoretically investigated the safety evaluation of our shell-tube heat exchanger by axial, bending and equivalent stress of fin tubes, tube plates, channels and shell. Design pressure ranges were chosen pressure($0.6{\sim}2\;MPa$) on tube side and 200 %(3 MPa) of Maximum pressure on shell side for safety evaluation of heat exchangers. This research will be useful for fabrication of heat exchangers to prevent against damage hazard of heat exchangers in operation.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2003년도 가을 학술발표회 논문집
• /
• pp.325-332
• /
• 2003

The tube structures act like cantilevered box beams and effectively resist lateral loads. In result, they are adopted as a high-rise buildings system. However, the shear lag in tube system prevents the idealized tube behavior such as a cantilevered box beam. Therefore, the studies on shear lag phenomena are necessarily requested. The presented papers are almost studied on framed tube structures and tube in tube structures. However, the study on the shear lag in the tube structure with core wall is lack. Thus, in this paper, the shear lag of the structure is studied. The shear lag coefficient is defined to investigate shear lag phenomena. However, existing shear lag coefficients are not adequate for understanding them. Therefore, on this study, new shear lag coefficient is suggested. In addition, the shear lag in the tube structure with core wall is analyzed by changing the five structural parameters of stiffness factor in frame, stiffness factor in wall, stiffness ratio, the number of stories and the number of bays.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2002년도 학술대회 논문집
• /
• pp.98-100
• /
• 2002

We developed the Centrifugal Forming Process(CFP) for HTS tube fabrication. The self-designed equipment for CFP is devided into 3 main parts depending on its role and functions. the melting part by heating of high inductive frequency, centrifugal forming part for the tube and efficient microstructure control of Bi2212 phase and molding part for tube detachment after heat treatment. In this paper we will introduce self designed Centrifugal Forming Process for HTS tube fabrication and discuss about the results related mold materials in terms of high Tc superconductor.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.244-248
• /
• 2003

Recently social demands of fuel economy and environmental regulations require the development of light materials and new manufacturing technologies. In this point, the aluminum tube hydroforming process which is satisfied with good strength-to-weight ratio and recyclability is innovative concept. However the level of the aluminum tube hydroforming technology is low in comparison with that of steel tube hydroforming. In this paper, the hydroformability of aluminum tubes in different heat treatments is presented. Theoretical results for forming limits of the wrinkling and bursting are compared with experimental results of aluminum tubes.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 1999년도 제1회 학술대회논문집(KIASC 1st conference 99)
• /
• pp.189-193
• /
• 1999

An experimental study was carried out to improve the cooling capacity and performance of the pulse tube refrigerator. Three buffer pulse tube refrigerator was designed and fabricated, and the experimental apparatus was constructed. This paper presents operating process of three buffer pulse tube refrigerator and results obtained with the performance test. The cooldown characteristics and load characteristics are described. The lowest temperature measured in three pulse tube refrigerator was 88K and the cooling capacity at the optimum operating condition was 27W at 120K.

• The Journal of the Acoustical Society of Korea
• /
• 제19권2E호
• /
• pp.20-26
• /
• 2000

A conceptual simplified model of Hartmann-Sprenger tube is suggested and investigated to decouple the regurgitant mode in the present paper. In spite of high nonlinearity, the acoustic behavior of this resonant tube system is dependent on wavelength and depth of the tube. The effect of forcing frequency and tube geometry on jet regurgitant mode are studied and discussed. With a conventional axisymmetric Euler code, sensitive acoustic problems are solved and validated by comparison with analytic theories.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 춘계학술대회논문집
• /
• pp.7-13
• /
• 1999

Hydroforming is the technology that utilizes hydraulic pressure to form sheet and tube metals in to desired shapes inside die cavities. It can be subdivided into tube hydroforming and sheet hydroforming according to the blanks used. In this paper the simulation of tube and welded blank hydroforming is carried out respectiyely. And simulation results are compared to evaluate formability in tube and welded blank hydroforming of engine mount bracket

• 소성∙가공
• /
• 제9권6호
• /
• pp.631-637
• /
• 2000

The tube hydroforming technology is new key production technologies, which contribute to a light-weight cu. Because the tubes are used for hydroforming instead of the sheet materials formability test for tube is required to measure the formability of materials for hydroforming. In this Paper, a kind of formability test for tube, which can well represent the characteristics of tube hydroforming processes, is developed. Developed formability test method can consider not oかy the influence of material Properties but also contact with die and material. Some investigation was carried out to verify the effectiveness of developed formability test.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2015년도 제51회 KOSCO SYMPOSIUM 초록집
• /
• pp.169-172
• /
• 2015

This paper presents a numerical investigation on kerosene-air mixture detonation and behaviors of thermal elasto-plstic thin metal tube under detonation loading based on multi-material analysis. The detonation loading is modeled by the kerosene-air mixture detonation which is compared with CJ condition and experimental cell size. And the thermal softening effect on elasto-plstic model of metal tube is indicated by different dynamic response of detonation loaded tube in various temperature and tube thickness.