• 한국인쇄학회지
• /
• 제15권2호
• /
• pp.25-40
• /
• 1997

This research was carried out to investigated the effect of base paper and latex binder on printability and obtical properties of coated paper. Especially, it examined the effect of th pH of vase paper surface and functional groups of latices on the interactions between coating color components and on the structure of coated layer. It was found that the behavior of coating color containing amphoeric latex depends on the pH in the boundary region between coating color and base paper. Thus, the coating color formulated with amphoteric latex formed bulky coating layer by inducing stronger interaction between paper surface and coating components than the coating color with anionic latex. The coated paper with amphoteric latex showed better optical properties (i.e.gloss and optical) and printability (i.e. ink receptivity, wet ink receptivity, and ink set off) than the conventional anionic latex in the acidic and alkaline paper. However, dry pick strength of the coated paper was less decreased. This result indicated that amphoteric latex could also be applied practically to the alkaline paper.

• Journal of Welding and Joining
• /
• 제29권1호
• /
• pp.99-106
• /
• 2011

Joint strength between a solder ball and a pad on a substrate is one of the major factors which have effects on electronic device reliability. The effort to improve solder joint strength via surface cleaning, heat treatment and solder composition change have been in progress. This paper will discuss the method of solder ball joint strength improvement using LF hydrogen radical cleaning treatment and focus on the effects of surface treatment condition on the solder ball shear strength and interfacial reactions. In the joint without radical cleaning, voids were observed at the interface. However, the specimens cleaned by hydrogen-radical didn't have voids at the interface regardless of cleaning time. The shear strength between the solder ball and the pad was increased over 120%(about 800gf) when compared to that without the radical treatment (680gf) under the same reflow condition. Especially, at the specimen treated for 5minutes, ball shear strength was considerably increased over 150%(1150gf). Through the observation of fracture surface and cross-section microstructure, the increase of joint strength resulted from the change of fracture mode, that is, from the solder ball fracture to IMC/Ni(P) interfacial fracture. The other cases like radical treated specimen for 1, 3, 7, 9min. showed IMC/solder interfacial fracture rather than fracture in the solder ball.

• 한국해양공학회지
• /
• 제12권1호
• /
• pp.32-38
• /
• 1998

This paper is to investigate of microhardness, adhesive strength, tensile strength, and fatigue strength of ceramic sprayed steel. Rotary bending fatigue tests have been conducted at room temperature in air and 3% NaCl solution using specimens of carbon steel(S45C) with sprayed coating layers of Ni-4.5% Al(under coating) and $TiO_2$ (top coating). The microhardness has been improved at $800^{\circ}C$ heat treatment and 150mm spraying distance. Tensile strength of the sprayed steel is dependent on the substrate strength. The fatigue strength of the sprayed steel is larger than that of substrate due to blasting and constraint surface of plastic deformation effect. In low stress level, the corrosion fatigue strength of the sprayed steel were lower than that of fatigue strength in air by corrosion.

• The Journal of Advanced Prosthodontics
• /
• 제8권4호
• /
• pp.285-289
• /
• 2016

PURPOSE. This study evaluated the effect of chemical surface treatment using methyl formate-methyl acetate (MF-MA) solution on the tensile bond strength between acrylic denture teeth and auto-polymerized acrylic resin. MATERIALS AND METHODS. Seventy maxillary central incisor acrylic denture teeth for each of three different brands (Yamahachi New Ace; Major Dent; Cosmo HXL) were embedded with incisal edge downwards in auto-polymerized resin in polyethylene pipes and ground with silicone carbide paper on their ridge lap surfaces. The teeth of each brand were divided into seven groups (n=10): no surface treatment (control group), MF-MA solution at a ratio of 25:75 (v/v) for 15 seconds, 30 seconds, 60 seconds, 120 seconds, 180 seconds, and MMA for 180 seconds. Auto-polymerized acrylic resin (Unifast Trad) was applied to the ground surface and polymerized in a pressure cooker. A tensile strength test was performed with a universal testing machine. Statistical analysis of the results was performed using two-way analysis of variance (ANOVA) and post-hoc Dunnett T3 test (${\alpha}$=.05). RESULTS. The surface treatment groups had significantly higher mean tensile bond strengths compared with the control group (P<.05) when compared within the same brand. Among the surface treatment groups of each brand, there were no significantly different tensile bond strengths between the MF-MA groups and the MMA 180 second group (P>.05), except for the Yamahachi New Ace MF-MA 180-second group (P<.05). CONCLUSION. 15-second MF-MA solution can be an alternative chemical surface treatment for repairing a denture base and rebonding acrylic denture teeth with auto-polymerized acrylic resin, for both conventional and cross-linked teeth.

• 조명전기설비학회논문지
• /
• 제27권1호
• /
• pp.85-91
• /
• 2013

This paper studied surface discharge characteristics by a dielectric constant and diameter of solid dielectrics in $N_2/O_2$ mixture gas. Applied electric field strength at $N_2/O_2$ mixture gas was changed from the dielectric constant and diameter of the solid dielectrics, and insulation performance of the $N_2/O_2$ mixture gas determined surface discharge voltage. In each of the diameter at the solid dielectrics, the surface discharge voltage was increased by lengthening surface distance, whereas increasing rate of the surface discharge voltage was different from gas pressure. Thus, In this paper, main factors of surface discharge are as follows. 1) Insulation performance of $N_2/O_2$ mixture gas, 2) Dielectric constant of solid dielectrics, 3) Surface discharge path. It was clear that the surface discharge voltage depend on the main factors. These results will be applied to useful data for an eco-friendly composite insulation design.

• Computers and Concrete
• /
• 제15권2호
• /
• pp.215-229
• /
• 2015

The emerging technology of self compacting concrete, fiber reinforcement together reduces vibration and substitute conventional reinforcement which help in improving the economic efficiency of the construction. The objective of this work is to find the regression model to determine the response surface of mix proportioning Steel Fiber Reinforced Self Compacting Concrete (SFSCC) using statistical investigation. A total of 30 mixtures were designed and analyzed based on Design of Experiment (DOE). The fresh properties of SCC and mechanical properties of concrete were studied using Response Surface Methodology (RSM). The results were analyzed by limited proportion of fly ash, fiber, volume combination ratio of two steel fibers with aspect ratio of 50/35: 60/30 and super plasticizer (SP) dosage. The center composite designs (CCD) have selected to produce the response in quadratic equation. The model responses included in the primary stage were flowing ability, filling ability, passing ability and segregation index whereas in harden stage of concrete, compressive strength, split tensile strength and flexural strength at 28 days were tested. In this paper, the regression model and the response surface plots have been discussed, and optimal results were found for all the responses.

• Journal of Welding and Joining
• /
• 제27권5호
• /
• pp.81-87
• /
• 2009

Recently, extruded aluminium-alloy panels have been used in the car bodies for the purpose of the light-weight of railway vehicles and FSW(Friction Stir Welding), which is superior to the arc weldings, has been applied in the railway vehicles. This paper presents the optimum design of the FSW process on A6005 extruded alloy for railway vehicles to improve its mechanical properties. Rotational speed, welding speed and tilting angle of the tool tip were chosen as design parameters. Three objective functions were determined; maximizing the tensile strength, minimizing the hardness and maximizing the difference between the normalized tensile strength and hardness. The tensile tests and the hardness tests for fifteen FSW experiments were carried out according to the central composite design table. Recursive model functions on three characteristic values, such as the tensile strength, the hardness difference(${\Delta}Hv$) and the difference of normalized tensile strength and ${\Delta}Hv$, were estimated according to the classical response surface analysis methodology. The reliability of each recursive function was verified by F-test using the analysis of variance table. Sensitivity analysis on each characteristic value was done. Finally, the optimum values of three design parameters were found using Sequential Quadratic Programming algorithm.

• 대한기계학회논문집
• /
• 제16권8호
• /
• pp.1503-1512
• /
• 1992

본 연구에서는 열화평가 및 수명예측에 있어서 가장 중요한 문제로 대두되는 기계구조물의 사용시간과 부식 정도에 대한 관계 곡선을 규명하기 위하여 실험실의 가혹 환경하에서 부식을 시키면서 표면을 측정한 데이터로 통계적인 파라메타(parame- ter)를 추정하여, 인공부식시킨 부식재로 피로 강도를 평가하고, 또 부식된 구조물의 잔존수명을 예측할 수 있는 하나의 방법을 제시하고저 한다.

• Tribology and Lubricants
• /
• 제28권1호
• /
• pp.1-6
• /
• 2012

In this paper, a three elastic body sliding contact problem is modeled to investigate more precise wear mechanisms related with the sealing surface. A 3-D finite element contact model, a small spherical elastic particle, PTFE seal and steel surface, is solved using a nonlinear finite element code MARC. The deformed seal and steel surface shapes, von-Mises and principal stress distributions are obtained for different seal sliding distances. The entrapped small particle within PTFE seal results in very high stresses on the steel surface which exceeded its yield strength and produce plastic deformation such as groove and torus. The sealing surface could also be worn down by sub-surface fatigue due to intervening small particles together with the well-known abrasive wear. Therefore the proposed contact model adopted in this paper can be applied in design of various sealing systems, and further studies are required.

• 콘크리트학회논문집
• /
• 제24권4호
• /
• pp.415-422
• /
• 2012

이 연구에서는 FRP 부재를 이용한 표면매입 보강에서, FRP의 부착강도를 평가하기 위하여 총 78개의 기존실험 결과를 분석하고, 기존 연구자들에 의해 제안된 식들을 평가하였다. 그 결과 FRP부재의 형상계수(폭-두께비)와 강성을 반영한 Seracino의 식이 부착내력을 가장 근사하게 예측하는 것으로 나타났다. 그러나 Seracino의 식은 실험 결과를 다소 과소평가하는 양상을 보이고 특히 부착길이가 작을수록 그 경향이 두드러진 것으로 나타났다. 이는 부착길이 증가에 따른 영향이 Seracino의 식에는 전혀 반영되어있지 않기 때문으로 볼 수 있다. 기존 실험 결과의 분석을 통하여 부착길이와 강도와의 상관관계를 찾고 또한 여러 개의 FRP부재를 인접하여 배치시 발생하는 무리효과를 고려하여 Seracino 식을 수정 제안하였다. 이 제시된 식을 이용하여 기존 실험체에 대한 내력을 계산하고 평가한 결과, 제안된 식으로서 표면매입 보강된 FRP의 부착강도를 매우 근사하게 예측할 수 있는 것으로 나타났다.