• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.5
• /
• pp.980-986
• /
• 2007

Boundary scan test structure(JTAG IEEE 1149.1 standard) that supports an internal scan chain is generally being used to test CUT(circuit under test). Since the internal scan chain can only have a single scan-in port and a single scan-out port; however, existing boundary test methods can not be used when multiple scan chains are present in CUT. Those chains must be stitched to form a single scan chain as shown in this paper. We propose an efficient boundary scan test structure that adds a circuit called Clock Group Register(CGR) for multiple clocks testing within the design of multiple scan chains. The proposed CGR has the function of grouping clocks. By adding CGR to a previously existing boundary scan design, the design is modified. This revised scan design overcomes the limitation of supporting a single scan-in port and out port, and it bolsters multiple scan-in ports and out ports. Through our experiments, the effectiveness of CGR is proved. With this, it is possible to test more complicated designs that have high density with a little effort. Furthermore, it will also benefit in designing those complicated circuits.

• Journal of Korean Society for Geospatial Information Science
• /
• v.18 no.4
• /
• pp.87-92
• /
• 2010

With recent localized heavy rain, the collapsing accident of the cut slopes occur repeatedly every year. The maintenance of the cut slopes is very crucial as the collapsing of cut slopes causes various calamities such as human causalities and sweeping away of the roads. By looking at the study of current situation of the cut slopes, designed for maintenance of cut slopes, the locations of the damaged districts are hard to figure out as they are represented through distance mark and longitude and latitude. In this paper has used NDGPS methods and VRS service through GPS signal corrections that are received by DGPS standard department to correctly analyze the exact location and the shape of the slope. The result of this analysis shows that both methods produce similar shape of the slope. Therefore, these two methods, NDGPS methods and VRS service, can be applied to other analysis of cut slopes in different areas.

• The KSFM Journal of Fluid Machinery
• /
• v.2 no.3 s.4
• /
• pp.45-51
• /
• 1999

Centrifugal fans are widely used and the noise generated by these machines causes one of the most serious problems. In general, the centrifugal fan noise is often dominated by tones at BPF(blade passage frequency) and its higher harmonics. This is a consequence of the strong interaction between the flow discharged from the impeller and the cutoff in the casing. However, only a few researches have been carried out on predicting the noise due to the difficulty in obtaining detailed information about the flow field and casing effects on noise radiation. The objective of this study is to develop a prediction method for the unsteady flow field and the acoustic pressure field of a centrifugal fan and to calculate the effects of rotating velocity, flow rate, cut-off distance and the number of blades and its effects on the noise of the fan. We assume that the impeller rotates with a constant angular velocity and the flow field around the impeller is incompressible and inviscid. So, a discrete vortex method (DVM) is used to model the centrifugal fan and to calculate the flow field. The force of each element on the blade is calculated with the unsteady Bernoulli equation. Lowson's method is used to predict the acoustic source. The cut-off distance is the most important factor effecting the noise generation. Acoustic pressure is proportional to 2.8, which shows the same scaling index as the experimental result. In this paper, the cut-off distance is found to be the dominant parameter offecting the acoustic pressure.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.10
• /
• pp.4328-4336
• /
• 2011

The aim of this study is to find changes of the attributes that influence the purchase of cut roses during recent five years(2007~2011) and suggest some implications on ways to promote cut roses marketing. For this purpose, a survey was conducted through the Internet among 1,100 randomly chosen people living in Seoul, Inchon and Gyeonggi Province in 2011. A total of 1,023 valid replies were received for the analysis of the survey which was carried out by the subsidiary consulting firm. The survey panels and estimation models to analyze changes of consumers' preference attributes during recent five years are same to them of Kim, et al.(2007). That is, empirical analysis tools such as ordered probit model, multinomial logit model, and conjoint analysis were used according to Kim, et al.(2007). This paper suggests several policy implications to set up the target market of cut roses and marketing mix strategy to specify the best 4P(product, price, place and promotion).

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.4
• /
• pp.604-610
• /
• 1989

This paper is concerned with the machinability of fine ceramics(Al$_{2}$O$_{3}$) by using sintered diamond tools. For this purpose, ceramics cutting experiments under various cutting conditions such as cutting speed, feed rate, and others were carried out. The main results are follows : (1) During the cutting of fine ceramics, the used tools were found to be slightly chattering at cutting speed of 70m/min, and at cutting speed of higher than this I found the fine ceramics difficult to be cut. (2) When I used a tool with large nose radius, there occured a small amount of wear on the flank of the tool. However, at the early stage of fine ceramics cutting, the tools with smaller nose radii were required mainly to prevent the chipping of the ceramics. (3) When the materials were dry-cut, the appropriate cutting speel was found to be lower than 40m/min, and when the materials were dry-cut, I could cut them without any difficulty even at the speed of 70m/min, the surface roughness of ceramics cut at the speed of 70m/min was considerly fine. (4) It is generally believed that the principal cutting force is the largest in the case of steels cutting, but I found the thrust cutting force to be larger than any other cutting forces in the case of ceramics cutting.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.5
• /
• pp.101-106
• /
• 2006

This paper describes performance design of a solid rocket motor on which thrust cut-off system is installed, and evaluates performance of a rocket motor according to a size of TCO ports. TCO system installed on motors was made to carry out firing tests, and the trend of thrust due to various sizes of TCO port was analyzed to find the existence of the port size for maximum reversal thrust. Conservation equations were used to design performance of motors and to analyze test results. This technique for performance design will be usefully applied to the design of similar TCO systems.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.05a
• /
• pp.53-56
• /
• 2006

This paper describes performance design of a solid rocket motor on which thrust cut-off system is installed, and evaluates performance of a rocket motor according to a size of TCO ports. TCO system installed on motors was made to carry out firing tests, and the trend of thrust due to various sizes of TCO port was analyzed to find the existence of the port size for maximum reversal thrust. Conservation equations were used to design performance of motors and to analyze test results. This technique for performance design will be usefully applied to the design of similar TCO systems.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.878-883
• /
• 2005

This paper describes the effect of acid rock drainage(ARD) produced from the cut slope on the slope structures. Acid rock drainage is originated from a rock quarry located in coal mine zone and mineralization belt of Chosen Supergroup and Ogcheon group, andesite with the pyrite, and acid sulfate soils of Tertiary in Korea. The cut slope, where acid rock drainage comes out, almost has been constructed by shotcrete and planting works. According to the field observation results, in most cases, the acid rock drainage has an adverse effect on slope structures. The shotcrete, anchors and rock bolts produced corrosive action, and bad germination and growth diseases of covering plants of the slope planting construction due to ARD.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.6
• /
• pp.714-719
• /
• 2011

The surface roughness depending on the machining method is very important because is produce a finished product through riveting, sealing, bonding, and special paint in order to curb the turbulence and air resistance which occur between the sheets. Aluminum alloy 2024 which is widely used for interior and exterior material of aircraft are tested. Jin-young JW-60C wire cutting machine was used in this experiment. In this paper, the experimental investigation has been performed to find out the influence of the surface roughness and surface shape characteristics on the wire-cut EDM of discharge energy in aluminium alloy 2024. The selected experimental parameters are peak current, no-load voltage, off time and feed rate. The experimental results give the guideline for selecting reasonable machining parameters. The high discharge energy on the idle time, almost no change in surface roughness can be seen.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38C no.7
• /
• pp.563-572
• /
• 2013

Based on this paper, in case of the on-line account system in finance industry temporarily stops working because of the on-line data change from 00:00 to 00:30, it conducts in extra placement server and the director update is carried out via center cut or on-line server to make the service possible through customer director reproduction revision. So, from the simulation result in financial operating system, We retain the batch director & backup director securely about the important time data in each account classes on-line director without even one second interruption.