• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2008년도 하계종합학술대회
• /
• pp.515-516
• /
• 2008

We studied about new module technology to solve warpage problems that produce bending of cell in the LCD (Liquid crystal display). Characteristics of cell gap and glass bending of applying heat Panel's PAD part and cell at various temperature was investigated. When applies heat and compresses PAD party only in case of compressing COG(Chip on Glass), uniformity of cell gap that happen by glass bending by temperature of these compressing COG in the PAD party is decreased.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1999년도 추계종합학술대회 논문집
• /
• pp.181-184
• /
• 1999

This paper presents the accurate deembeding method for pad and parasitics of MOSFET device. rad effects are deembedded using THRU LINE, which is much simpler method without laborious fitting procedure compared with conventional OPEN and SHORT pad modeling. Parasitic resistance extraction uses the algebraic relation between increments of inversion layer charge and oxide capacitance. It is especially adequate for insulating gate junction device. Extracted parasitics are verified through comparing modeled and measured S parameters.

• 한국신뢰성학회:학술대회논문집
• /
• 한국신뢰성학회 2011년도 춘계학술발표대회 논문집
• /
• pp.49-54
• /
• 2011

반도체 칩과 패키지는 wire로 연결되는데, 이 때 반도체의 용도에 따라 다양한 wire와 pad의 조합이 사용되며, 이 두 개의 다른 금속물질 결합부위는 IMC(Inter Metallic Compound)를 형성하게 된다. 그러나, 결함 및 오염 등에 의하여 인접재료의 원자들이 이동하는 확산(Diffusion)이 발생하게 되어 IMC가 성장하고, 두 개의 금속물질간의 확산율은 상호 다르며, 확산율은 온도에 따른 함수가 된다. Au wire와 Ag pad를 이용하여 제조한 IR 수신모듈를 대상으로 3가지 고온조건에서 가속수명시험을 실시하였고, 각 온도별 수명분포를 바탕으로 가속계수와 활성화에너지 도출 및 정상온도에서의 수명도 예측할 수 있었다.

• 한국통신학회:학술대회논문집
• /
• 한국통신학회 1991년도 추계종합학술발표회논문집
• /
• pp.100-102
• /
• 1991

In this paper, we use LFSR(Linear Feedback Shift Register) as a kind of pseudo-random one-time pad. Key generator is constructed using r separate LFSR's with IP(Irreducible Polynominal) which are relatively prime. Key generated in this method has high linear complexity. And also, file cryptosystem for file encryption and decryption is constructed.

• Tribology and Lubricants
• /
• 제8권2호
• /
• pp.73-79
• /
• 1992

The pressure distribution between the piston pad and the cylinder wall is analyzed to reduce the friction and to get the dynamic stability in the low friction piston. The calculated results indicate that the rectangular pad may reduce the friction in comparison to the square one. And the low friction piston can be stabilized when the pressure difference between the top and bottom of the piston skirt is very small.

• 대한미세수술학회:학술대회논문집
• /
• 대한미세수술학회 1997년도 제17차 학술대회
• /
• pp.133-134
• /
• 1997

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제33회 춘계학술대회 개최
• /
• pp.236-242
• /
• 2001

In this paper the effect of bump compliance, load, and the number of pad on the lift-off speed is studied. When the load is greater and bump compliance lower, the shaft is lifted off at higher rotating speed. And when the load is applied near the center of pad, lift-off speed is lower. When the number of pad increases, the lift-off speed is higher. The lift-off characteristics can be used to lengthen the life time of the coating and design the rotating machinery supported by bump bearings.

• 한국수학사학회지
• /
• 제21권2호
• /
• pp.71-80
• /
• 2008

본 논문은 기하 프로그램 GSP(Geometer's SkechPad)를 응용하여, 수학이 흥미롭고 재미있는 교과목이며, 또 다양한 영역 속에서 아름답게 활용될 수 있는 것을 보이고자, 테셀레이션의 도형을 평면기하에서 평행이동, 미끄럼반사 등으로 우리 고유의 독특한 태극무늬와 단청문양, 흉배에 사용하였던 구름무늬 등을 현대적인 감각으로 디자인 한 것을 GSP(Geometr's SkechPad) 4.0 으로 작도하였다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 춘계학술대회 논문집
• /
• pp.1230-1235
• /
• 2011

The track stiffness is determined by the pad stiffness. Low elastic pad is the most effective track component on the basis of stress-displacement characteristics, dynamic response and fatigue characteristics. It is more important in case of concrete track. The main objective of this paper is to confirm the reduction effect of train load, which transfer to roadbed through track. To achieve this object, numerical analysis and real scale repeated loading test was performed. The load reduction effect of low elastic pad was analyzed by using displacement, stress and strain ratio of the paved track at each point.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제16권1호
• /
• pp.29-32
• /
• 1994

IN 1956, Peer presented a very comprehensive account of free fatty tissue transplantation. The use of buccal fat pad had been usually used to reconstruct the perioral defects. The buccal fat pad is a special fatty tissue which is markedly different from subcutaneous fat. And it is a easily accessible fat tissue in oral and maxillofacial region. The buccal fat pad can be used as a free graft or pedicled flap. Recently, buccal fat pad is interested in cosmetic surgery because its' removal for cosmetic purpose has been favorable result. We used the buccal fat as an unlined, pedicled graft for closure of large oroantral fistula. We present a case of report and review of literature.