• Journal of radiological science and technology
• /
• v.42 no.4
• /
• pp.265-270
• /
• 2019

Mammography is the most useful test for the early diagnosis of breast cancer. The MammoPad can be used for the purpose of reducing the pain felt by the patient due to the pressure of the breast. MammoPad cushion the pressure between the breasts and the equipment and reduce the patient's discomfort. A new material pad was fabricated to solve the problem of the H-pad which is currently in circulation. Quantitative evaluation of SNR and CNR and qualitative evaluation of imitation lesion using ACR Phantom were performed. In the quantitative evaluation, SNR and CNR of Non pad and Filter pad were not statistically significant.(p>0.05) In the qualitative evaluation, Fiber and Imitation lesion of H-pad and Filter pad were statistically significant(p<0.05), and all values of Calcification and Mass were not statistically significant. (p>0.05) In addition, Fiber, calcification, mass, and imitation lesion were not statistically significant in both Non pad and Filter pad.(p>0.05) Through this study, it was confirmed that the newly created Filter pad minimizes image quality degradation and can replace existing products.

• Tribology and Lubricants
• /
• v.40 no.2
• /
• pp.67-70
• /
• 2024

Chemical mechanical planarization (CMP) is an essential process for ensuring high integration when manufacturing semiconductor devices. CMP mainly requires the use of polyurethane-based polishing pads as an ultraprecise process to achieve mechanical material removal and the required chemical reactions. A diamond disk performs pad conditioning to remove processing residues on the pad surface and maintain sufficient surface roughness during CMP. However, the diamond grits attached to the disk cause uneven wear of the pad, leading to the poor uniformity of material removal during CMP. This study investigates the pad wear rate profile according to the swing motion of the conditioner during swing-arm-type CMP conditioning using deep learning. During conditioning, the motion of the swing arm is independently controlled in eight zones of the same pad radius. The experiment includes six swingmotion conditions to obtain actual data on the pad wear rate profile, and deep learning learns the pad wear rate profile obtained in the experiment. The absolute average error rate between the experimental values and learning results is 0.01%. This finding confirms that the experimental results can be well represented by learning. Pad wear rate profile prediction using the learning results reveals good agreement between the predicted and experimental values.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 1999.10c
• /
• pp.399-404
• /
• 1999

This study were performed to find the cooling effect and to provide design data during summer season for the Pad& Fan system of greenhouse . The temperature variation along the greenhouse width were analyzed. Also, the effect of the pad location and fan capacity on the cooling of the greenhouse were analyzed. While Pad &Fan systems were operating the temperatures in greenhouse were very different along the meausring locations. It is recommeded that PAD location and FAN capacity should be considered to design the Fan and Pad system in order to provide greenhouse the optimum temperature condition.

• Journal of the Microelectronics and Packaging Society
• /
• v.22 no.3
• /
• pp.51-56
• /
• 2015

It has been used various pad finish materials to enhance the reliability of solder joint and recently Electroless Ni Electroless Pd Immersion Gold (the following : ENEPIG) pad has been used more than others. This study is about reliability according to being used in commercial Electrolytic Ni pad and ENEPIG pad, and was observed behavior of various Cu contents. After reflow, the inter-metallic compound (IMC) between solder and pad is composed of $Cu_6Sn_5$ (Ni substituted) by using EDS, and in case of ENEPIG, between IMC and Ni layer was observed the dark layer ($Ni_3P$ layer). Additional, it could be controlled the thickness of dark layer according to Cu contents. Investigated the different fracture mode between electrolytic Ni and ENEPIG pad after drop shock test, in case of soft Ni, accelerated stress propagated along the interface between $1^{st}$ IMC and $2^{nd}$ IMC, and in case of ENEPIG pad, accelerated stress propagated along the weaken surface such as dark layer. The unstable interface exists through IMC, pad material and solder bulk by the lattice mismatch, so that the thermal and physical stress due to the continuous exterior impact is transferred to the IMC interface. Therefore, it is strongly requested to control solder morphology, IMC shape and thickness to improve the solder reliability.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.17 no.2
• /
• pp.132-141
• /
• 1992

The CCITT recommendation X.3, X.20, X.29 and X.25 protocols have been efficiently used in subscriber site for the purpose of using existing C DTE In the ISDN. The Packet Assem-bly /Disasembly (PAD) which covers these protocols can connect C_DTE to the PSDN. The number of C DTE connected to the PAI) Is dependent on the PAD performance. The design of the Traffic Generator (TG) S/W which can measure the PAD performance Is Introduced In this paper.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.4
• /
• pp.303-307
• /
• 2007

This paper investigated the effect of the pad buffing process on the material removal characteristics and pad stabilization during silicon chemical mechanical polishing. The pads surface were controlled by the buffing process using a buffer made by the sandpaper. The buffing process is based on abrasive machining by using a high speed sandpaper. The controlled pad by the buffing process show less deformation deviation and stable material removal rate during the CMP process. In addition, the controlled pad ensure better uniformity of removal rate than comparative pads. As a result of monitoring, the controlled pad by the buffing process demonstrated constant and stable friction force signals from initial polishing stage. Therefore, the tufting process could control the pad surface to be uniform and improve the performance of the polishing pad.

• Tribology and Lubricants
• /
• v.14 no.1
• /
• pp.7-13
• /
• 1998

The static characteristics of a five-pad tilting pad journal bearing of load on pad (LOP) type have been investigated experimentally under the different values of bearing load and shaft speed. The diameter and length of the bearing are 300.91 mrn and 149.8 mm, reslx;ctively. Circumferential distribution of the film pressure, film thickness, journal surface temperature and beating surface temperature are measured. A noticeable inlet pressure rise is observed at the entrance of each pad, especially the bottom pad. The inlet pressure is increased by the increase of shaft speed as well as bearing load. In the five-pad tilting pad joumal bearing of LOP type, almost all of beating load is being carried only by the bottom pad. The maximum bearing surface temperature is observed at near the minimum film thickness. It is observed that the metal temperature of the mid-plane is higher than that of the edge at the inlet region, while the metal temperature of the edge is higher than that of the mid-plane at the outlet region.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.6
• /
• pp.467-473
• /
• 2003

This paper describes the fluttering characteristics of the upper pad in a tilting pad journal bearing(6-pad, LOP type) using a steam turbine. In order to investigate the phenomena of the upper pad fluttering experimentally, the absolute vibration of the upper pads, the relative vibration between bearing and shaft and the circumferential distribution of the film thickness are measured under the different values of supply oil flow rate, shaft speed and bearing load. It can be known that the fluttering mechanism of the upper pads has a tendency of the self-excited vibration from the study of fluttering frequencies and amplitudes with the change of shaft speed. Furthermore, it is observed that the incipient upper pad fluttering velocity is increased by the increase of oil supply flow rate and the fluttering amplitude of the upper pads is increased by the decrease of the ell flow rate and by the increase of the bearing load.

• The Research Journal of the Costume Culture
• /
• v.6 no.2
• /
• pp.66-76
• /
• 1998

In order to investigate the effect of shoulder pad affecting the arm movement, eleven women volunteers of standard body whose age is from eighteen to twenty-four(x±1σ) were chosen and this experiment had done according to front-vertical motion, side-vertical motion and horizontal motion of upper limps for tow different materials of shoulder pad(sponge, non-woven) and four different thickness of shoulder pad(0.6cm, 0.8cm, 1.2cm). On the base of this, this study, when putting on shoulder pad, try to find the reform method of shoulder part pattern. The results are as follows. 1. When puting on shoulder pad to blouse pattern to rise shoulder pad for rate of two-third per thickness is seemingly the best for sensory evaluation. So, when putting on shoulder pad, we understand that in order to improve sensory evaluation. So, when putting on shoulder pad, we understand that in order to improve sensory evaluation of clothes, when that, rising shoulder pad for ate of two-third per thickness is the best. 2. From the results of measure of functional volume and physiological value for functionality evaluation according to thickness and material, motion of shoulder pad, 1.2 cm thickness and non-woven material is evaluated the worst for functionality. 3. From the results of sensory evaluation and functionality evaluation of material of shoulder pad, sponge material is superior for functionality but not for sensory evaluation, non-woven material is superior for sensory evaluation non-woven material is superior for sensory evaluation but not for functionality. So, think that it had better use sponge material for functional clothes, non-woven material for aesthetical clothes. 4. From the results of functionality of clothes, when putting on shoulder pad, the worst discomfortable parts are the armpit part and the shawl part, functionality of these part shoulder be reformed.

• Fashion & Textile Research Journal
• /
• v.20 no.5
• /
• pp.569-582
• /
• 2018

The purpose of this study is to verify the impact protection performance and to evaluate the activity, design, fit, and pad characteristics of the fall impact protection clothing for elderly women. The protective clothing was designed as pants type and underwear type, and an impact protection pad in the form of a tightly connected regular hexagon piece was inserted in the hip and hip joints. The pad was made of two kinds of foam single pad and foam and gel combination pad so that they could be inserted into pants type and underwear type, respectively. The results of the shock absorption performance of the fall impact protective clothing showed that when the impact force of 4601N was applied to the pants type protective clothing, the impact force was reduced by 29% in the foam pad type and 26% in the gel and foam pad type. When the force of 5113N was applied to the underwear type, it decreased by 40% in the foam pad type and by 34% in the gel and foam pad type. As a result of wearing evaluation of subject group, it was found that fit and activity of underwear type was better than that of pants type. Foam pad type was evaluated to be lighter than gel and foam pad type in both the subject and the expert group and the gel and foam pad was evaluated to be more flexible in the expert group.