• 한국초전도학회:학술대회논문집
• /
• v.10
• /
• pp.230-235
• /
• 2000

The extrusion process for long-length multi-filaments of BSCCO 2223 superconductor tape has been investigated with aids of Finite Element Method and experimental inspection. Since the arrangement of filaments in matrix material has characteristic of rotational symmetry, a 2-dimensional commercial FEM package, DEFORM-2D, was adopted to simulate extrusion process with different variables such as hardness of sheath material, lengths of each filament and arrangement. From the FEM analysis, since the inner filaments move faster than the outer one, distribution of filaments is needed to be optimized. In the case of pure Ag matrix, undesirable non-uniform distribution of filament was obtained due to low hardness of sheath material. Dummy sample(brass (sheath) and talc powder(filament)), however, which has relatively high hardness of sheath material, had been produced with desirable results. Therefore, it is necessary to optimize hardness of sheath material, extrusion temperature and billet design.

• Transactions of Materials Processing
• /
• v.17 no.4
• /
• pp.249-256
• /
• 2008

Combined phase transformation and heat transfer was considered on the simulation of hot press forming process, using material properties modeler, $JMatPro^{(R)}$ and a finite element package, $DEFORM^{TM}$-HT. In order to obtain high temperature mechanical properties and flow curves for different phases, a material properties modeler, $JMatPro^{(R)}$ was used, avoiding expensive and extensive high temperature materials tests. The results successfully show that the strength of hot press forming parts may exhibit different strength in the same parts, depending on the contact of blank with tooling. It was also shown effectively that the strength of the parts can be controlled by designing appropriate cooling paths and coolants. This was shown in terms of different heat convection coefficient in the calculation. Overall, current combination of software was shown to be an effective tool for the tool and process design of hot forming process, although the material modeler needs to be additionally verified by an appropriate set of high temperature materials test.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.4
• /
• pp.376-380
• /
• 2008

The optical properties of multi layered thin films with $Sb_2O_3/Na_3AlF_6/Sb_2O_3/Cr$ were simulated by using EMP(Essential Macleod Program). EMP is a comprehensive software package to design and analyse the optical characteristics of multi-layered thin film. $Sb_2O_3$ and $Na_3AlF_6$ were selected as a high refractive index and low refractive index material respectively. Additionally Cr was chosen as mid reflective material. Optical properties including color effect were systematically studied in terms of different optical thickness of low refractive index material. The optical thickness of $Na_3AlF_6$ was changed as 0.25, 0.5, 0.75 and $1.0\lambda$. The film with 0.25, 0.5, 0.75 and $1.0\lambda$ of optical thickness showed mixed color range between purple and red range, yellowish green and bluish green, purple and mixed color range of green and purple respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.345-345
• /
• 2007

ZnS/$Na_3AlF_6$/ZnS/Cu multi-layered thin film were simulated by EMP. EMP is a comprehensive software package for the design and analysis of optical thin film. ZnS and $Na_3AlF_6$ was selected as a high refractive index material and low refractive index material And Cu was selected as mid reflective material. Optical properties including color effect were systematically studied in terms of different low refractive index materials thickness. $Na_3AlF_6$ were changed 0.25, 0.5, 0.75, $1.0{\lambda}$. The thin film showed $0.25{\lambda}$ : blue, purple / $0.5{\lambda}$ : yellow $0.75{\lambda}$ : blue, purple, red / $1.0{\lambda}$ : yellow, green, blue, purple. It was becaused by different optical thickness of $Na_3AlF_6$. The maximum of optical interference by refractive layer.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2003.09a
• /
• pp.3-17
• /
• 2003

.Package Trend -> Memory : Lighter, Thinner, Smaller & High Density => SiP, 3D Stack -> MPU : High Pin Counts & Multi-functional => FCBGA .Interposer Trend -> Via - Unfilled Via => Filled Via - Staggered Via => Stacked Via -> Emergence of All-layer Build-up Processes -> Interposer Material Requirement => Low CTE, Low $D_{k}$, Low $D_{f}$, Halogen-free .New Technology Concept -> Embedded Passives, Imprint, MLTS, BBUL etc.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.11a
• /
• pp.186-192
• /
• 2000

The heat generated in contact type braking system can cause an unacceptable braking performance. Thermal behavior of ventilated disk brake system is presented in this paper. The temperature and velocity fields of 3-D unsteady simulated model are obtained using a software package "FLUENT". The numerical results show that there exits a temperature nonuniformity between the disk faces contacting with pads. The conduction rate through the disk and pad is calculated and the effect of material conductivity is also investigated.estigated.

• Advances in Computational Design
• /
• v.4 no.3
• /
• pp.211-221
• /
• 2019

Numerical modeling of reinforced concrete structures is a difficult engineering problem, primarily because of the material inhomogeneity. The behaviour of a concrete element with reinforcement can be analyzed using, for example, the Barcelona model, which according to the literature, is one of the most suitable models for this purpose. This article compares the experimental data obtained for an orthotropic concrete slab band system with those predicted numerically using Concrete Damage Plasticity model. Abaqus package was used to perform the calculations.

• Fashion & Textile Research Journal
• /
• v.18 no.2
• /
• pp.184-193
• /
• 2016

This study investigates the recognition and preference of functional textile material about outdoor clothing widely used in the current fashion market. The study targeted 216 males and females in their 20s to 50s who wear outdoor clothing as casual wear. To analyze data, frequency analysis, cross tabulation analysis and ANOVA were conducted with the SPSS 21.0 statistical package. The results are as follows. First, recognition of functional textile material of outdoor clothing showed that 20s was the lowest preference and all age groups preferred lightweight textile material. In information recognition of functional outdoor clothing, 40s showed the highest recognition, while 20s showed the lowest recognition. Second, 40s and 50s preferred functional material to 20s and 30s. In particular, 40s and 50s preferred clothing items with water vapor permeability & water repellent material to 20s and 30s. All age groups preferred insulation material jumpers, water vapor permeability & water repellent material jumpers and stretch pants. Third, reasons for purchasing functional material clothing was: design for the age group 20s and 30s versus health and function for the age group 40s and 50s. It is necessary to develop functional clothing products based on exact consumer information and preferences.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.2
• /
• pp.61-66
• /
• 2010

A virtual manufacturing system that is composed of JMatPro, a material modeler and $DEFORM^{TM}$-HT, a finite element package is applied to the hot press forming process: high temperature material properties for each phase such as flow stress, elastic modulus, Poisson's ratio, thermal expansion coefficient, in addition to TTT curve are predicted by JMatPro and taken into $DEFORM^{TM}$-HT to predict the material behavior considering phase transformation and heat transfer simultaneously. In order to verify the accuracy of computation, the residual stress and the springback were compared with the experimental measurements. Both the predicted and measured principal residual stresses and amount of springback were in good agreement. It was also found that the residual stresses generated from hot press forming are not negligible as it has been generally assumed, although the springback deformation is quite small.

• Journal of Biosystems Engineering
• /
• v.30 no.6 s.113
• /
• pp.347-353
• /
• 2005

Paper angle, environment friendly packaging material, has been mainly used as an edge protector, But, in the future, paper angle will be applied to package design of heavy product such as strength reinforcement or unit load system (ULS). Therefore. understanding of buckling behavior fur angle itself, compression strength and quality standard are required. The objectives of this study were to characterize the buckling behavior by theoretical and finite element analysis, and to develop compression strength model by compression test for symetric and asymetric paper angle. Based on the result of theoretical and finite element analysis, as applied load level was bigger and/or the length of angle was longer, incresing rate of buckling of asymmetric paper angle was higher than that of symmetric paper angle. Decreasing rate of minimum principal moment of inertia significantly increased as the extent of asymmetric angle increased, and buckling orientation of angle was open- direction near the small web. Incresing rate of maximum compression strength (MCS) for thickness of angle decreased as the web size increased in symmetric angle. MCS of asymmetric angle of 43${\times}$57 and 33${\times}$67 decreased $15{\~}18\%$ and $65{\~}78\%$, and change of buckling increased $12{\~}13\%$ and $62{\~}66\%$, respectively.