• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.2
• /
• pp.55-62
• /
• 1992

Polycrystalline silicon ingots were manufactured using the casting method for polycrystalline silicon solar cells. These ingots were cut into wafers and ten n$^{+}$p type solar cells were made through the following simple process` surface etching, n$^{+}$p junction formation, metalization and annealing. For the grain boundary passivation, the samples were oxidized in O$_2$ for 5 min. at 80$0^{\circ}C$ prior to diffusion in Ar for 100 min. at 95$0^{\circ}C$. The conversion efficiency of polycrystalline silicon solar cells made from these wafers showed about 70-80% of those of the single crystalline silicon solar cell and superior conversion efficiency, compared to those of commercial polycrystalline wafers of Wacker Chemie. The maximum conversion efficiency of our wafers was indicated about 8%(without AR coating) in spite of such a simple fabrication method.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.8
• /
• pp.721-728
• /
• 2017

High-grade gray cast iron (HCI350) was prepared by adding Cr, Mo and Cu to the gray cast iron (GC300). Their microstructure, mechanical properties and fatigue strength were studied. Cast iron was made from round bar and plate-type castings, and was cut and polished to measure the percentage of each microstructure. The size of flake graphite decreased due to additives, while the structure of high density pearlite increased in volume percentage improving the tensile strength and fatigue strength. Based on the fatigue life data obtained from the fatigue test results, the probability - stress - life (P-S-N) curve was calculated using the 2-parameter Weibull distribution to which the maximum likelihood method was applied. The P-S-N curve showed that the fatigue strength of HCI350 was significantly improved and the dispersion of life data was lower than that of GC300. However, the fatigue life according to fatigue stress alleviation increased further. Data for reliability life design was presented by quantitatively showing the allowable stress value for the required life cycle number using the calculated P-S-N curve.

• Journal of Korean Foot and Ankle Society
• /
• v.23 no.3
• /
• pp.105-109
• /
• 2019

Purpose: To compare the efficacy between cast immobilization and functional treatment using an ankle brace as a treatment for acute lateral ankle sprain. Materials and Methods: This study reviewed the medical records of 157 acute ankle sprain patients who were treated between 2009 and 2014. A total of 101 cases were included in this study except for cases with a combined injury, and could not be followed up for eight weeks after the first visit. The patients were divided according to the treatment modality: a cast immobilization group (64 cases) and functional treatment group (37 cases). The clinical outcomes were assessed retrospectively based on the medical records of each group. The residual symptoms, such as pain, swelling, and instability, at three weeks after the primary treatment and at the last visit were compared. Results: The residual pain and instability were significantly common in the functional treatment group at three weeks. Five cases (7.8%) of pain and one case (1.6%) of instability were in the cast group whereas nine cases (24.3%) of pain and six cases (16.2%) of instability in functional treatment group (p=0.021, p=0.014). On the other hand, there was no meaningful difference at the last follow-up. Residual pain, swelling, and instability at the last visit were noted in three (4.7%), six (9.4%), and four cases (6.3%) in the cast group, and three (8.1%), three (8.1%), and three (8.1%) were observed in the functional treatment group. Six patients refused cast immobilization. Conclusion: Although there was no significant difference at the last follow-up, cast immobilization appears to be more effective than a functional brace in terms of early pain relief and early restoration of ankle stability as a treatment for acute ankle lateral sprain in this study.

• The Journal of Korean Academy of Prosthodontics
• /
• v.28 no.2
• /
• pp.165-174
• /
• 1990

The purpose of the study was to correlate margin design(chamfer, shoulder, shoulder with a $45^{\circ}$ bevel. with the seating and sealing of cemented full cast crowns under standardized simulated clinical conditions. Wax patterns were made with milled stainless-steel dies and rings, and were invested, burnt out, and cast. The full cast crowns were comented on individual resin dies, and a gradually diminishing load(45kg to 25kg. was applied over a 10-minute period. The specimens were sectioned centrally with a low speed diamond saw and examined with light microscope. The results were as follows : 1. Chamfer preparations demonstrated it was the best marginal seal, followed in order by the shoulder with a $45^{\circ}$ bevel, and by the shoulder(p<.05). 2. Chamfer preparations demonstrated it was the best occlusal seating, followed in order by the shoulder, and by the shoulder with a $45^{\circ}$ bevel(p<.05).

• The Journal of Advanced Prosthodontics
• /
• v.4 no.2
• /
• pp.89-92
• /
• 2012

PURPOSE. Adequate passive-fitting of one-piece cast 3-element implant-supported frameworks is hard to achieve. This short communication aims to present an alternative method for section of one-piece cast frameworks and for casting implant-supported frameworks. MATERIALS AND METHODS. Three-unit implant-supported nickel-chromium (Ni-Cr) frameworks were tested for vertical misfit (n = 6). The frameworks were cast as one-piece (Group A) and later transversally sectioned through a diagonal axis (Group B) and compared to frameworks that were cast diagonally separated (Group C). All separated frameworks were laser welded. Only one side of the frameworks was screwed. RESULTS. The results on the tightened side were significantly lower in Group C ($6.43{\pm}3.24{\mu}m$) when compared to Groups A ($16.50{\pm}7.55{\mu}m$) and B ($16.27{\pm}1.71{\mu}m$) ($P$ <.05). On the opposite side, the diagonal section of the one-piece castings for laser welding showed significant improvement in the levels of misfit of the frameworks (Group A, $58.66{\pm}14.30{\mu}m$; Group B, $39.48{\pm}12.03{\mu}m$; Group C, $23.13{\pm}8.24{\mu}m$) ($P$ <.05). CONCLUSION. Casting diagonally sectioned frameworks lowers the misfit levels. Lower misfit levels for the frameworks can be achieved by diagonally sectioning one-piece frameworks.

• The Journal of Korean Academy of Prosthodontics
• /
• v.38 no.2
• /
• pp.169-177
• /
• 2000

The purpose of this study was to compare the retention of complete cast crown over amalgam ores, composite resin cores, and cast gold cores when cemented with three different luting agents. Eighteen core specimens each of amalgam(Bestaloy, Dong Myung, Seoul, Korea), composite resin (Z100, 3M Dental product, st. Paul, Minn) and type IV gold alloy (Ba-4, Heesung Engelhard Corp., Korea) were made in a customized milling stainless steel die. A wax pattern with a loop attached to occlusal surface was made for each core and a type II gold alloy casting was fabricated. The castings which had clinically acceptable marginal fit were used as test samples. The following luting cements were used to cement cast crowns on each core material : (1) zinc phosphate cement (Confi-dental Products Co., USA) (2) glass-ionomer cement (Fuji Plus, GC Industrial Corp., Tokyo, Japan) (3) resin cement (Panavia 21, Kuraray Co., USA). All cements were mixed according to manufacturers' instructions. A static load of 5kg was then applied for 10 minutes on the crowns. All specimens were stored in saline solution for 24 hours at $37^{\circ}C$ and thermocycled for 500 cycles. After storage and cycling, the tensile bond strengths were measured by using a universal testing machine (Instron Corp., Canton, Mass.) at a crosshead speed of 0.5mm/min. The results were as follows 1. The retentive strength of resin cement was the highest of alt three types of cement for resin core (p<0.05). 2. There was no statistical difference among the retentive strengths of three cements for amalgam core (p>0.05). 3. The retentive strength of resin cement was higher than that of zinc phosphate for cast core, but there was no difference between the retentive strength of glass ionomer cement and those of rein and zinc phosphate cement. 4. The retentive strength of the zinc phosphate cement for amalgam core was the highest of all type of cores.

• Restorative Dentistry and Endodontics
• /
• v.19 no.2
• /
• pp.473-484
• /
• 1994

To investigate the effect of resin cement, which had been known to increase the adhesive capacity of the cast gold inlay, on the gingival marginal fit and whether the tin-planting of the beveled area affects the marginal fit, Class II cast gold inlays were made on the 25 sound molars. Control group(ZPC goup) was cemented with the ZPC by conventional method. Experimental groups were cemented with the resin cement(Super-hond & $Panavia_{EX}$) and subdivided further by the existence or nonexistence of the tin-plating of the beveled area(ST & PT groups: with plating, SNT & PNT groups: without plating). So, each group was consisted of 5 teeth and the gingival margin of each specimen was mesiodistally sectioned by 3 times and the marginal and internal gap were evaluated by the Stereo Microscope (${\times}180$) and the Scanning Electron Micrascope(${\times}5,000$) was used for examining the adhesive relationship of the resin cement to the cavity wall and to the cast gold surface. The results were as follows : 1. Marginal gap was less than internal gap in all groups. 2. ZPC and SNT(bevel without tin-plating) groups showed the least gap and gap in PNT(bevel without tin-plating) group, ST(bevel with tin-plating) group, PT(bevel with tin-plating) group showed the greater value in order in evaluation of the both internal gap and marginal gap. 3. With the exception of the relationships between ZPC and SNT groups, ST and PNT groups, relationships between any other groups showed the statistical significance in the internal gap(p<0.05). 4. In the marginal gap, all relationships between groups showed the statistical significance (p<0.05) except the relationships between ZPC and SNT groups, ST and PNT groups, ZPC and PNT groups. 5. ZPC group showed more soluble phenamena than the resin groups(ST, SNT, PT, PNT). 6. Resin cement showed the void spaces in spite of good penetration into the micro-irregularities on both the tooth surface and the cast surface. The void was shown more in PT and PNT groups than in the ST and SNT groups. 7. After the treatment of heat and desiccation for SEM specimen, resin cements were detached more easily from the tooth surface than from the cast surface.

• Structural Engineering and Mechanics
• /
• v.82 no.1
• /
• pp.55-67
• /
• 2022

The precast reinforced concrete frame system is a method for industrialization of construction. However, the seismic performance factor of this structural system is not explicitly clarified in some existing building codes. In this paper, the seismic performance factor for the existing precast concrete building frame systems with cast-in-situ reinforced shear walls were evaluated. Nonlinear behavior of the precast beam-column joints and cast-in-situ reinforced shear walls were considered in the modeling of the structures. The ATC-19's coefficient method was used for calculating the seismic performance factor and the FEMA P-695's approach was adopted for evaluating the accuracy of the computed seismic performance factor. The results showed that the over-strength factor varies from 2 to 2.63 and the seismic performance factor (R factor) varies from 5.1 to 8.95 concerning the height of the structure. Also, it was proved that all of the examined buildings have adequate safety against the collapse at the MCE level of earthquake, so the validity of R factors was confirmed. The obtained incremental dynamic analysis (IDA) results indicated that the minimum adjusted collapse margin ratio (ACMR) of the precast buildings representing the seismic vulnerability of the structures approximately equaled to 2.7, and pass the requirements of FEMA P-695.

• Korean Journal of Organic Agriculture
• /
• v.22 no.1
• /
• pp.197-208
• /
• 2014

The present study was conducted to provide basic data for efficient vermicomposting of swine manure by investigating the effect of sawdust mix on growth and reproduction of earthworms, amount of earthworm cast produced, and its chemical composition when mixing swine manure in different levels (0(SSD0), 10(SSD10), 20(SSD20), 30(SSD30), and 40%(SSD40)) with sawdust commonly used as moist control in manure composting. The C/N ratio of the feed and the survival rate of earthworms for the SSD0 treatment (10.19, 35.2%), The C/N ratio of the feed was 11.09-16.44 and increased with higher level of sawdust mixed, and the survival rate of earthworms during the experiment period was 35.2-100%. The number of earthworms was 16.6 in the SSD40 treatment, and young worms were not found in the SSD0 treatment or the treatment with less than 30% sawdust in the mix. The number and the weight of cocoons in SSD30 and SSD40 treatments were found to be in the ranges of 23.8-59.8 and 256-660 mg respectively. The production of earthworm cast and digested amount were higher with the higher level of mixed sawdust (p<0.05), and the C/N ratio of cast increased with the mixed sawdust ratio, being significantly higher ratio in SSD30 and SSD40 than other treatments (p<0.05). Heavy metals content tended to decrease with the mixed sawdust level. To summarize, the higher level of mixed sawdust was associated with improvement in growth and reproduction of earthworms, and 30-40% sawdust mix in particular could result in efficient vermicomposting.

• The Journal of Korean Academy of Prosthodontics
• /
• v.8 no.1
• /
• pp.25-29
• /
• 1968

The purposes of this study were to measure the film thickness of zinc phosphate cement between the casting restorations and preparation walls. In addition, the differences between finger press and non press techniques after the castings were seated completely on the preparation by an automatic mallet until the cement set were studied. The results were as follows : 1) In full cast crown, the cement film thickness on the side wall was thinner than that on the other walls. 2) In 3/4 crown and inlay, the cement thickness was thinner than that in cast crowns. 3) The cement of great W/P ratio showed thinner thickness than that of little W/P ratio. 4) The continuous finger press after the castings were seated completely on the preparations had few influence on the cement film thickness.