• 한국토양비료학회지
• /
• 제44권5호
• /
• pp.688-695
• /
• 2011

우리나라 남부 이모작 논토양의 생산성향상을 위한 합리적인 관리책을 제시코자 영남지역 주요 논 토양별 경반층 생성특성 및 원인을 현지조사 중심으로 수행한 결과는 다음과 같다. 논 토양의 배수등급 및 토성에 따라 총 90필지의 경운실태를 조사한 결과, 경운시기는 대부분 춘경이었고 기종은 중대형 트랙터가 대종을 이루고 있었으며 경운방법은 토양 배수조건이 불량할수록 위탁경운을 하는 경향이었다. 경운깊이와 원추관입 최대저항값 출현깊이와는 고도의 상관을 보였고, 최대저항값 출현 토심은 약 27.1 cm로 조립질 토양에서 다소 깊은 경향으로 원추관입최대저항값은 2.50 Mpa으로 사질 및 사양질 토성이 3.46~3.29 Mpa로 높았고, 경반층의 강도는 세립질토양에서 뚜렷이 높았다. 경반형성 부위의 용적중은 $1.3{\sim}1.5g\;cm^{-3}$로 미사질계 토양이 낮았으며 고상율은 사양질이 미사질에 비해 높아 공극율은 낮은 경향을 보였다. 경반층 직하토층의 유기물, 유효인산, 치환성칼리 함량은 표토에 비해 매우 낮은 경향인 반면, pH와 치환성 석회 및 고토의 함량은 높은 경향이었다. 토층별 토양수분 함량과 원추관입저항값과는 관계는 표토는 부의 상관을 보인 반면 심토는 일정한 경향이 없었다. 경운여부에 따른 논토양 원추관입저항은 토심 20~23 cm에서 큰 차이를 보였고 경운답은 2.03~2.21Mpa인 반면, 무경운답은 1.18~1.25 Mpa로 낮았으며 무경 운 년수가 진행될수록 쟁기바닥층은 없어지는 반면, 토심10 cm 부위에 원추관입저항이 높은 토층이 새로 생성되었음. 따라서 남부 다모작지 논토양 견밀화 (경반화) 토층은 토심 15~20 cm 부위에서 주로 형성되었으며 농작업과 관련성이 높으며 작업 시 토양의 수분조건은 경반화에 크게 영향하며 경반이 생성된 토층의 투수력은 $0.03{\sim}0.14mL\;hr^{-1}$ 매우 낮아 양 수분의 수직이동에 영향을 미치는 것으로 나타났다.

• 농업생명과학연구
• /
• 제50권1호
• /
• pp.105-115
• /
• 2016

남부지역의 효율적인 삼나무 임분 관리방안을 마련하기 위하여 20m×20m 규모의 총 67개 조사구를 설치하였으며, 층위별 식생 및 임분구조 조사에 따른 군락유형 및 생장조사를 실시하였다. 군집분석을 실시한 결과 삼나무군락(C1)과 삼나무-편백군락으로 구분되었으며, 삼나무-편백군락은 다시 졸참-곰솔군락(C2), 졸참-편백군락(C3)으로 구분되었다. 교목층 삼나무의 중요치는 C1 97.2%, C2 80.7%, C3 47.6%로 유형간 차이가 나타났으며, 아교목층에는 C1 8.9%, C2 15.2%, C3 5.7%로 C2에서 가장 높게 나타났다. C3의 경우 아교목층에 솜대 및 이대가 나타나 이에 대한 관리가 필요한 것으로 사료된다. 관목층의 경우 C1 9.2%, C2 7.0% 이었으나, C3에서는 삼나무가 나타나지 않았다. 교목층의 종다양도는 C1이 0.059로 가장 낮았으며, C3에서 0.548로 가장 높았다. 우점도는 C1에서 0.958로 나타나 삼나무가 우점하는 것으로 나타났으며, C3은 우점도가 낮게 나타나(0.393) 다수의 종이 경쟁하고 있는 것으로 사료된다. 평균직경연년생장량은 7.01(C2)~8.04(C1)mm/yr의 범위로 나타났으며, 유형별 관리방안은 C1의 경우 경쟁목제거, 가지치기, 솎아베기가 적합하며, C2의 경우 경쟁수종 제거를 통한 삼나무 전형군으로의 유도 및 수하식재를 통한 타 수종으로의 갱신이 더욱 유리할 것으로 판단되었다.

• 한국해양학회지:바다
• /
• 제12권4호
• /
• pp.380-389
• /
• 2007

암반 해안의 해조 군락에 서식하는 저서무척추동물들에 의해서 이용되는 유기물의 기원을 밝히기 위하여 저서동물과 그들의 잠재 먹이원에 대한 탄소와 질소 안정동위원소 비($\delta^{13}C$ 및 $\delta^{15}N$)값 조성을 분석하였다. 조사는 부영양화된 반폐쇄성 내만인 남해안의 광양만 연안 암반 조간대와 상대적으로 빈영양의 외양에 노출된 환경 특성을 가지는 동해안의 대진(삼척)연안의 암반 조하대를 대상으로 2005년 5월부터 6월 사이에 실시되었다. 암반에서 노출되어 서식하는 부유물 섭식자들은 다른 섭식 양식을 가지는 동물군에 비해 상대적으로 낮은 $\delta^{13}C$ 값을 가져 이들이 식물플랑크톤에서 유래하는 유기물을 주로 이용하여 표영먹이망과 강한 영양연결을 가지는 것으로 나타났다. 반면, 암반틈 속에서 서식하는 일부 부유물 섭식자를 포함한 초식동물과 퇴적물 섭식자 및 육식성 포식자들은 상대적으로 높은 $\delta^{13}C$ 값을 가져 해조류에서 유래한 유기물을 주로 이용하여 저서먹이망을 형성하였다. 따라서 부유물 섭식자를 제외하고 해조 군락을 서식처로 하는 대부분의 동물들이 해조류에서 유래한 유기물을 이용하는 저서먹이망으로 강한 영양연결을 가져 연안 암반 생태계에서 생물생산과 생물 다양성의 유지에 대한 해조류의 중요성을 잘 나타내었다. 또한 광양만과 같은 부영양화된 연안에서 상대적으로 빈영양인 동해 연안 조하대의 저서동물과 해조류에 비하여 높은 $\delta^{15}N$ 값 분포는 육상으로부터 유입되는 영양염이 암반 조간대의 해조류 생산에 이용되고 이어서 이 특정 연안 생태계의 먹이망으로 편입되는 경로를 가지는 것을 시사하였다.축과 높은 정밀도 및 정확도로 반복적인 유기탄소분석에 유용할 것으로 사료된다./TEX>개월의 편차를 보였다. 이처럼 연령을 모르는 우리나라의 혼합치 열기 아동에서 파노라마 방사선 사진을 이용하여 연령 추정시 위의 방정식을 사용한다면 비교적 정확하게 연령을 추정할 수 있으리라고 사료된다. 상아질 접착제의 종류는 별다른 영향을 주지 않은 것으로 분석되었다. 결합강도의 비교에서 컴포머가 글라스 아이어노머에 비해 우수한 것으로 평가되어 소아 환자의 유구치 심미 수복재료로서의 가능성이 입증되었다.후 중합한 군이 산소억제층의 두께가 평균 49%의 감소되었으며(p<0.05), 이들 산소를 차단한 군 간의 유의차는 없었다.며 CYP1A2유전자형에 따른 영향은 관찰할 수 없었다. CYP1A2유전자형에 따른 생체내 대사능을 관찰하는 실험이 향후 이루어 져야 할 것으로 사료된다.san film보다 큰 수증기 투과도를 보였다.적으로 유의한 차이를 보이지 않았다.y tissue layer thinning은 3 군모두에서 관찰되었고 항암 3 일군이 가장 심하게 나타났다. 이상의 실험결과를 보면 술전 항암제투여가 초기에 시행한 경우에는 조직의 치유에 초기 5 일정도까지는 영향을 미치나 7 일이 지나면 정상범주로 회복함을 알수 있었고 실험결과 항암제 투여후 3 일째 피판 형성한 군에서 피판치유가 늦어진 것으로 관찰되어 인체에서 항암 투여후 수술시기는 인체면역계가 회복하는 시기를 3주이상 경과후 적어도 4주째 수술시기를 정하는 것이 유리하리라 생각되었다.한 복합레진은 개발의 초기단계이며, 물성의 증가를 위한 연구가 필요할 것으로 사료된다.또 다른 약물인 glycyrrhetinic acid($100{\mu}M$)도 CCh 자극으로 인한 타액분비를 억제하였다. 이상의 결과로

• 한국산림과학회지
• /
• 제21권1호
• /
• pp.1-34
• /
• 1974

1970~1971년(年)에 걸쳐 잣나무의 자웅화(雌雄花)가 개화(開花)하여 구과(毬果)가 성숙(成熟)하기까지 임업시험장(林業試驗場) 서울시험임내(試驗林內)에 고정모수(固定母樹) 2본(本)과 보조모수(補助母樹) 3본(本)을 선정(選定)하여 7~10일간격(日間隔)으로 구과(毬果)를 채취(採取)하여 외부형태(外部形態)와 내부조직(內部組織)의 변화상(變化相)을 밝히고 구과(毬果)의 종자(種子)의 함수량(含水量)을 비롯하여 유지(油脂), 당(糖), 단백질(蛋白質) 등(等) 함유물질(含有物質)의 변화(變化)와 발아력(發芽力)을 갖게되는 시기등(時期等)을 종합적(綜合的)으로 연구(硏究)하였으며 그 결과(結果)를 요약(要約)하면 다음과 같다. 1. 웅화(雄花) 1) 4월하순(月下旬)~5월상순(月上旬) 화분모세포군(花粉母細胞群)이 형성(形成)되고 다시 5월상순(月上旬)~5월중순(月中旬)에 환원분열(還元分裂)을 하여 사분자(四分子)가 되고 단핵상(單核狀)의 화분(花粉)은 그후분열(後分裂)하여 5월하순(月下旬) 성숙비산(成熟飛散)하였다. 2) 한 개의 웅화수(雄花穗)의 웅예수(雄蘂數)는 구과(毬果)의 유효인편수(有效鱗片數)와 거의 비슷한 69~102개(個)로서 1개(個)의 웅예내(雄蘂內)에는 5800~7300립(粒)의 화분(花粉)이 들어있다. 3) 성숙화분(成熟花粉)의 형태(形態)는 원형(圓形) 또는 타원형(楕圓形)으로 좌우(左右)에 기낭(氣囊)이 달렸으며 화분(花粉)의 길이는 $80{\sim}91{\mu}$로서 cuticula로 된 외피(外皮)와 cellulose로 된 엷은 내피(內皮)로 둘러 쌓여있다. 4) 성숙화분(成熟花粉)은 pH6.0의 증류수(蒸溜水)에 2%의 자당(蔗糖)을 넣은 0.8% 한천배지(寒天培地)를 사용(使用)하여 $25^{\circ}C$에서 68시간(時間) 경과후(經過後)에 발아(發芽)하였다. 2. 자화(雌花) 1) 인편(鱗片)은 4월하순(月下旬)부터 빨리 자라기 시작(始作)하여 5월상순(月上旬)에 배주(胚珠)의 분화(分化)가 시작(始作)된다. 5월중순(月中旬)에 배낭모세포(培囊母細胞)가 환원분열(還元分裂)을 하여 사분자(四分子)를 만들고 웅화(雄花)의 개화(開花) 직전(直前)인 5월하순(月下旬)~6월상순(月上旬)에 자화(雌花)의 생식기관(生殖器官)이 완성(完成)되었다. 2) 수분후(授粉後) 자화(雌花)의 배낭모세포핵(培囊母細胞核)은 계속(繼續) 분열(分裂)하여 다수(多數)의 유리핵(遊離核)이 밀집상태(密集狀態)로 익춘(翌春)까지 월동(越冬)한다. 3월중순(月中旬)부터 핵분열(核分裂)과 더불어 격막(膈膜)이 형성(形成)되어 5월상순(月上旬) 봉와조직상(蜂窩組織狀)의 배유체(胚乳體)가 형성(形成)되었다. 3. 수정(受精) 및 배(胚)의 형성(形成) 1) 장란기(藏卵器)는 4월중순(月中旬)~하순(下旬)에 형성(形成)되고 4월하순(月下旬)~5월초순(初旬) 사이에 수정(受精)하였다. 2) 배(胚)의 형성(形成)은 수정후(受精後) 5월하순(月下旬)에 난핵(卵核)이 분열(分裂)하여 일차(一次) suspensor 층(層)을 이루고 6월초순(月初旬)에 격막(膈膜)이 발생(發生)하였으며 6월중순(月中旬)에 4개(四個)의 유배(幼胚)가 발생(發生)하나 그중 1개(個)가 신장(伸長)하여 6월하순(月下旬)에는 배(胚)의 기관(器官)이 분화(分化)하기 시작(始作)하였으며 8월하순(月下旬)~9월초순(月初旬)에 배(胚)가 성숙(成熟)하였다. 4. 구과(毬果)의 생장(生長) 1) 개화당년(開花當年)의 6월중순(月中旬)~7월중순(月中旬)에 걸쳐 유구과(幼毬果)가 크게 생장(生長)하고 8월중순이후(月中旬以後) 정지(停止)되였는데 개화시(開花時)의 자화(雌花)에 비(比)하여 길이 1.6배(倍) 폭 3.3배(倍) 중량(重量)이 약(約) 22배(倍)에 달(達)하였다. 2) 개화익년(開花翌年)에는 3월상순(月上旬)부터 생장(生長)이 시작(始作)되어 4월중순(月中旬)~7월상순(月上旬)에 걸쳐 크게 생장(生長)하였으며 성숙기(成熟期)의 구과(毬果)는 개화직후(開花直後)의 유구과(幼毬果)에 비(比)하면 길이 7배(倍) 폭 12~15배(倍)에 달(達)하였다. 3) 구과중(毬果重)은 장란기(藏卵器) 형성기(形成期)에 65% 증가(增加)되고 수정후(受精後)에는 점진적(漸進的)으로 증가(增加)되어 7월하순(月下旬)에는 자화중(雌花重)의 660배(倍)로서 정점(頂點)을 이루고 그 후점차(後漸次) 감소(減少)되었다. 4) 구과(毬果)는 96~133개(個)의 인편(鱗片)으로 되어있고 종자(種子)가든 유효인편율(有效鱗片率)은 69~80%이며 성숙기(成熟期)의 구과장(毬果長)이 11~13cm 구과내종자수(毬果內種子數)는 90~150립(粒)이며 비립율(粃粒率)은 8~15%이었다. 5. 종피(種皮)의 형성(形成) 1) 자화(雌花)의 주피층분화(珠皮層分化)는 5월중순(月中旬)부터 시작(始作)되고 개화익춘(開花翌春)부터 활발(活潑)히 이루어져 외종피층(外種皮層)은 7월중순(月中旬)의 $703{\mu}$을 정점(頂點)으로하여 그후(後) 함수율(含水率)의 감소(減少)와 각질화(角質化)에 의(依)해 성숙기(成熟期)에는 $550{\sim}580{\mu}$로 감소(減少)되고 이때 외종피(外種皮)의 표피조직(表皮組織)이 분화(分化)하였다. 2) 성숙종자(成熟種子)의 외종피구조(外種皮構造)는 3~4층(層)의 표피세포층(表皮細胞層)과 16~21층(層)의 석세포(石細胞)로 되어 있고 그 내측(內側)에 1~2열(列)의 유조직층(柔組織層)을 이루고 있다. 3) 내종피(內種皮)는 외종피(外種皮)보다는 50~60일(日) 빠른 5월중순경(月中旬頃)에 최대층폭(最大層幅)($667{\mu}$)을 이루고 성숙종자(成熟種子)의 경우(境遇) 그 폭(幅)이 $80{\sim}90{\mu}$으로 감소(減少)되었다. 6. 함수율(含水率)의 변화(變化) 1) 수정후점차(受精後漸次) 증가(增加)되어 6월상순(月上旬)~중순경(中旬頃) 정점(頂點)에 달(達)하고 그후(後) 점감(漸減)되어 성숙기(成熟期)에는 구과(毬果) 43~48% 외종피(外種皮) 23~25% 내종피(內種皮) 32~37% 내종피(內種皮)와 배유(胚乳) 및 배(胚)는 23~26%배(胚)와 배유(胚乳)는 21~24% 배(胚)는 36~40%이었다. 2) 구과(毬果)의 발육(發育)과 함수율(含水率)의 증감관계(增減關係)를 종합(綜合)하면 다음과 같다. 제1기(第一期)(구과생장왕성기(毬果生長旺盛期) 수정후(受精後) 구과(毬果)의 발육왕성기(發育旺盛期))로서 최대함수량(最大含水量)을 나타내는 시기(時期)(4월하순(月下旬)--6월중순(月中旬)). 제2기(第二期)(배(胚) 및 영양조직형성기(營養組織形成期)) 유배(幼胚)가 발생(發生)되고 배유(胚乳)의 영양조직(營養組織)이 형성(形成)되며 함수율(含水率)이 점진적(漸進的)으로 고정(固定)되는 시기(時期)(6월중순(月中旬)~7월중순(月中旬)). 제3기(第三期)(성숙기(成熟期)) 내종피층폭(內種皮層幅)의 감소(減少)와 배(胚)의 성숙(成熟)으로 함수율(含水率)이 점차(漸次) 감소(減少)되고 실편(實片)이 황록색(黃綠色)으로 변색(變色)되는 시기(時期)(7월하순(月下旬)~8월하순(月下旬)). 제4기(第四期)(건조기(乾燥期)) 종자(種子)가 성숙(成熟)하여 함수율(含水率)이 급감(急減)되고 실편(實片)이 건조(乾燥) 위축(萎縮)하는 시기(時期)(9월초순이후(9月初旬以後)). 7. 함유물질(含有物質)의 변화(變化) 1) 종자내(種子內)의 유지(油脂)는 수정후(受精後) suspensor 층(層)이 형성(形成)되는 5월상순(月上旬)부터 점차(漸次) 증가(增加)되고 배(胚)의 기관(器官)이 분화(分化)되는 시기(時期)부터 급감(急減)되어 성숙종자(成熟種子)의 함유율(含油率)이 65~68%로서 호도와 참깨 야자수 열매등(等) 유지작물(油脂作物)보다 많았으며 배유(胚乳)보다 배(胚)의 함유율(含油率)이 높았다. 2) 수정후구과(受精後毬果)의 생장(生長) 왕성기(旺盛期)에 환원당(還元糖)의 함량(含量)이 일시증가(一時增加)하였으나 6월상순(月上旬)부터 점감(漸減)되고 비환원당(非還元糖)이 증가(增加)하였다. 배(胚)의 전당함량(全糖含量)은 7월하순(月下旬)부터 점차적(漸次的)으로 증가(增加)하였는데 그 대부분(大部分)이 비환원당(非還元糖)이였으며 환원당(還元糖)은 비환원당(非還元糖)의 약(約) 1/10에 불과(不過)하였다. 3) 단백질(蛋白質)의 함량(含量)은 5월하순(月下旬)부터 점차(漸次) 증가(增加)하였으며 성숙종자(成熟種子)의 경우(境遇) 48.8%였으며 배(胚)보다 배유(胚乳)쪽이 많았다. 8. 종자(種子)의 형질(形質) 성숙(成熟)한 종자(種子)는 외관상(外觀上) 다갈색(茶褐色)이고 길이는 1.3~1.9cm 폭(幅) 0.8~1.4cm 중량(重量) 0.43~0.48g이였으며 외종피(外種皮)는 종자중량(種子重量)의 61~65% 배(胚)는 2.3~3.5% 내종피(內種皮)와 배(胚) 및 배유(胚乳)는 33~36%이였다. 9. 발아력(發芽力)의 검정(檢定) 7월하순(月下旬)부터 9월중순(月中旬)까지 7일간격(日間隔)으로 채종(採種)하여 환원법(還元法)과 배적출(胚摘出) 배양(培養) 및 일반발아시험등(一般發芽試驗等) 세가지 방법(方法)으로 발아력(發芽力)을 검토(檢討)한 결과(結果) 수정(受精) 4개월후(個月後)인 8월하순(月下旬)부터 정상적(正常的)인 발아력(發芽力)을 갖게 되었고 이때 종자(種子)의 함수량(含水量)이 22~25%이었다. 이로 미루어 잣나무의 채종적기(採種適期)는 9월상순(月上旬)이라고 볼 수 있다.

• 한국토양비료학회지
• /
• 제5권2호
• /
• pp.1-38
• /
• 1972

우리나라 답토양(畓土壤)에 대(對)한 토지(土地)의 합리적(合理的) 이용(利用), 토지기반조성(土地基盤造成) 및 생산성 향상(向上) 그리고 토양(土壤)에 관(關)한 조사연구(調査硏究)의 방향(方向)을 뒷받침하기 위(爲)하여 김제만경평야(金堤萬頃平野)에 분포(分布)하고 있는 답토양(畓土壤)에 대(對)한 형태(形態) 및 이화학적(理化學的) 특성(特性) 그리고 그와 수도수량(水稻收量)과의 관계(關係)를 구명(究明)하고 이를 기초(基礎)로 하여 답토양(沓土壤)의 분류법(分類法)과 적성등급구분(適性等級區分)을 시안(試案)하였는 바 그 결과(結果)를 요약(要約)하면 다음과 같다. 1. 답토양(畓土壤)의 형태(形態), 이화학적(理化學的) 특성(特性) 및 그와 수도수량(水稻收量)과의 관계(關係) 김제(金堤) 만경평야(萬頃平野)에 분포(分布)하고 있는 15개(個) 답토양통(畓土壤統)에 대(對)하여 이들 토양(土壤)의 형태(形態), 이화학적(理化學的) 특성(特性)을 보면 다음과 같다. 토양단면(土壤斷面)의 발달정도(發達程度)를 보면 공덕(孔德), 김제(金堤), 만경(萬頃), 백구(白鷗), 봉남(鳳南), 부용(芙蓉), 수암(水岩), 전북(全北), 지산(芝山) 및 호남통(湖南統)는 B(Cambic B)층(層)이 있고 극락(極樂)과 화동통(華東統)은 Bt(Argillic B)층(層)이 있으나 광활(廣活), 신답(新踏) 및 화계통(華溪統)에는 B층(層) 혹(或)은 Bt층(層)이 없다. 특(特)히 공덕(孔德) 및 봉남통(鳳南統)은 흑니층(黑尼層)이 심토(心土) 하부(下部)에 개재(介在)되여 있다. 토양단면(土壤斷面)의 토색(土色)을 보면 공덕(孔德), 광활(廣活), 백구(白鷗) 및 신답통(新踏統)은 대체(大體)로 청회색(靑灰色), 암회색(暗灰色)을 띄우고 김제(金堤), 만경(萬頃), 봉남(鳳南), 부용(芙蓉), 수암(水岩), 전북(全北), 지산(芝山) 및 호남통(湖南統)은 회색(灰色), 회갈색(灰褐色)을 띠우며 극락(極樂), 화계(華溪) 및 화동통(華東統)은 표토(表土) 및 표토하부(表土下部)의 회색(灰色)을 제외(除外)하고 황갈색(黃褐色), 갈색(褐色)을 띠운다. 토양단면(土壤斷面)의 토성(土性)을 보면 공덕(孔德), 극락(極樂), 김제(金堤), 봉남부용(鳳南芙蓉), 호남(湖南) 및 화동통(華東統)은 식질(埴質)이고 백구(白鷗), 전북(全北) 및 지산통(芝山統)은 식양질(埴壤質) 혹은 미사식양질(微砂埴壤質)이며 광활(廣活), 만경(萬頃) 및 수암통(水岩統)은 미사사양질(微砂砂壤質) 그리고 신답(新踏) 및 화계통(華溪統)은 사질(砂質) 혹은 석력사질(石礫砂質)이다. 표토(表土)의 탄소함량(炭素含量)은 0.29%~2.18% 범위(範圍)에 있으나 1.0~2.0%인 것이 많으며 표토(表土)의 전질소함량(全窒素含量)은 0.03%~0.24% 범위(範圍)에 있다. 이들은 심토(心土) 혹은 기층(基層)으로 갈수록 감소(減少)되는 경향(傾向)이나 불규칙적(不規則的)이다. 표토(表土)의 탄질비(炭窒比)는 4.6~15.5 범위(範圍)인데 8~10인 것이 많으며 심토(心土) 및 기층(基層)에서는 표토(表土)에 비(比)하여 그 범위(範圍)가 커서 3.0~20.25이다. 토양반응(土壤反應)은 pH4.5~8.0 범위(範圍)에 있으나 광활(廣活) 및 만경통(萬頃統)을 제외(除外)하고는 모두 산성(酸性)이다. 염기치환용량(鹽基置換容量)은 표토(表土)에서는 5~13 me/100g 범위(範圍)이며 심토(心土) 및 기층(基層)에서는 사질토양(砂質土壤)을 제외(除外)하고 모두 10~20 me/100g 범위(範圍)에 있다. 염기포화도(鹽基飽和度)는 공덕(孔德) 및 백구통(白鷗統)을 제외(除外)하고는 모두 60% 이상(以上)이다. 표토(表土)의 활성철함량(活性鐵含量)은 0.45~1.81% 범위(範圍)이고 역환원성(易還元性)망간은 15~148ppm 범위(範圍)이며 유효규산은 36~366ppm 범위(範圍)에 있다. 이들 3성분(成分)의 용탈(溶脫) 및 집적(集積)은 토양배수(土壤排水), 토성조건(土性條件)에 따라 다르지만 대체(大體)로 10~70cm 범위(範圍)에 집적(集積)하고 있으나 규산(珪酸)은 경우(境遇)에 따라 철(鐵), 망간 보다 깊은 층위(層位)에 집적(集積)되여 있다. 각(各) 토양통(土壤統)의 주요특성(主要特性)은 해안(海岸)에서 부터 거리에 따라 점변(漸變)하고 있으며 점토(粘土), 유기탄소(有機炭素) 및 pH는 해안(海岸)으로 부터 내륙(內陸)으로 옮겨가는 거리와 다음과 같은 상관(相關)이 있다. y(표상(表上)의 점토함량(粘土含量)) = $$-0.2491x^2+6.0388x-1.1251$$ y (심토(心土) 및 표토하부(表土下部)의 점토함량(粘土含量)) = $$-0.31646x^+7.84818x-2.50008$$ y(표토(表土)의 유기탄소함량(有機炭素含量)) = $$-0.0089x^2+0.2192x+0.1366$$ 로서 내륙(內陸)으로 갈수록 높아지는 경향(傾向)이며 y(심토(心土) 및 표토하부(表土下部)의 pH) = $$0.0178x^2-0.4534x-8.353$$ 로서 내륙(內陸)으로 갈수록 낮다. 토양(土壤)의 형태(形態) 및 이화학적(理化學的) 특성(特性)에 있어 특기(特記)되는 것은 토양(土壤)의 발달도(發達度), 토색(土色), 모재(母材)의 다원적(多元的) 퇴적(堆積), 유기물층(有機物層)의 개입(介入), 토성(土性) 및 토양반응(土壤反應) 등(等)이였으며 이들은 답토양(畓土壤)의 분류(分類)에서 고려(考濾)되여야 할 사항(事項)이였다. 토양(土壤)의 몇가지 특성(特性)과 수도수량(水稻收量)과의 관계(關係)에서 토양배수(土壤排水)가 약간양호(若干良好) 내지(乃至) 불량(不良)한 식질토(埴質土), 양질토(壤質土) 그리고 유효심도가 낮은(50cm) 식질토(埴質土)들은 수량(收量)이 대부분(大部分) 10a당(當) 375kg 이상(以上)이며 사질토(砂質土), 배수(排水)가 양호(良好)한 식질토(埴質土), 유효심도가 낮은 양질토(壤質土) 및 함염토(含鹽土)들은 수량(收量)이 대부분(大部分) 10a당(當) 375kg미만(未滿)이다. 수도수량(水稻收量)에 영향(影響)을 미치는 토양(土壤)의 형태적(形態的) 특성(特性)은 토양배수(土壤排水), 토성(土性), 유효심도, 표토(表土) 및 표토하부(表土下部)의 회색화(灰色化) 그리고 염농도(鹽濃度) 등(等)이며 이들은 답토양(畓土壤)의 적성등급구분(適性等級區分)에서 고려(考慮)되여야 할 사항(事項)이였다. 2. 답토양(畓土壤)의 분류(分類) 및 적성등급구분(適性等級區分) 답토양(畓土壤)의 분류기준(分類基準)은 토양(土壤) 자체(自體)가 가지고 있는 성질(性質)에 근거(根據)를 두었다. 토양분류단위(土壤分類單位)는 토양대군(土壤大群), 토양군(土壤群), 토양아군(土壤亞群), 토양계(土壤系) 그리고 토양통(土壤統)의 5단계(段階)를 두고 분류(分類)의 기본(基本) 단위(單位)는 토양통(土壤統)으로 하였다. 토양분류(土壤分類)에 있어 형태적(形態的) 특성(特性)의 차이(差異)를 결정(決定)하기 위(爲)하여 2종류(種類)의 특징토층(特徵土層) 즉(卽) 숙성토층(熟成土層) 및 반숙토층(半熟土層)을 설정(設定)하여 이들의 유무(有無) 및 종류(種類)를 토양대군(土壤大群)의 분류기준(分類基準)으로 하였다. 토양군(土壤群) 및 토양아군(土壤亞群)의 분류(分類)에 있어 고려(考慮)되여야 할 특징적(特徵的) 토양특성(土壤特性)은 우선(于先), 토색(土色), 염농도(鹽濃度), 표토(表土) 및 표토(表土) 하부(下部)의 회색화(灰色化), 토사(土砂)의 다원적(多元的) 퇴적(堆積) 그리고 유기물층(有機物層)의 개입(介入)으로 하였으며 토양계(土壤系)의 분류(分類)에서 고려(考慮)한 토양특성(土壤特性)은 토양반응(土壤反應), 토성(土性) 및 석력함량(石礫含量)에 근거(根據)를 두어 분류(分類)하는 한편 이들에 대(對)한 정의(定義)를 내렸다. 그리고 필자(筆者)의 시안(試案)과 기존(旣存)의 분류안(分類案)을 상호비교(相互比較)하여 검토(檢討)하였다. 답토양(畓土壤)의 적성등급구분(適性等級區分)은 인위적(人爲的) 작용(作用)에 의(依)한 가변성(可變性)이 적은 토양특성(土壤特性)을 토대(土臺)로 하였으며 등급구분단위(等級區分單位)는 등급(等級) 및 아급(亞級)의 2단계(段階)를 두었다. 등급(等級)은 토양(土壤)의 잠재생산력(潛在生産力)이 어느 주어진 단위(範圍)에서 같고 토지이용(土地利用) 및 관리(管理)의 난이(難易)를 고려(考慮)한 토양조건(土壤條件)에 따라 1급(級)에서 4 급지(級地)까지의 4 등급(等級)으로 구분(區分)하였고 아급(亞級)은 동일등급내(同一等級內)에서 중요(重要)한 제한인자(制限因子)로 하였으며 그 인자(因子)는 경사(傾斜), 저염(低濕), 사질(砂質) 석력(石礫), 염해(鹽害), 미력(美熟)이다. 이들 등급(等級) 및 아급(亞級)을 각각(各各) 정의(定義)를 하였으며 아울러 분류시안(分類試案)과의 연관성(連關性)을 검토(檢討)하였다. 김제(金堤) 만경평야(萬頃平野)의 15개(個) 답토양통(畓土壤統)의 분류(分類) 및 적성등급(適性等級) 구분시안(區分試案)을 종합(綜合)하여 보면 다음과 같다.

• Radiation Oncology Journal
• /
• 제25권4호
• /
• pp.242-248
• /
• 2007

목적: 마우스 모델에서 cisplatin과 방사선조사로 구내염을 유발시킨 후 재조합 표피성장인자 (recombinant human epidermal growth factor, rhEGF)을 처치하여 그 효과를 알아보고자 하였다. 대상 및 방법: 마우스 24마리를 대상으로 정상대조군 8마리와 실험군은 각각 rhEGF 처치군과 미처치군으로 8마리씩 분류하였으며 실험군은 10 mg/kg의 cisplatin을 방사선조사 첫날 동시에 1회 복강 내 투여하였고, 방사선조사는 5일간 1회 5 Gy씩, 5일간 25 Gy를 조사하였다. RhEGF 처치군은 방사선조사 2일 전부터 2일간 1 mg/kg의 rhEGF를 피하주사하였으며 방사선조사3일째부터 3일간 1 mg/kg를 피하주사하여 총 5 mg/kg의 rhEGF를 투여하였다. 마우스의 체중변화, 먹이섭취 및 조직학적 변화를 평가하였다. 결 과: 마우스 체중변화는 rhEG F처치군이 실험 3일째부터 5일간 rhEGF 미처치군과 비교하여 통계적으로 유의한 체중의 차이를 관찰할 수 있었다. 먹이섭취는 실험군(rhEGF 처치군과 미처치군)에서 실험 5일째까지 감소하였다가 13일째부터 먹이섭취의 증가를 보여주었다. Cisplatin과 방사선조사 후 7일째의 조직학적 검사에서는 rhEGF 처치군에서 마우스의 점막 표피층의 변성이 관찰되었으나 rhEGF 미처치군에서는 점막층의 염증 반응이 관찰되었다. 결 론: Cisplatin과 방사선 조사로 마우스에서 발생한 구내염에서 rhEGF를 투여한 경우 체중 변화와 먹이섭취의 유의한 개선을 관찰하였으며 조직학적 검사에서 점막 손상의 회복을 확인하였다. 향후 임상적으로 rhEGF가 항암화학요법과 방사선치료로 인한 구내염을 줄일 수 있는 가능성을 확인하였다.값은 11개월이었고 2년, 3년 생존율은 31.5%, 15.8%였다. 결 론: 2기 췌장암 환자들은 국소 재발 및 원격 전이의 가능성이 높은 고위험군으로 국소 제어율 및 전체 생존율의 향상을 위해서 수술 후 효과적인 방사선치료의 적극적인 시행 및 이후의 보조적인 전신 항암화학요법을 권고하여 시행하는 것이 바람직하다. 평가 검사는 모두 제조사의 시험지침서에 부합하였다. 결론적으로, 이는 본 GE $Advance^{TM}$ PET 시스템이 임상에의 적용에 적합함을 보여주었다.mens사의 상용 분석 프로그램에는 해당 기능이 없어 계산값의 비교를 통한 검증은 수행하지 못하였고, 수화(hydration)와 탈수(dehydration) 각각의 조건에 따른 신장기능 분석에 적용하였을 때, 판별 기준이 되는 유의미한 값을 산출하여 타당성 검증을 대신하였다. 결론: 이 연구에서 개발한 핵의학 영상의 정량적 분석을 통한 신장기능 분석 프로그램을 사용하여 신장 기능을 분석한 결과, 타당성 있는 결과를 도출하여 그 유용성을 입증하였다. 이 개발 프로그램은 좀 더 다양한 임상응용 목적의 분석기능을 사용자가 직접 개발, 추가하기가 용이하여 기존 상용 프로그램보다 연구적 활용범위가 크다고 사료된다.2.2{\pm}0.4\;(1.6{\sim}3.2){\mu}g/ml$와 $1.4{\pm}0.2\;(0.8{\sim}1.6){\mu}g/ml$로서(p=0.16), 표준균주 3종 모두에서 Infecton의 MBC 또한 ciprofloxacin에 비해 $2{\sim}4$배가 높았다. 결론: Tc-99m Infecton은 ciprofloxacin 보다는 약하였지만 표준균주에 대해 생체외 항균력을 보였다.를

• 한국작물학회지
• /
• 제11권
• /
• pp.81-97
• /
• 1972

논벼농사의 노동력을 덜기 위하여 이중 가장 중요한 호미질에 의한 중경제초의 노력을 살초제에 의한 것으로 전환시키고자 기초적인 면과 실제적인 면으로 시험조사를 하였다. 건국대학교에서 1m평방 안높이 21cm 및 36cm의 두 형의 concrete tank를 각 4개씩 만들고 그 안에 채수관장치를 한 뒤 양토작토로 논벼를 심어 수도물로 관수하고 투수속도와 산소침투 정도와 수량과의 관계를 보았다. 농림부 자재 검사소 내에서 투수가 심한 사질답전포장에 전면적으로 살초제 Stam F-34를 살포하여 제초하고 제 1구는 중경을 하지 않고, 제 2구는 중경 1회, 그리고 제 3구는 중경 2회하여 중경의 효과를 비교하였다. 이리 호남시험장내 건답보통논과 습답에 무중경, 중경 1회 중경 2회의 구와 살초제 Pamcon을 살포한 것들 중, 무중경, 중경 1회 제초 2회, 중경 2회 제초 1회, 중경 3회 제초 2회의 구와 그리고 관행구를 설치하여 중경제초의 비용과 살초제에 의한 비용을 비교하였던바 그 결과를 요약하면 다음과 같다. (1) 투수속도와 산소침투와 수량과의 관계는 일당(24시간당) 투수속도 4cm이상 될 때 지표 2cm하에 산소가 조금 들어가며 3cm보다 적을 때는 산소가 지표하의 매우 옅은 층에만 내려가는 것으로 나타나며 그리고 경심 15cm구에는 일당 투수속도의 0cm(무투수) 1.5cm에서 수량이 많고 2.5cm와 3.4cm에는 감수되며, 경심 30cm구에는 투수속도 1.5cm 및 30cm구에서 수량이 많고 무투수와 투수속도 4cm구에는 수량이 떨어졌다. (2) 투수가 심한 농림부 자재검사소 사질토양에서는 중경의 효과가 없었다. (3) 호남작물시험장내 건답에서는 살초제 Pamcon 처리 무중경구 수량에 대해서 유의성이 보이는 증수구는 없었다. 그리고 습답에서는 무중경구에 있어서 중경제초 및 관행구가 유의성 있게 증수되었다. (4) 논매기 호미질에 의한 10a당 노동력은 정미 37.1시간 식사와 휴식시간 포함하여 53.5시간이고, 노임은 2,346원인데 대하여 살초제 사용에의 한제 초노력은 수동식으로 0.5일 즉 약 5시간 제비용과 감수추정량을 추정할 때 1,130원이고 습답을 제외하면 750원이 되는 것으로 추정 되었다.

• 한국토양비료학회지
• /
• 제11권2호
• /
• pp.97-104
• /
• 1979

토양정밀조사결과 우리나라에서 밝혀진 235 개(個)의 토양통에 대하여 분류체계를 확립(確立)코저 미국(美國)의 신토양분류법에 준(準)하였는바 60개(個)의 아군으로 구분할 수 있었다. 그러나 수도재배기간중(水稻栽培期間中) 담수상태(湛水狀態)를 유지(維持)하게되는 답토양들은 신분류법(新分類法)에 분류기준(分類基準)이 확립(確立)되어 있지않아 토양형태적특성에 입각(立脚)하여 분류(分類)코저 할때 무리(無理)가 있음을 알 수 있었다. 답토양의 분류상(分類上) 문제시(問題視)된 것은 토양아군의 수준(水準)에서 18개(個)였으며 이들 새로운 아군에 대하여 분류기준(分類基準)을 설정(設定)(Setup)하였는 바 그 분류시안(分類試案)의 내용(內容)을 요약(要略)하면 다음과 같다. Anthro aquic, Aquic Udipsamments; 관개수(灌漑水)의 영향(影響)을 받아 표토(表土)로 부터 50cm이상(以上) 회색화작용(灰色化作用)을 받은 사질계충적토(砂窒系沖積土)이며 사두(沙頭)및 김천통등(金川統等)이 이에 속(屬)한다. Anthroaquic Udipsamments; 관개수(灌漑水)의 영향(影響)을 받아 표토(表土)로 부터 50cm 이내(以內)에서 회색화작용(灰色化作用)을 받은 사질계충적토(砂窒系沖積土)로 백수통(白岫統)이 이에 속(屬)한다. Halic Psammaquents; 개답년대(開畓年代)가 오래되지 않은 간척지의 염해답으로 낙천통이 이에 속(屬)한다. Anthroaquic, Aquic Udifluvents; 관개수(灌漑水)의 영향(影響)을 받아 표토(表土)에서 50cm이상(以上) 회색화작용(灰色化作用)을 받은 사양질 및 식양질계 충적토로 마영통(馬嶺統)이 이에 속(屬)한다. Anthroaquic Udifluvents: 관개수(灌漑水)의 영향(影響)을 받아 표토(表土)로부터 50cm이내(以內)에서 회색화작용(灰色化作用)을 받은 사양질 및 식양질계 충적토로 행곡통(杏谷統)이 이에 속(屬)한다. Fluventic Haplaquepts: 지하수위(地下水位)가 높아 토양은 전층이 회색화(灰色化)된 습답으로 유기물(有機物)의 함량(含量)은 토심(土深)이 깊어짐에 따라 불규칙적(不規則的)으로 감소(減少)되는 회색토(灰色土)로 백구 및 학성통등(鶴城統等)이 이에 속(屬)한다. Fuventic Thapto-Histic Haplaquepts: Fluventic Haplaquepts와 유사(類似)하나 토양단면내에 유기물층이 개재된 습답으로 공덕(孔德) 및 서탄통(西炭統)이 이에 속(屬)한다. Fluventlc Aeric Haplaquepts: Fluventic Haplaquepts보다 지하수위(地下水位)가 비교적(比較的) 낮으므로 토양배수가 약간 불량(不良)한 회색토(灰色土)로 만경(萬頃) 및 전북통등(全北統等)이 이에 속(屬)한다. Fluventic Thapto-Histic Aeric Hapldquepts: Fluventic Thapto-Histic Haplaquepts보다 지하수위(地下水位)가 비교적(比較的) 낮으므로 토양배수가 약간 불량(不良)한 회색토(灰色土)로 봉남통(鳳南統)이 이에 속(屬)한다. Fluventic Aeric Sulfic Haplaquepts: Fluventic Aeric Haplaquepts에 비(比)하여 토심(土深) 50~150cm 사이에 황색반문(黃色斑紋)(PH<4.0)인 유화물집적층이 있는 회색토(灰色土)로 등구통이 이에 속(屬)한다. Fluventic Sulfaquepts: 이들 토양은 주(主)로 강하류(江下流)에서 바다로 유입(流入)되는 지점(地点) 및 간석 소택지에 분포(分布)되며 표토(表土)에서 50cm이내(以內)에 유화물집적층이 있는 습답으로 봉림(鳳林) 및 해척통(海拓統)이 이에 속(屬)한다. Fluventic Aeric Sulfaquepts: Fluventic Sulfaquepts 보다 지하수위(地下水位)가 비교적(比較的) 깊으므로 토양 배수(排水)가 약간 불량(不良)한 회색토(灰色土)로 김해통(金海統)이 이에 속(屬)한다. Anthro aquic Fluvaquentic Eutrochrepts: 관개수(漑水)의 영향(影響)을 받아 표토(表土)로 부터 50cm이상(以上) 회색화(灰色化)되고 염기포화도가 높은(>60%) 토양이며 장유(長有) 및 칠곡통등(漆谷統等)이 이에 속(屬)한다. Anthro aquic Dystric Fluventic Eutrochrepts: Anthro aquic Fluvaquentic Eutrochrepts와 유사(類似)하나 회색화작용(灰色化作用)은 표토(表土)로부터 50cm이내(以內)에서만 나타나는 토양이며 월곡(月谷) 및 경산통등(慶山統等)이 이에 속(屬)한다. Anthro aquic Fluventic Dystrochrepts; Anthro aquic Dystric Fluventic Eutrochrepts에 비(比)하여 염기포화도가 낮은(<60%) 토양으로 고천(高川) 및 비곡통등(秘谷統等)이 이에 속(屬)한다. Anthre aquic Eutrandepts; 염기포화도가 높은 (>50%) 화산회토(火山灰土)로 대정통(大靜統)이 이에 속(屬)한다. Anthre aquic Hapludalfs; 관개수(灌漑水)의 영향(影響)을 받아 표토(表土)로부터 50cm 이내(以內)에서 회색화작용(灰色化作用)을 받은 적황색토(赤黃色土)로 화동(華東) 및 용수통등이 이에 속(屬)한다. Anthro aquic Aquic Hapludalfs; Anthro aquic Hapludalfs에 비(比)하여 회색화작용(灰色化作用)을 더 받은(표토(表土)에서 50cm이상(以上)) 적황색토(赤黃色土)로 덕평(德坪) 및 극락통등이 이에 속(屬)한다.

• 대한의용생체공학회:의공학회지
• /
• 제6권2호
• /
• pp.1-8
• /
• 1985

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70$\pm$1.32mmHg/min)compared to CF dialyzers(4.32$\pm$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500, 550, 570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500, 550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100, 300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3, 000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.SpO2 with Plethysmograph.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.