• Korean Journal of Materials Research
• /
• v.8 no.5
• /
• pp.408-412
• /
• 1998

Thermoelectric properties of Bi$_{2}$(Te$_{1-x}$Se$_{ x}$)$_{3}$(0.05$\leq$x$\leq$0.25) prepared by mechanical alloying and hot pressing, were investigated. Contrary to the p-type behavior of single crystals, the hot-pressed Bi$_{2}$(Te$_{1-x}$Se$_{ x}$)$_{3}$ exhibited ntype conduction without addition of donor dopant. When $Bi_2(Te_{0.85}Se_{0.15})_3$powders were annealed in (50% $H_2$ + 50% Ar) atmosphere, the hot-pressed specimen exhibited a positive Seebeck coefficient due to the reduction of the electron concentration by removal of the oxide layer on the powder surface and annealing-out of the excess Te vacancies. Among the Bi$_{2}$(Te$_{1-x}$Se$_{ x}$)$_{3}$fabricated by mechanical alloying and hot pressing, $Bi_2(Te_{0.85}Se_{0.15})_3$ exhibited a maximum figure-of-merit of 1.92 $\times$ $lO^{-3}$/K.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.169-169
• /
• 2008

To keep pace with scaling trends of CMOS technologies, high-k metal oxides are to be introduced. Due to their high permittivity, high-k materials can achieve the required capacitance with stacks of higher physical thickness to reduce the leakage current through the scaled gate oxide, which make it become much more promising materials to instead of $SiO_2$. As further studying on high-k, an understanding of the relation between the etch characteristics of high-k dielectric materials and plasma properties is required for the low damaged removal process to match standard processing procedure. There are some reports on the dry etching of different high-k materials in ICP and ECR plasma with various plasma parameters, such as different gas combinations ($Cl_2$, $Cl_2/BCl_3$, $Cl_2$/Ar, $SF_6$/Ar, and $CH_4/H_2$/Ar etc). Understanding of the complex behavior of particles at surfaces requires detailed knowledge of both macroscopic and microscopic processes that take place; also certain processes depend critically on temperature and gas pressure. The choice of $BCl_3$ as the chemically active gas results from the fact that it is widely used for the etching o the materials covered by the native oxides due to the effective extraction of oxygen in the form of $BCl_xO_y$ compounds. In this study, the surface reactions and the etch rate of $Al_2O_3$ films in $BCl_3/Cl_2$/Ar plasma were investigated in an inductively coupled plasma(ICP) reactor in terms of the gas mixing ratio, RF power, DC bias and chamber pressure. The variations of relative volume densities for the particles were measured with optical emission spectroscopy (OES). The surface imagination was measured by AFM and SEM. The chemical states of film was investigated using X-ray photoelectron spectroscopy (XPS), which confirmed the existence of nonvolatile etch byproducts.

• Resources Recycling
• /
• v.16 no.6
• /
• pp.3-9
• /
• 2007

Although the ferrous material was separated by the magnetic separation before the incineration process, the municipal solid waste incineration bottom ash generated during incinerator in metropolitan area consists of many iron products which account for about $3{\sim}11%$ as well as ceramics and glasses. The formation of $NiFe_2O_4$ and $FeCr_2O_4$ with a $Fe_3O_4-Fe_2O_3$ (similar to pure Fe) on the surface of iron product was found during air-annealing in the incinerator at $1000^{\circ}C$, because Ni and Cr has a chemical attraction about iron is using to coat with Ni and Cr metals for poish or to prevent corrosion. Therefore, Fe-Ni Cr oxide can be formed on durface of the iron product and it can be separated from bottom ash through the magnetic separation. So, in this study, the separation ratio of heavy metals as magnetic separation and mineralogical formation of Fe-ion(heavy metal) in ferrous metals corroded were investigated. As the result, the separation ratio of Ni and Cr based on particle sizes accounted for about $45{\sim}50%$, and Cu and Pb accounted for below 20%. Also, the leaching concentration of Ni and Cr in bottom ash separated by magnetic separation was lower than that in fresh bottom ash.

• Korean Chemical Engineering Research
• /
• v.43 no.2
• /
• pp.324-329
• /
• 2005

The efficiency of reducing nitric oxide using urea combined with alkali salt additives is reported in this study. The inlet concentration of NO is 500 ppm with air flow rates of 3 and 5 L/min. Reduction of NO was studied from 650 to $1,050^{\circ}C$ with urea concentrations of 0.3 to 1 mol/L. The efficiency for the reduction of NO increased by 44% when urea is added alone. A further increase in efficiency was observed in the presence of NaOH as additive in fact, the efficiency was increased by more than 25% and 75% when 0.5 mol/L and 1 mol/L NaOH were added with the urea. The efficiency for the reduction of NO increased with all additives, but descended in the order NaOH, $Na_2CO_3$, $NaNO_3$, HCOONa, and CHCOONa. The maximum efficiency of NaOH and $Na_2NO_3$ are 74% and 73%, respectively. All these additives did not alter the comparatively wide operating temperature window for reducing NO. However, sodium compounds do not shift the maximum NO concentration towards lower temperatures when the NO removal activity enhances.

• Journal of the Microelectronics and Packaging Society
• /
• v.16 no.3
• /
• pp.31-37
• /
• 2009

Cu-Cu thermo-compression bonding process was successfully developed as functions of the $N_2+H_2$ forming gas annealing conditions before and after bonding step in order to find the low temperature bonding conditions of 3-D integrated technology where the quantitative interfacial adhesion energy was measured by 4-point bending test. While the pre-annealing with $N_2+H_2$ gas below $200^{\circ}C$ is not effective to improve the interfacial adhesion energy at bonding temperature of $300^{\circ}C$, the interfacial adhesion energy increased over 3 times due to post-annealing over $250^{\circ}C$ after bonding at $300^{\circ}C$, which is ascribed to the effective removal of native surface oxide after post-annealing treatment.

• Resources Recycling
• /
• v.5 no.3
• /
• pp.65-72
• /
• 1996

Colloidal calcium wrbonate(diametcr 0.02-0 09 m~wja s developed to maintain the mamenl of pnriide formatio~>w ~lhoutsurlace trealment. The control factors of particle size and optimum condiliuna for compound fam*tition has not bccn studiedyet. This shldy war aimed at developing a method fur compounding colloidal calcium carbonfcte to cnl~hol cubic calciumcarbonate, and then compounding the b-o types oI precipitated calcium wrbonatc under optimum wndilrans Calc~umhydroxide was calcinated at 1, lWC far two hours, md then hydrated for 30 minutes at t i i O rprn and ambiznt temperahlle.Two-liter suspension was subjected to the contact with carbon dioxide at l5"C, 600 ipxn and C0= injection in the rate of 1 Umin Two types of dcium carbonate(cuhic calcium carbonatc(0 24.9 pm) md collnidd calcium mhnnate (0.02-0 09 pm))were compounded by "wing the concentrations of calcium oxide and ihe suspension were compounded. It was found that theoptimum concentrations of each suspensions were 5 wt % and 2.5 \I*.% respectively. ' h c key control factor af thc parlicle slzcdislribution was the concenkation al the suspension. The size of compounded particles was measured by a Zcla S k r 'fieaverage particle size of the cubic calcium carbonate aas 223.4 nm(0.223 pm), and that of thc colloidal a~lciumc arbonate was93.6 nm (0.093 km). Ihe particle sizc was evenly cantlolled on a stdblc basis in an H, O reaction system.asis in an H, O reaction system.

• Journal of Soil and Groundwater Environment
• /
• v.9 no.4
• /
• pp.52-61
• /
• 2004

In order to remediate soils contaminated with oxyanionic As and cationic Zn and Ni through the pilot-scale acid washing, the effectiveness of acid washing and the properties of contaminated soils, fine soil particle and dissolved contaminants were evaluated. $H_{2}SO_4\;and\;H_{3}PO_4$ washing at pH $2{\sim}3$ enhanced the removal of As by the presence of competitive oxyanions and HCl washing effectively removed simultaneously As, Zn and Ni. The effectiveness of soil washing was little enhanced above the critical reaction time, and the carbonate, Fe/Mn oxide and organic/sulfides associated fraction were dominantly removed. The washing of coarse soil particles was highly efficient, but that of fine soil particles($<74{\mu}m$) was recalcitrant due to the enrichment with contaminants. Moreover, the physical separation of fine particles($<149{\mu}m$) enhanced the overall efficiency of soil washing. Therefore, both chemical extraction and separation of fine soil particles showed the high effectiveness of soil washing in the intersection point to minimize the amount of fine soil particles and to maximize the chemical extraction of contaminants.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.26 no.4
• /
• pp.614-619
• /
• 1997

To examine effects of drying methods on the formation of N-nitrosamine(NA) in squid during its drying. Three different types of dried products, which were made by sun, hot-air and traditional drying of squid after removal of intestines, were utilized. NA was analyzed by a gas chromatography-thermal energy analyzer. The contents of nitrate and nitrite nitrogen in dried products were in the range of 0 to 5.2mg/kg and 0 to 2.7mg/kg, respectively. The contents of TMAO and betain nitrogen in squid during its drying decreased, while those of TMA and DMA nitrogen increased. The contents in dried products were 27.8~29.2mg% and 10.4~12.3mg/kg, respectively. N-Nitrosodimethylamine (NDMA) was only detected in squid during its drying, recovery from raw sample and its dried pro- ducts spiked with 10$\mu\textrm{g}$/kg for NDPA was 81.0~ 100.0%. NDMA in raw samples was found to be below 0.05$\mu\textrm{g}$/kg. The levels of NDMA in squid increased remarkably during its drying and those in dried products were ranged from 2.7 to 42.7$\mu\textrm{g}$/kg. The effects of drying methods in squid were found to be quite different. the levels of NDMA in traditionally dried products were 11~16 and 3~4 times higher than those in sun dried and hot-air dried products, respectively It is believed that high levels of NDMA were detected in traditionally dried products because NDMA was formed from reaction between various amines and nitrogen oxide produced by combustion of briquet during drying of squid.

• Journal of the Korean Applied Science and Technology
• /
• v.39 no.1
• /
• pp.108-114
• /
• 2022

In this study, the antioxidant effect of black sea ginseng containing a large amount of eicosapentaenoic acid, a natural physiologically active substance, was investigated, and its superiority as a functional cosmetic raw material was presented. The ability of the sea cucumber extract to remove active oxygen was evaluated for the inhibitory effect on intracellular nitric oxide (NO) production. The physiologically active substances of sea cucumber have an antioxidant effect that removes free radicals, and as a result of evaluation, it was confirmed that excellent NO production was suppressed. Studies have shown that bioactive substances are involved in antioxidant effects, immune and inflammatory response regulation by showing high antioxidant efficacy even at low concentrations. It is thought that the antioxidant removal ability of sea cucumber greatly contributes to the antioxidant efficacy of phenolic components containing EPA (eicosapentaenoic acid) of the sea cucumber extract. It was found to be similar to the report that the antioxidant component of sea cucumber works. In addition, it is excellent for wound healing with the eicosapentaenoic acid (EPA) component contained in a large amount of sea cucumber extract, which has been proven to be involved in the inhibitory effect of inflammatory activity. As a result of this study, it was confirmed that the effect of the phenol component contained in the sea cucumber extract had a close causal relationship with the antioxidant activity.

• Journal of the Korean Applied Science and Technology
• /
• v.39 no.1
• /
• pp.34-41
• /
• 2022

As the use of chemical products increases in daily life, the removal of dye waste has also emerged as an important environmental issue. This dye waste can be decomposed using a photocatalyst, and the photocatalyst can be synthesized very cost-effectively by using the sol-gel technology. The sol-gel technology is not only very useful for nanoscale film formation, but also can simply form multilayer structures. Using a multiple spin coating method, in this study, a ZnO film with a multilayered structure (3 layers, 5 layers) was formed by using zinc oxide (ZnO), which is effective in decomposing various dyes. For performance comparison, a ZnO film having a single layer structure by a single spin coating method was prepared as a control. Structural and elemental analysis of ZnO film was performed using an X-ray diffraction analyzer and an energy dispersive X-ray spectrometer. A nanowire-like surface morphology could be observed through a scanning electron microscope. Additionally, UV-Vis spectrophotometer was used to measure the absorbance of UV light. The ZnO film with a five-layer structure degraded the simulated methylene blue by 49% more than the ZnO film with a single-layer structure. In conclusion, it was found that ZnO having a multilayered structure is useful as a photocatalyst that decomposes methylene blue dye more effectively.