• Journal of Ceramic Processing Research
• /
• 제13권spc2호
• /
• pp.304-307
• /
• 2012

Nano-fibers of LiFePO4 were synthesized from a metal oxide precursor by adopting electrospinning method. After calcination of the above precursor nano-fibers at 800 ℃, LiFePO4 nano-fibers with a diameter of 300 ~ 800 nm, were successfully obtained. Measurement were performed using X-ray diffraction (XRD), fourier transform infrared spectrometer (FT-IR), videoscope, scanning electron microscope (SEM) and atomic force microscope (AFM), respectively, were performed to characterize the properties of the as-prepared materials. The results showed that the crystalline phase and morphology of the fibers were largely influenced the starting materials and electrospinning conditions.

• Bulletin of the Korean Chemical Society
• /
• 제34권9호
• /
• pp.2573-2576
• /
• 2013

Rate capability and cyclability of $LiMn_2O_4$ should be improved in order to use it as a cathode material of lithium-ion batteries for hybrid-electric-vehicles (HEV). To enhance the rate capability and cyclability of $LiMn_2O_4$, it was coated with $MnV_2O_6$ by a sol-gel method. A $V_2O_5$ sol was prepared by a melt-quenching method and the $LiMn_2O_4$ coated with the sol was heat-treated to obtain the $MnV_2O_6$ coating layer. Crystal structure and morphology of the samples were examined by X-ray diffraction, SEM and TEM. The electrochemical performances, including cyclability at $60^{\circ}C$, and rate capability of the bare and the coated $LiMn_2O_4$ were measured and compared. Overall, $MnV_2O_6$ coating on $LiMn_2O_4$ improves the cyclability at high temperature and rate capability at room temperature at the cost of discharge capacity. The improvement in cyclability at high temperature and the enhanced rate capability is believed to come from the reduced contact between the electrode, and electrolyte and higher electric conductivity of the coating layer. However, a dramatic decrease in discharge capacity would make it impractical to increase the coating amount above 3 wt %.

• 대한전자공학회논문지SD
• /
• 제38권12호
• /
• pp.1-7
• /
• 2001

낮은 동작전압에서 안정하게 동작하고 고효율을 갖는 단층 폴리머 녹색광소자를 갖는 새로운 물질을 합성하였으며 이는 폴리머물질인 PC(B79)에 유기단분자인 전자수송성이 ?어난 NIDI와 정공수송성이 뛰어난 TTA를 분자분산하여 첨가색소인 C6의 도핑농도에 변화를 주어 스핀코팅으로 녹색발광소자를 제작하였다. 소자 구조는 glass/ITO/PC:TTA:NIDI:C6/cathode이고 음극전극으로 일함수가 낮은 Ca과 Mg 그리고 Ca/Al을 진공증착하여 전기적${\cdot}$광학적 특성을 비교조사하였다. C6의 도핑농도가 0.08mole%에서 양자효율이 최대인 0.52%를 얻었고 이것은 도핑하지 않을때보다 약 50배 높았고, 동작개시전압도 2.4V의 낮은 동작 개시전압에서 안정하게 동작하였다. 한편 PL과 EL측정결과 C6의 도핑농도를 변화하여도 발광파장의 최대값은 거의 일정하였다. PL강도의 최대발광파장은 495nm였고 EL강도의 최대발광파장은 520nm이고 FWHM은 약 70nm를 얻었다.

• Transactions on Electrical and Electronic Materials
• /
• 제8권6호
• /
• pp.260-264
• /
• 2007

We have studied stability in organic light-emitting diode depending on buffer layer and cathode. A transparent electrode of indium-tin-oxide(ITO) was used as an anode. An electron injection energy barrier into organic material is different depending on a work function of cathodes. Theoretically, the energy barriers for the electron injection are 1.2 eV, -0.1 eV, and 0.0 eV for Al, LiAl, and LiF/Al at 300 K, respectively. We considered the cases that holes are injected to organic light-emitting diode. The hole injection energy barrier is about 0.7 eV between ITO and TPD without buffer layer. For hole-injection buffer layers of CuPc and PEDOT:PSS, the hole injection energy barriers are 0.4 eV and 0.5 eV, respectively. When the buffer layer of CuPc and PEDOT:PSS is existed, we observed the effects of hole injection energy barrier, and a reduction of operating-voltage. However, in case of PVK buffer layer, the hole injection energy barrier becomes high(1.0 eV). Even though the operating voltage becomes high, the efficiency is improved. A device structure for optimal lifetime condition is ITO/PEDOT:PSS/TPD/$Alq_3$/LiAl at an initial luminance of $300cd/m^2$.

• 한국세라믹학회지
• /
• 제56권5호
• /
• pp.497-505
• /
• 2019

Lanthanum-based transition metal cations containing perovskites have emerged as potential catalysts for the intermediate-temperature (600-800℃) oxygen reduction reaction (ORR). Here, we report a facile acetylacetone-assisted combustion route for the synthesis of nanostructured La_0.6Sr_0.4Co_0.2Fe_0.8O_3-δ (LSCF6428) cathodes for intermediate-temperature solid-oxide fuel cells (IT-SOFCs). The as-prepared powder was analyzed by thermogravimetry analysis-differential scanning calorimetry. The powder calcined at 800℃ was characterized by X-ray diffraction, scanning electrode microscopy, energy dispersive X-ray spectroscopy, and Brunauer-Emmett-Teller surface area measurements. It was found that the porosity of the air electrode significantly increased by utilizing the nanostructured LSCF6428 instead of commercial powder. The performance of a single cell fabricated with the nanostructured LSCF6428 cathode increased by 112%, from 0.4 to 0.85 W cm^-2, at 700℃. Electrochemical impedance spectroscopy showed a considerable reduction in the area-specific resistance and activation energy from 133.5 to 61.5 kJ/mol, resulting in enhanced electrocatalytic activity toward ORR and overall cell performance.

• Transactions on Electrical and Electronic Materials
• /
• 제16권3호
• /
• pp.124-129
• /
• 2015

Organic electronics are the domain in which the components and circuits are made of organic materials. This new electronics help to realize electronic and optoelectronic devices on flexible substrates. In recent years, organic materials have replaced conventional semiconductors in many electronic components such as, organic light-emitting diodes (OLEDs), organic field-effect transistors (OFETs) and organic photovoltaic (OPVs). It is well known that organic light emitting diodes (OLEDs) have many advantages in comparison with inorganic light-emitting diodes LEDs. These advantages include the low price of manufacturing, large area of electroluminescent display, uniform emission and lower the requirement for power. The aim of this paper is to model polymer LEDs and OLEDs made with small molecules for studying the electrical and optical characteristics. The purpose of this modeling process is, to obtain information about the running of OLEDs, as well as, the injection and charge transport mechanisms. The first simulation structure used in this paper is a mono layer device; typically consisting of the poly (2-methoxy-5(2'-ethyl) hexoxy-phenylenevinylene) (MEH-PPV) polymer sandwiched between an anode with a high work function, usually an indium tin oxide (ITO) substrate, and a cathode with a relatively low work function, such as Al. Electrons will then be injected from the cathode and recombine with electron holes injected from the anode, emitting light. In the second structure, we replaced MEH-PPV by tris (8-hydroxyquinolinato) aluminum (Alq₃). This simulation uses, the Poole-Frenkel -like mobility model and the Langevin bimolecular recombination model as the transport and recombination mechanism. These models are enabled in ATLAS- SILVACO. To optimize OLED performance, we propose to change some parameters in this device, such as doping concentration, thickness and electrode materials.

• 한국재료학회지
• /
• 제9권6호
• /
• pp.551-555
• /
• 1999

The deposition condition to obtain stoichiometric $Ta_2$O\ulcorner films, which is still controversial, using magnetron reactive sputtering was studied. The films were deposited by varying $O_2$gas flow rate with sputtering power and Ar gas flow rate of 200W and 60 sccm fixed. At the conditions of $O_2$ gas flow rate over 20 sccm, amorphous Tantalum oxide films with the refractive index of 2.1 and dielectric constant of 25 were deposited. Among those films, the capacitors dielectric properties of the film deposited at the condition of $O_2$ gas flow rate 50 sccm was best, the leakage current was 1$\times$10\ulcornerA/$\textrm{cm}^2$ at the electric field strength of 0.5 MC/cm and the breakdown field strength was over 2.0 MV/cm. This result could be explained from the analysis comparing with a standard sample using RBS because the composition of the film deposited at this condition was closest to the stoichiometric $Ta_2$O\ulcorner. The result of XPS analysis convinced that this film was stoichiometric $Ta_2$O\ulcorner film. A maximum cathode voltage was observed when $O_2$gas flow rate was 30 sccm. This shows that the Schiller's proposition that one can obtain stoichiometric films at the condition of maximum cathode voltage is not correct and more oxygen than that of the maximum voltage condition is necessary to deposit the stoichiometric Ta$_2$O\ulcorner films.

• Corrosion Science and Technology
• /
• 제20권6호
• /
• pp.451-465
• /
• 2021

In this investigation, electrochemical characteristics and damage behavior of 316L stainless steel polymer electrolyte membrane fuel cell(PEMFC) were analyzed by potentiodynamic and potentiostatic tests in cathode operating condition of PEMFC. As the result of potentiodynamic polarization test, range of passive region was larger than range of active region. In the result of potentiostatic test, damage depth and width, pit volume, and surface roughness were increased 1.57, 1.27, 2.48, and 1.34 times, respectively, at 1.2 V compared to 0.6 V at 24 hours. Also, as a result of linear regression analysis of damage depth and width graph, trend lines of damage depth and width according to applied potentials were 16.6 and 14.3 times larger, respectively. This demonstrated that applied potential had a greater effect on pitting damage depth of 316L stainless steel. The damage tendency values were 0.329 at 6 hours and 0.633 at 24 hours with applied potentials, representing rapid growth in depth direction according to the test times and applied potentials. Scanning electron microscopy images revealed that surface of specimen exhibited clear pitting damage with test times and applied potentials, which was thought to be because a stable oxide film was formed by Cr and Mo.

• 전기화학회지
• /
• 제4권2호
• /
• pp.58-64
• /
• 2001

기체/전해질/LSM $(La_{0.85}Sr_{0.15}MnO_3)$ 공기극이 만나는 삼상계면 (triple phase boundary) 주위에 YSZ ($8mol\%$ yttria stabilized zirconia) 코팅막 (coating film) 을 형성하여 추가로 삼상계면을 크게 늘린 새로운 전극 미세구조를 갖는 복합 공기극 (composite cathode) 을 개발하였다. 이 복합 공기극을 전해질 두께가 약 $30{\mu}m$인 연료극 (anode)v 지지체 위에 형성하여 $700\~800{\circ}C$의 온도에서 전류전압 특성 및 교류 임피던스 분석을 실시하였다. $800^{\circ}$, 공기 및 수소 조건에서 교류 임피던스 분석 결과 1000Hz주파수 영역을 대변하는 저항성분 R1은 연료극 분극 저항에 해당하였고 100Hz주파수 영역의 저항성분 R2는 공기극 분극 저항 성분, 그리고 10Hz이하 영역의 저항성분 R3는 전극을 통한 기체확산 저항성분으로 특히, 작동 조건인 공기 및 수소 분위기에서는 연료극 쪽 반응기체에 의한 기체확산 저항 성분임을 알 수 있었다. 전지성능 측정 결과 이 복합 공기극을 장착한 전지는 $800^{\circ}C$, 공기 및 산소 조건에서 각각 $0.55W/cm^2$ $1W/cm^2$의 높은 전지성능을 나타내었다. 전류전압 곡선은 기울기가 다른 두 구간으로 구분되었으며, 낮은 전류밀도 하에서 보이는 급격한 전압감소 구간은 공기극 분극저항이 주된 성능 저하의 원인인 반면, 높은 전류밀도 하에서 나타나는 완만한 전압 감소 구간은 전해질에 관련된 분극저항이 주된 성능 저하의 원인이었다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2005년도 춘계학술대회
• /
• pp.306-309
• /
• 2005

One of the most critical issues in sol id oxide fuel cell (SOFC)running on hydrocarbon fuels is the risk of carbon formation from the fuel gas. The simple method to reduce the risk of carbon formation from the reactions is to add steam to the fuel stream, leading to the carbon gasification react ion. However, the addition of steam to fuel is not appropriate for the auxiliary power unit (APU) and potable power generation (PPG) systems due to an increase of complexity and bulkiness. In this regard, many researchers have focused on so-called 'direct methane' operation of SOFC, which works with dry methane without coking. However, coking can be suppressed only by the operation with a high current density, which may be a drawback especially for the APU and PPG systems. The single chamber fuel cell (SC-SOFC) is a novel simplification of the conventional SOFC into which a premixed fuel/air mixture is introduced. It relies on the selectivity of the anode and cathode catalysts to generate a chemical potential gradient across the cell. Moreover it allows compact and seal-free stack design. In this study, we fabricated honeycomb type mixed-gas fuel cell (MGFC) which has advantages of stacking to the axial direction and increasing volume power density. Honeycomb-structured SOFC with four channels was prepared by dry pressing method. Two alternative channels were coated with electrolyte and cathode slurry in order to make cathodic reaction sites. We will discuss that the anode supported honeycomb type cell running on mixed gas condition.