• Laser Solutions
• /
• v.3 no.1
• /
• pp.38-45
• /
• 2000

A 4㎾ RS840 CO2 laser with a powder auto-feeding apparatus has been used to deposit multiple overlapping tracks of Ni-base superalloy on to low carbon steel. It was found that the surface roughness(turbulence) of an overlapped cladding layer decreased with the increase of the overlapping ratio in an oscillating manner. When the overlapping ratio had values of 0.62, the surface turbulence was lowest. Overlapping ratio offer significant potential for improvement of materials surface properties such as corrosion performance and wear resistance. This paper reports that the overlapping ratio shows best corrosion resistance. The tensile residual stresses generated at the higher overlapping ratio( ＞ 0.45) and the element concentration of Fe increased in the surface layer at the lower overlapping ratio( ＜ 0.45) may lead to worse corrosion resistance.

• Journal of electromagnetic engineering and science
• /
• v.2 no.1
• /
• pp.1-4
• /
• 2002

Performance improvement of the DS-CDMA system by the spectrum-overlap is important for better service quality or more system capacity. In this paper, an analysis thor capacity improvement is newly considered when the Lanczos chip waveform is used for the spectrum-overlapped DS-CDMA system. RC(relative capacity) is the ratio of the capacity of overlapping system to that of non-overlapping system, which is used for the expression of the capacity improvement. The optimal overlapping ratio is numerically found to make the maximum capacity improvement When the rectangular chip waveform is used far the overlapping system, maximum capacity improvement is increased by about 10% at the required BER=$10^{-3}$TEX> and the optimal overlapping ratio is 1.23. When the 95 % power bandwidth is considered for the Lanczos chip waveform, maximum capacity improvement is increased by 34.4% at overlapping ratio of 1.55 when the required BER is $10^{-3}$TEX>. The lower required BER far the better communication quality makes gradually smaller capacity improvement.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.23 no.3
• /
• pp.167-181
• /
• 2021

New type of rock excavation method using a waterjet system is being developed to secure economic feasibility and to reduce vibrations during excavation. In waterjet rock excavation, overlapping of cutting width is essential for high efficiency. In this study, cutting experiments for granite specimens were performed using abrasive waterjet system according to the overlapping ratio and standoff distance. Based on the experimental results, the granite cutting performance was analyzed according to the overlapping ratio. In addition, removal shapes of the cross-section were analyzed in terms of the cutting depth, width, and volume after waterjet cutting. When the overlapping ratio is less than 58%, rock specimens are partially removed due to the insufficient overlapping ratio. However, when the overlapping ratio exceeds 67%, overcutting phenomenon is observed. For the partial overlapping ratio (i.e., 25~75%), cutting efficiency is increased in the removal volume. This study is expected to be used as the important basic data for determining the optimum overlapping ratio when the waterjet system is applied for rock excavation.

• Journal of Broadcast Engineering
• /
• v.21 no.5
• /
• pp.816-823
• /
• 2016

This paper studies a light emitting diode(LED) overlapping method of a head-up display that consists of a digital micro device(DMD) panel and a red, green, blue LED in order to increase the brightness of display system and optical output power. This optimization overlapping method removes a quantization noise which occur due to LED overlapping too excessive and stabilizes the junction temperature of LED. In order to reduce junction temperature of LED, the a correlation between a green duty and LED overlapping ratio is studied. Throughout this study, the brightness of head-up display exhibited high increasement ratio of luminance around 33.3 percent at 39 percent overlapping method.

• Journal of information and communication convergence engineering
• /
• v.13 no.3
• /
• pp.215-219
• /
• 2015

Cells in a culture process transform with time and produce many overlapping cells in their vicinity. We are interested in a separation algorithm for images of overlapping cells taken using a fluorescence optical microscope system during a cell culture process. In this study, all cells are assumed to have an ellipse-like shape. For an ellipse fitting-based method, an improved least squares method is used by decomposing the design matrix into quadratic and linear parts for the separation of overlapping cells. Through various experiments, the improved least squares method (numerically stable direct least squares fitting [NSDLSF]) is compared with the conventional least squares method (direct least squares fitting [DLSF]). The results reveal that NSDLSF has a successful separation ratio with an average accuracy of 95% for two overlapping cells, an average accuracy of 91% for three overlapping cells, and about 82% accuracy for four overlapping cells.

• Transactions of Materials Processing
• /
• v.17 no.3
• /
• pp.203-209
• /
• 2008

In this paper, experimental investigation has been performed to analyze the forming process of toothed or serrated sheets, which is used as strap engaging surface of the seal to secure together overlapping portions of steel or plastic strapping ligature. Serration formed on the strap engaging surface of the seal prevent from relative slipping between overlapping ligatures after closing the seal. The geometry of tooth on the strap engaging surface is directly related to the quality of securing overlapping ligatures together. Inclined indentation followed by scratching operation has been proposed and applied to the experiments. Punch entry and face angles are selected as process variables to see the influence of these variables on the tooth geometry. Five different punch entry angles have been applied to experiments and three different punch face angles have been selected for each case of punch entry angle. Clay is selected as model material for experiments. Experimental results are summarized in terms of tooth height, tooth width, and aspect ratio such as tooth height to width ratio, respectively.

• Transactions of Materials Processing
• /
• v.20 no.8
• /
• pp.575-580
• /
• 2011

Direct laser melting(DLM) is promising as a joining method for producing parts for automobiles, aerospace, marine and medical applications. An advantageous characteristic of DLM is that it affects the parent metal very little. The mechanical properties of parts made by DLM are strongly affected by the porosity and surface roughness of the laser melted beads. This is a systematic study of the effects of the porosity and surface roughness of laser melted beads using various processing parameters, such as laser power, scan rate and overlapping ratio of the fill spacing. The specimens were fabricated with 316L and 304L austenitic stainless steel powder. Dense parts with low porosity were obtained at low laser scan speed, as it increased the aspect ratio of the parental material and the depth of penetration. The variations of surface roughness were examined at various processing parameters such as overlapping ratio and laser power.

• Journal of electromagnetic engineering and science
• /
• v.1 no.2
• /
• pp.120-125
• /
• 2001

The capacity improvement in the DS-CDMA system can be obtained by allowing spectrum-overlap between adjacent channels. In this paper, an analysis for capacity improvement is newly considered according to the various chip waveforms in the partial spectrum-overlapped DS-CDMA system. Optimum-overlapping ratio is numerically found to obtain maximum capacity improvement for each chip waveform. Assuming the bandwidth containing 95% of the total power, i.e., 95% power bandwidth, rectangular chip waveform has the largest capacity improvement in the considered chip waveforms and then the amount of improvement is 136.5% at overlapping ratio 1.5 for BER = $10^{-3}$TEX> . Furthermore, as the required BER becomes lower, the capacity improvement gets smaller for a1l of chip waveforms. For the unequal power channels, it is shown that the larger capacity improvement is achieved as the power of desired channel becomes larger than that of adjacent channels. And the capacity improvement can be obtained even though the desired channel power is lower than the adjacent channel power.

• Phonetics and Speech Sciences
• /
• v.2 no.2
• /
• pp.63-68
• /
• 2010

A new version of sequential probability ratio test (SPRT) which has been investigated in utterance-length control is proposed to obtain uniform response results in speaker verification (SV). Although SPRTs can obtain fast responses in SV tests, differences in the performance may occur depending on the compositions of consonants and vowels in the sentences used. In this paper, a fast sequential probability ratio test (FSPRT) method that shows consistent performances at all times regardless of the compositions of vocalized sentences for SV will be proposed. In generating frames, the FSPRT will first conduct SV test processes with only generated frames without any overlapping and if the results do not satisfy discrimination criteria, the FSPRT will sequentially use frames applied with overlapping. With the progress of processes as such, the test will not be affected by the compositions of sentences for SV and thus fast response outcomes and even consistent performances can be obtained. Experimental results show that the FSPRT has better performance to the SPRT method while requiring less complexity with equal error rates (EER).

• Proceedings of the KWS Conference
• /
• 2000.04a
• /
• pp.131-134
• /
• 2000