• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 1999년도 춘계 학술대회논문집
• /
• pp.85-89
• /
• 1999

Numerical Analysis has been done for the supersonic off-design jet flow due to the pressure difference between the jet and the ambient fluid. The difference of pressure generates an oblique shock or an expansion wave at the nozzle exit, The waves reflect repeatedly at the center axis and on the sonic surface in the shear layer, and the pressure difference is resolved across these waves interacted with the turbulence mixing layer. In this paper, the axi-symmetric Navier-Stokes equation has been used with two equation $k-{\varepsilon}$ turbulence closure model. The second order TVD scheme with flux limiters, based on the flux vector split by the smooth eigenvalue split, has been used to capture internal shocks and other discontinuities. The correction term for the compressible flow and the damping function are used in the turbulence model. Numerical calculations have been done to analyze the off-design jet flow due to the pressure difference. The variation of pressure along the flow axis is compared with an experimental result and other numerical result. The characteristics of the interaction between the shock cell and the turbulence mixing layer have been analyzed.

• 대한기계학회논문집B
• /
• 제32권12호
• /
• pp.945-953
• /
• 2008

Laminar film condensation of saturated vapor in forced flow over a flat plate is analysed. The problem is formulated as exact boundary-layer solution and integral approximate solution. From numerical solutions of the governing equations, it is found that the energy transfer by convection and the effect of inertia term in the momentum equation in negligibly small for low pressure but quite important for high pressure. The condensate rate, liquid-vapor interfacial shear stress and local heat transfer are strongly dependent on the reduced pressure $P_r$ and the modified Jacob number Ja/Pr.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 추계학술대회 논문집
• /
• pp.9-12
• /
• 1997

The fabrication and performance of a thin film pressure sensor are described. Cu-Ni thin film strain gauges have been fabricated by RF magnetron sputtering. For all the gauges, the relative chance in resistance ΔR/R with pressure is of the order 10$^{-3}$ for the maximum pressure. The output characteristic is found to be linear over the entire Pressure range (0-30kgf/cm$^2$) and the output sensitivity is 1.6 mV/V. The maximum nonlinearity observed in output characteristics is 0.34%FS for 5V excitation and the hysteresis is less than 0.1%FS.

• Bulletin of the Korean Chemical Society
• /
• 제5권3호
• /
• pp.112-117
• /
• 1984

The association constants (K) of 3,5,N-trimethyl pyridinium iodide in 95 volume percent ethanol-water mixed solvent were determined by a modified UV and conductance method at $25^{\circ},\;30{\circ},\;40{\circ}\;and\;50{\circ}C$ over the pressure range 1 to 2000 bars. The association process is enhanced with increasing pressure and decreasing temperature. From K values, we obtained the total partial molar volume change (${\Delta}V$) and some thermodynamic parameters. The electrostriction volume (${\Delta}V_{el}$) and intrinsic volume (${\Delta}V_{in}$) were also evaluated. The values of ${\Delta}V,\;{\Delta}V_{el},\;{\Delta}V_{in}$ are negative, negative and positive, respectively, and the absolute values of all these three decrease with increasing pressure and temperature. The ion-pair size (a) were varied 3 to 6 ${\AA}$, with pressure and temperature. The solvation number (n) decreased from 2 to 0.5 with increasing temperature.

• 반도체디스플레이기술학회지
• /
• 제8권2호
• /
• pp.15-21
• /
• 2009

Atmospheric pressure plasma equipment was successfully applied to the flip chip BGA manufacturing process to improve the uniformity of flux printing process. The problem was characterized as shrinkage of the printed flux layer due to insufficient surface energy of the flip chip BGA substrate. To improve the hydrophilic characteristics of the flip chip BGA substrate, remote DBD type atmospheric pressure plasma equipment was developed and adapted to the flux print process. The equipment enhanced the surface energy of the substrate to reasonable level and made the flux be distributed over the entire flip chip BGA substrate uniformly. This research was the first adaptation of the atmospheric pressure plasma equipment to the flip chip BGA manufacturing process and a lot of possible applications are supposed to be extended to other PCB manufacturing processes such as organic cleaning, etc.

• 센서학회지
• /
• 제16권1호
• /
• pp.44-51
• /
• 2007

A hybridized simulator for generating blood pressure waveform is proposed to study the remedy and/or evaluation of the conventional sphygmomanometer utilizing the oscillometric method which is widely applied. The blood pressure of a flowing fluid was controlled for the blood vessel's condition caused by a rhythmical and periodical contraction/relaxation because of the special excitatory and conductive system of the heart. In this study, a hybridized controller composed of the PI feedback controller and the feedforward controller. The inverse dynamics function is proposed to operating the control valve while the pressure is applied in an oil pressure tank. The proposed hybrid simulator reproducing the blood pressure waveform in an artificial blood vessel has kept the control performance consistent over all range. Based on these results, the proposed simulators could be applied to the development and compensation of the non invasive sphygmomanometer type as well as to study the characteristics of the blood pressure and blood vessel.

• 대한기계학회논문집A
• /
• 제26권8호
• /
• pp.1552-1564
• /
• 2002

Meter-in, meter-out and bleed-off circuits are widely utilized in order to adjust the speed of a hydraulic actuator by using a flow control valve and in order to regulate the pressure of a hydraulic volume by using a simple on-off valve. In these circuits, a relief valve serves either to maintain constant system pressure or to protect the system from over-pressure loading. The relief valve of a bleed-off circuit is the second case frequently undergoing on-off action during operation. It makes the analysis of the pressure control characteristics of the circuit highly difficult. In this paper, steady-state flow rate, pressure, heat loss and efficiency of the three circuits are reexamined and basic experiments far obtaining the characteristics of a pump and relief valve are conducted. Finally, simple empirical first-order dynamic models of decreasing and increasing pressure were separately proposed and verified by comparison with experiment. As the result, the basis for the theoretical analysis of the pressure control characteristics of a bleed-off circuit using a simple on-off valve is established.

• 한국분무공학회지
• /
• 제16권1호
• /
• pp.7-14
• /
• 2011

High pressure LPG fuel spray with a conventional swirl injector was visualized and the impact of the injection pressure was also investigated using a DISI (direct injection spark ignition) LPG single cylinder engine. Engine performance and emission characteristics were evaluated over three different injection pressure and engine loads at an engine speed of 1500 rpm. The fuel spray pattern appeared to notably have longer penetration length and narrower spray angle than those of gasoline due to its lower angular momentum and rapid vaporization. Fuel injection pressure did not affect combustion behaviors but for high injection pressure and low load condition ($P_{inj}$=120 bar and 2 bar IMEP), which was expected weak flow field configuration and low pressure inside the cylinder. In terms of nano particle formation the positions of peak values in particle size distributions were not also changed regardless of the injection pressure, and its number densities were dramatically reduced compared to those of gasoline.

• 한국산학기술학회논문지
• /
• 제7권3호
• /
• pp.285-290
• /
• 2006

자동차에 있어서 안전은 가장 중요한 설계 인자이다. 자동차 타이어 압력은 자동차 안전에 중요한 요소로 알려져 있다. 능동적 안전 측면에서, 타이어공기압검지장치(TPMS)는 아주 중요한 요소라 할 수 있다. RF 통신 기능을 갖고 타이어 내부에서 타이어 압력을 모니터링하는 장치는 광범위한 운전영역에서 정회한 압력을 검지하는 효과적 방법이다. 본 논문에서는 타이어 압력 및 온도보상 특성 관계를 조사하였다. 본 연구를 통하여, 차량 조건과 주행 변수를 고려한 TPMS 제어 로직의 가이드 라인을 설정할 수 있었다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제5권2호
• /
• pp.51-57
• /
• 2003

This paper proposes a new oscillating flow model of the pressure drop through the regenerator under pulsating pressure. In this oscillating flow model. pressure drop is expressed by the amplitude and the phase angle with respect to the inlet mass flow rate. In order to generalize the oscillating flow model. non-dimensional parameters, which are Reynolds number, Valensi number, gas domain length ratio, oscillating flow friction factor and phase angle of pressure drop, are derived from the capillary tube model of the regenerator. Correlations for the oscillating flow friction factor and the phase angle are obtained from the experiments for the twill-square screen regenerators under various operating frequencies and inlet mass flow rates. The oscillating friction factor is a function of the Reynolds number alone and the phase angle of pressure drop is a function of the Valensi number and the gas domain length ratio. Experiment is also performed to examine the effect of the weave style of screen. Experimental data demonstrate the superiority of the oscillating flow model over the previous steady flow model.