• 한국세라믹학회지
• /
• 제32권3호
• /
• pp.281-288
• /
• 1995

to prepare the TiO2 thin films, acetyl-acetone(2.4-pentanedione)(1 : 1 molar ratio) was dissolved in the propanol solution of titanium(IV)isopropoxide(Ti[OCH(CH3)2]4). Al, Cr and Sb in the form of soluble salt and niobium ethoxide were added s dopants, respectively. Thin films were coated by the dip-coating method and characteristics were investigated by XRD, SEM and conductance meter. As a result, viscosity of sol was maintained below 4 centi Poise more than 20 days, and crystal growth and diminution of resistivity occurred as the heat treatment temperature increased. The grains grew over 1${\mu}{\textrm}{m}$ and the lowest resistivity was obtained when Nb was added at 130$0^{\circ}C$.

• 한국고분자학회:학술대회논문집
• /
• 한국고분자학회 2006년도 IUPAC International Symposium on Advanced Polymers for Emerging Technologies
• /
• pp.354-354
• /
• 2006

Alginic acid-silica hydrogel films was prepared for testing as protective coating materials for PTFE OD membranes. Unprotected hydrophobic membranes are subject to wet-out when contacted by surface-active agents. Films were characterised using SEM, XRD, DSC, mechanical strength measurements, and water-swelling measurements. In OD trials using coated membranes, no wet-out occurred over the 15 h duration of three consecutive 5 h OD trials using orange oil-water mixtures. In the case of detergent solutions, the coating afforded protection to the membrane for 4-5 h. In a separate trial, no wet-out occurred when the coated side of the membrane was placed in contact with 1.2 wt % orange oil for 72 hours.

• Tribology and Lubricants
• /
• 제10권4호
• /
• pp.69-74
• /
• 1994

The space world under zero gravity and super vacuum where the space machine works has only friction and inertia. Inertia of acceleration and diceleration is accurately obtained by computing while friction is always in contact surface and unsteady. The sur soundings under super vacuum make surface friction more complicate. [1,2]. Therefore, method to lubricate stably the contact surface for long term in space machine is very important and friction for space machine proves to be true by several accident of space projects. In spite of that accident, method of lubrication and lubricants to keep stablity for long term in space machine have not been established so far. Lubrication for space machine is very important and under developings over the world. In this study we suggest a new lubricating technology, which improves powerful for space machine.

• 열처리공학회지
• /
• 제5권1호
• /
• pp.1-12
• /
• 1992

In order to improve adhesive force of TiN film, we sputtered titanium as interlayer before TiN deposition by Plasma Enhanced Chemical Vapour Deposition. We observed changes of hardness and adhesion at a various thickness of titanium interlayer and also examined analysis. At the critical thickness of the titanium interlayer(about $0.2{\mu}$), adhesive force of TiN films were promoted mostly. But over the critical thickness, a marked reduction of adhesive force was showed, because of the internal stress of titanium interlayer. From AES analysis, the adhesion improvement of TiN films was mainly caused by nitrogen diffusion into titanium interlayer during TiN deposition process which relieved stress concentration at TiN coating-substrate interface.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1988년도 전기.전자공학 학술대회 논문집
• /
• pp.792-795
• /
• 1988

Titanium dioxide antireflection (AR) Coating, which is deposited on Si substrates using an organotitanium solution by the spinning technique, has been studied. The coated films on Si substrates were subsequently heated to $450^{\circ}C$. The thickness and index of refraction of films were varied continuousely from $740{\AA}$ to $1380{\AA}$ and from 1.7 to 2.1 respectively as a function of heat treatment temperature and time. Silicon solar cells AR-coated by the spinning technique showed as much as 31% improvement in conversion efficiency over the uncoated cell.

• 대한가정학회지
• /
• 제40권10호
• /
• pp.77-85
• /
• 2002

This study was conducted to evaluate the efficiency of various fabrics in protecting from solar radiation and ultraviolet radiation(UV). Six kinds of fabrics were selected and examined in singles or doubles. It was studied how the materials and the thickness of air layer between the fabric and the floor affected the protection efficiency of fabrics from sunlight. The results were as followes; 1) Protection from solar radiation: In the case of over 2 cm air layer, doubled fabric composed of aluminum coating-nylon and white or black polyester/cotton(T/C) was the most protective(p<0.001). In the case of 0 cm air layer, the case without fabric and white T/C were more effective(p<0.001). And the thicker the air layer the more effective the protection. 2) Protection from UV : Doubled fabric composed of aluminum coating-nylon and black T/C was the most protective(p<0.001) and the thinner the air layer the more effective the protection(p<0.001).

• 한국초전도ㆍ저온공학회논문지
• /
• 제10권1호
• /
• pp.6-9
• /
• 2008

We have investigated the MOD process successfully for the fabrication of the YBCO thick film on the $LaAlO_3$(001) single crystalline substrate. The cracking problem in YBCO thick film, a serious problem in the conventional TFA-MOD method, could be overcome with a careful control of precursor materials. Thus coating solution was prepared for the YBCO thick film by using fluorine-free precursor material. The precursor solutions were coated on the LAO(001) single crystalline substrate using the dip coating method, calcined at the temperature up to $500^{\circ}C$, and fired at various high temperatures for 2 h in a reduced oxygen atmosphere. Optimally processed YBCO thick film exhibited high critical current($I_c$) over 200 A/cm-width at 77K in self-field.

• Restorative Dentistry and Endodontics
• /
• 제20권1호
• /
• pp.1-16
• /
• 1995

The purpose of this study was to investigate the effect of dentin bonding agents on the bond strength of composite resin restorations in case of applying the dentin bonding agents to acid etched enamel surfaces. Freshly extracted 364 bovine anterior teeth were selected as a adherents. 320 enamel specimens were divided into two groups(unetched group (1) and etched group (2) for testing the shear bond strength, 40 specimens were used for the hardness testing, and 4 specimens of rest were to observe the resin-tag formation into etched enamel surfaces. All surfaces of enamel specimens were polished with 320~1500 SiC paper under continuous running water. In Group (1), 100 enamel specimens were polished and unetched. 220 polished enamel specimens in Group (2) were etched with 37 % phosphoric acid solution for 60 seconds, washed with water for 20 seconds, and dried with a light air pressure for 60 seconds. Three kinds of dentin bonding agents(Gluma, Prisma, Scotchbond 2) were evaluated the effect on the bond strength to conditioned enamel surfaces. Shear bond strengths were measured on the three cases such as a coating of primer only, a coating of sealer only, and a sequential coating of primer and sealer to acid etched enamel surfaces were compared with the bond strengths measured by the coating of enamel bonding agent followed by the bonding of composite resin (Photo clearfil bright, Kuraray, Japan) to unetched and acid etched enamel surfaces. In addition, the hardness tested on the adhesive fractured surface between composite resin enamel as a mean of evaluation of a factor whether the mechanical bond strengths were affected and the penetration of dentin bonding agents into etched enamel surfaces was also observed. Bond strengths were measured using the method of shear bond strength by a universal testing machine (Instron-4467, USA), statistical test were applied to the results using a one way analysis variance(ANOVA), and hardness was measured by the Vicker's Hardness Tester(MHT-i, Matsuzawa, Japan) and the penetration of the resins were observed by the SEM (Hitachi, S-2300, Japan). The following conclusions were drawn; 1. Enamel bonding agent showed to affect the improvement of bond strength of composite resin to enamel surface both unetched and etched. 2. Dentin bonding agents could be resulted in increase of bond strength to unetched enamel surface, but there were no statistical significances. 3. Bond strengths to etched enamel surface were significantly decreased with a coating of dentin primer only. 4. Coating of sealer only and coating of primer and sealer noticed the similar bond strengths of composite resin to etched enamel using the enamel bonding agents. 5. The applying method proved to be more effective than the kinds of dentin bonding agents on the bond strength of composite resin to etched enamel than the kind of dentin. 6. Vicker's hardness numbers of dentin bonding agents were lower than that of composite resin, but the degree of penetration of dentin bonding agents into etched enamel surfaces was excellent.

• 한국재료학회지
• /
• 제22권12호
• /
• pp.696-700
• /
• 2012

(Na, K) $NbO_3$ thick film was successfully achieved using a sol-gel coating process with the addition of polyvinylpyrrolidone (PVP) to a metal alkoxide solution. The transparent coating solution, mixed with Nb:PVP = 1:1 in a molar ration, was synthesized by evaporating the solvent to over 62.5 wt%. Additive PVP increased the viscosity of the solution so that the coating thickness could be enhanced. The thickness of the (Na, K) $NbO_3$ film assisted by PVP was ca. 320 nm at the time of deposition; this value is four times thicker than that of the sample fabricated without PVP. Also, due to PVP binding with the OH groups of the metal alkoxide, the condensation reaction in the film was suppressed. The crystalline size of the (Na, K) $NbO_3$ films assisted by PVP was ca. 15 nm smaller than that of the film fabricated without PVP. After the sintering process at $700^{\circ}C$, the (Na, K) $NbO_3$ films were mainly composed of randomly oriented (Na, K) $NbO_3$ phase of perovskite crystal structure, including a somewhat secondary phase of $K_2Nb_4O_{11}$. However, by adding PVP, the content of the secondary phase became quite smaller than that of the sample without PVP. It was thought that the addition of PVP might have the effect of restraining the loss of potassium and that PVP could hold metalloxane by strong hydrogen bonding before complete decomposition. Therefore, the film thickness of the (Na, K) $NbO_3$ films could be considerably advanced and made more crack-free by the addition of PVP.

• Archives of Plastic Surgery
• /
• 제42권2호
• /
• pp.186-193
• /
• 2015

Background Polyurethane coating of breast implants has been shown to reduce capsular contracture in short-term follow-up studies. This 30-year study is the longest examination of the use of polyurethane-coated implants and their correlation with capsular contracture. Methods This study evaluates the senior surgeon's (F.D.P.) experience with the use of polyurethane-coated implants in aesthetic breast augmentation in 382 patients over 30 years. Follow-up evaluations were conducted for six months after surgery. After the six-month follow-up period, 76 patients returned for reoperation. The gross findings, histology, and associated capsular contracture were noted at the time of explantation. Results No patient during the six-month follow-up period demonstrated capsular contracture. For those who underwent reoperation for capsular contracture, Baker II/III contractures were noted nine to 10 years after surgery and Baker IV contractures were noted 12 to 21 years after surgery. None of the explanted implants had macroscopic evidence of polyurethane, which was only found during the first five years after surgery. The microscopic presence of polyurethane was noted in all capsules up to 30 years after the original operation. Conclusions An inverse correlation was found between the amount of polyurethane coating on the implant and the occurrence of capsular contracture. Increasingly severe capsular contracture was associated with a decreased amount of polyurethane coating on the surface of the implants. No contracture occurred in patients whose implants showed incomplete biodegradation of polyurethane, as indicated by the visible presence of polyurethane coating. We recommend research to find a non-toxic, non-biodegradable synthetic material as an alternative to polyurethane.