• Journal of the Korean Vacuum Society
• /
• v.18 no.2
• /
• pp.102-107
• /
• 2009

We investigated optical emission of oxygen plasma discharged by 13.56 MHz radio frequency (rf) by using optical emission spectroscopy (OES). Experimental measurement is done at a range of oxygen flow rate of 1$\sim$20 seem, rf power of 25$\sim$250 W, and orifice 3 and 5 mm in diameter. When oxygen plasma was generated, typical emission spectra for oxygen plasma were observed regardless of diameter of orifice. Strong atomic emission lines are observe at 776.8 an 843.9 nm, corresponding to the $3p^{5}P-3s^{5}S^{0}$ and $3p^{3}P-3s^{3}S^{0}$ transitions, respectively. The emission intensity of line at 776.8 and 843.9 nm increased with increasing the oxygen flow rate and rf power. The increasing rate of emission intensity of 776.8 nm line was larger than that of 843.9 nm line. When the diameter of orifice was 3 mm, the oxygen plasma was more stably generated than orifice 5 mm in diameter.

• Korean Journal of Agricultural Science
• /
• v.11 no.2
• /
• pp.284-294
• /
• 1984

Effects of orifice diameter, operating angle and swirl chamber distance were examined to study a reasonable distribution pattern on the maximum available travel distance in the triple nozzle system. The results of the study were as follows; 1. Discharge rate was increased with increase of orifice diameter, and a quadratic line for the 1st nozzle and linear lines for the 2nd or the 3rd nozzle. 2. The operating angle of $15^{\circ}$ had showed the maximum available travel distance, and 17m in orifice diameter of 3.0mm and operating pressure of $24.5{\times}10^5pa$ ($25Kg/cm^2$). 3. Nozzle setting methods (reference Table 6.) for improvement of uniformity of deposit distribution were varied depending on the size of orifice diameter of the 1st nozzle, nevertheless coefficients of uniformity were improved about 6 percents. 4. Adjustment of the swirl chamber distance of the 2nd nozzle could improve the minimum area of about 6m from the triple nozzle.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.1
• /
• pp.98-104
• /
• 2015

This experiment was a study of a Vortex nozzle designed to produce micro-bubbles due To investigate air self-suction and the generation of micro-bubble by the Vortex nozzle, the dimensions of air intake region, the nozzle shape, and the nozzle exit diameter ($d_n=5,7,9.2,12.3mm$)werevaried. The air self-suction rate was ~1,000 to 2,000 cc/min at the orifice nozzle (7 mm), and ~100 and ~22 cc/min at the sector nozzles (9.2 and 12.3 mm, respectively). The most bubbles were detected in the orifice nozzle, but bubbles less than $50{\mu}m$ were found in the 12.3-mm sector nozzle. The dissolved oxygen in the tank water was much greater in Case 2 than in Case 1, at both the orifice and sector nozzles. Moreover, the reduction rate of dissolved oxygen was found to be less at the sector nozzles, than at the orifice nozzle.

• The KSFM Journal of Fluid Machinery
• /
• v.19 no.5
• /
• pp.28-34
• /
• 2016

Though a peristaltic pump is a crucial element in miniaturized drug delivery systems, it has some intrinsic disadvantages such as backflow and flow fluctuation. To overcome these limitation, we have developed valve-less peristaltic pump system including orifice and stagnation chamber. we measured flow rate to investigate the performance of rotary peristaltic pump with three rollers and an elastomeric tube pumping a viscous fluid. The flow fluctuations and the backflow happen as a result from the disengagement of the contact interaction between the rollers and the tubes. Stagnation chamber installed in front of orifice plate was composed of rubber tube and gas chamber. By changing orifice hole diameter with stagnation chamber flow rate and pressure in the tube was regulated. The obtained maximum reduction ratio of flow fluctuation is 96.79%.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.4
• /
• pp.1501-1509
• /
• 1996

Differential pressure devices such as an orifice and Venturi are widely used in the measurement of flow rate of fluid mainly due to cost effectiveness and easy installation. In the current study, the viscoelastic effect on discharge and loss coefficients of those flow meters were investigated experimentally. Aqueous solutions of Polyacrylamide (200, 500, and 800 ppm) as viscoelastic fluids were used. Discharge coefficient of an orifice for viscoelastic fluids increased significantly up to approximately 15-20% when compared with that for water, while loss coefficient decreased up to 10-25% depending on the diameter ratio, .betha.. Also, pressure recovery for viscoelastic fluids was extended much longer than that for water. On the other hand, discharge and loss coefficients of Venturi for viscoelastic fluids were found to be strongly dependent on the Reynolds number. In both flow meters, the concentration effect for discharge and loss coefficients was not observed at more over than 200 ppm of aqueous solution. Conclusively, orifice and Venturi flow meters should be calibrated very carefully in the flow rate measurement for viscoelastic fluids.

• Journal of Drive and Control
• /
• v.9 no.3
• /
• pp.23-28
• /
• 2012

In this study the flow rate-to-pressure difference characteristics of short-tube type damping orifices for an aircraft door damper were investigated by CFD analyses and experiments. As the design parameters of the damping orifice its diameter, inlet and outlet angle, tube length and the viscosity of the working fluid were taken into consideration. The results showed that the discharge coefficient of the orifices are dependant on the inlet and outlet angle and the oil viscosity, while their length plays an little significant role. Although the short-tube type damping orifice was employed to induce a turbulent flow, their discharge coefficient decreases rapidly as the oil viscosity gets higher than 50mm2/s. Therefore, in order to determine the orifice size, satisfying the working temperature range of the door damper, the oil viscosity as well as the friction force on the damper piston should be kept within proper values. For the verification of the CFD analysis results the actual performance of a door damper was measured and compared with them.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.3
• /
• pp.1061-1073
• /
• 1996

Vortex tube is a simple device which splits a compressed gas stream into a cold stream and a hot stream without any chemical reactions. The phenomena of energy separation taking place in a vortex tube has been investigated experimentally. Recently, vortex tube is widely used to local cooler of industrial equipments and air conditioner of special purpose. In this study, experimental study on vortex tube efficiency was performed with various cold end orifices and nozzles type. The experimental results indicate that there is an optimum diameter of cold end orifice and nozzle type for the best cooling performance. The variation of the maximum wall temperature along the vortex tube surface provides useful information about the location of the stagnation point of the flow field at the axis of the vortex tube. The similarity relation for the prediction of the temperature of the cold exit air was obtained.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.949-952
• /
• 2017

Spray characteristics of the impinging injectors in subsonic crossflows were experimentally studied and compared with the plain-orifice injectors. By changing the impingement angle (60, 90, 120) which is the same orifice length to diameter ratio (L/d = 5), spray characteristics were investigated. In the view of the top view from the impinging injectors, as the impingement angle increases, the liquid column breakup length in the y-direction was decreased. On the other hand, when the impinging injector is viewed from the side view, the breakup length in the x direction is smaller than the previous plain-orifice injectors, which mean that the atomizing performance of the impingement-type injector is better than that of the single-hole orifice.

• Journal of Veterinary Clinics
• /
• v.30 no.2
• /
• pp.123-126
• /
• 2013

A 3-month-old male domestic shorthair cat was presented for evaluation of stranguria and hematuria and a 4-year-old male domestic shorthair cat was presented for evaluation of stranguria. For cat 1, a swollen prepuce, erythematous preputial orifice, and urine pooling from the preputial orifice were noted. The preputial orifice was a pinpoint opening and penis was not extruded from the prepuce. For cat 2, a necrotic skin around the preputial orifice, small preputial orifice, and severe urine pooling from the preputial orifice were noted. The round-shaped resection of the tip of the prepuce was performed to increase the diameter of the preputial orifice and remove erythematous fragile skin or a necrotic skin around the preputial orifice and the edematous, redundant preputial mucosa in these 2 cats. The preputial mucosa was then apposed to the ipsilateral incised skin edge. There was no recurrence of clinical signs over 22- and 24-month follow-up period, respectively. The round-shaped resection technique provided adequate enlargement of the preputial orifice to allow extrusion of penis in these 2 cats with a phimosis. This technique could be helpful in cases with skin and mucosa necrosis around the preputial orifice that require round-shaped resection.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.13 no.8
• /
• pp.667-673
• /
• 2001

As an alternative cooling method to reduce environmental hazard, vortex tubes have been studied for energy separation into cold and hot streams. Hence, the experiments were carried out systematically to find the best ratio of vortex chamber diameter to tube diameter. Also, the work was don to investigate how inlet pressure and geometric ratios of vortex tube affected temperature differences at tow needs as ell as cooling capacity and cooling efficiency. The result showed that the maximum temperature differences at the both ends and the maximum cooling efficiency were obtained when the ratio of vortex chamber diameter was about 1.45, while the inlet pressure ws not higher than 0.7 MPa.