• Journal of Ocean Engineering and Technology
• /
• v.25 no.6
• /
• pp.56-59
• /
• 2011

The demand for cold rolled steel (CR) for structural members is gradually increasing. If no surface treatment (coating for corrosion resistance) for CR is conducted, its use is very limited because CR is vulnerable to corrosion. Therefore, we need to develop a coating solution to provide high corrosion resistance for CR. In this study, an organic/inorganic coating solution with Si and Ti (Si polysilicate 7 wt.% + Urethane 13 wt.% + Ti amorphous 0.5 wt.%; LR-0727(1)) was used to evaluate the corrosion resistance of CR under a salt spray test. The specimens with the LR-0727(1) coating were heat treated in a drying oven at $120{\sim}210^{\circ}C$for 5 min. The corrosion resistance was investigated using a salt spray test of 7 h. In addition, an adhesive test was conducted. Rust showed under a heat treatment of $150^{\circ}C$, but no vestiges were found over $160^{\circ}C$. The specimens with heat treatment at $160^{\circ}C$ or more did not experience delamination. From these results, it is considered that the temperature limit for optimum heat treatment is $160^{\circ}C$ considering energy efficiency.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.154.2-154.2
• /
• 2016

In this work, we introduce a solution-processed CdS interlayer for use in inverted bulk heterojunction (BHJ) solar cells, and compare this material to a series of standard organic and inorganic cathode interlayers. Different combinations of solution-processed CdS, ZnO and conjugated polyelectrolyte (CPE) layers were compared as cathode interlayers on ITO substrates to construct inverted solar cells based on $PTB7:PC_{71}BM$ and a $P3HT:PC_{61}BM$ as photoactive layers. Introduction of a CdS interlayer significantly improved the power conversion efficiency (PCE) of inverted $PTB7:PC_{71}BM$ devices from 2.0% to 4.9%, however, this efficiency was still fairly low compared to benchmark ZnO or CPE interlayers due to a low open circuit voltage ($V_{OC}$), stemming from the deep conduction band energy of CdS. The $V_{OC}$ was greatly improved by introducing an interfacial dipole (CPE) layer on top of the CdS layer, yielding outstanding diode characteristics and a PCE of 6.8%. The best performing interlayer, however, was a single CPE layer alone, which yielded a $V_{OC}$ of 0.727 V, a FF of 63.2%, and a PCE of 7.89%. Using $P3HT:PC_{61}BM$ as an active layer, similar trends were observed. Solar cells without the cathode interlayer yielded a PCE of 0.46% with a poor $V_{OC}$ of 0.197 V and FF of 34.3%. In contrast, the use of hybrid ZnO/CPE layer as the cathode interlayer considerably improved the $V_{OC}$ of 0.599 V and FF of 53.3%, resulting the PCE of 2.99%. Our results indicate that the CdS layer yields excellent diode characteristics, however, performs slightly worse than benchmark ZnO and CPE layers in solar cell devices due to parasitic absorption below 550 nm. These results suggest that the hybrid inorganic/organic interlayer materials are promising candidates as cathode interlayers for high efficiency inverted solar cells through the modification of interface contacts.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.4
• /
• pp.647-651
• /
• 2007

In order to investigate the excited-state intramolecular proton transfer (ESIPT) process of dihydroxyanthraquinones (DHAQ; 1,5-DHAQ and 1,8-DHAQ) in organic-inorganic hybrid matrices, transparent SiO2, SiO2- Al2O3, and Al2O3 matrices chemically bonded with DHAQ were prepared using a sol-gel technique. The absorption maxima of 1,5- and 1,8-DHAQ in SiO2 matrices are observed at around 420 nm, whereas those of DHAQ in both SiO2-Al2O3 and Al2O3 matrices are markedly shifted to longer wavelength compared with those in SiO2 matrix. This indicates that DAHQ forms a chemical bond with an Al atom of Al2O3. The DHAQ in SiO2 matrix shows a markedly Stokes-shifted emission which is originated from the ESIPT in DHAQ. Based on the emission lifetimes of DHAQ, the ESIPT of DHAQ was found to be strongly affected by the chemical interaction with Al atom in the Al2O3-related matrices.

• Textile Coloration and Finishing
• /
• v.20 no.1
• /
• pp.44-47
• /
• 2008

Organic semi-conductive materials have characteristics such as the advantages of easy formability, low-cost and diversity along with moderate semi-conductive properties. In this paper, we developed a flexible organic-inorganic hybrid solar cell fiber. First, we made a solar cell on the glass and attached the solar cell on the glass fiber similarly. In the latter case, thermal deposition method was employed in order to effectively apply ITO onto fiber surface. The amount of ITO was controlled by varying the temperature from 25, 150 to $300^{\circ}C$. Optimum result was obtained at $150^{\circ}C$ where maximize the deposition amount without significant decomposition of ITO. Despite of maximum open circuit voltage of 0.39V, the resulting current was quite unstable and weak, limiting realistic applications. It was, however, concluded that the flexible solar cell fiber developed showed a possibility of low-weight application from functional clothing for military to space suit mainly due to flexibility and thus wear ability.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.11a
• /
• pp.87-90
• /
• 2005

This paper presents an evaluation of the effect of titanium dioxide nanoparticles in sulfonated poly(ether ether ketone) (SPEEK) with sulfonation degree of 57%. A series of inorganic-organic hybrid membranes were prepared with a systematic variation of titanium dioxide nanoparticles content. Their water uptake, methanol permeability and proton conductivity as a function of temperature were investigated. The results obtained show that the inorganic oxide network decreases the proton conductivity and water swelling. It is also found that increase in inorganic oxide content leads to decrease of methanol permeability. In terms of morphology, membranes are homogeneous and exhibit a good adhesion between inorganic domains and the polymer matrix. The properties of the composite membranes are compared with standard nafion membrane.

• Korean Chemical Engineering Research
• /
• v.49 no.5
• /
• pp.535-540
• /
• 2011

Organic-inorganic hybrid coating solutions were prepared starting from colloidal silica, lanthanum nitrate and ${\gamma}$-glycidoxypropyl trimethoxysilane by the sol-gel method. Also, spiropyran-doped hard coating solutions were prepared by mixing the spiropyran solution, obtained after dissolving spiropyran dye into tetrahydrofuran solvent, with the organic-inorgnic hybrid coating solutions. The spiropyran-doped hard coating solutions were applied as a thin layer to polycarbonate sheets, and their photochromic properties were investigated. The effect of amount of colloidal silica added into the coating solutions was investigated on the photochromic properties of coating films. Both decoloration rate and pencil hardness of the coating films were increased with increasing the amounts of colloidal silica.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.6 s.336
• /
• pp.17-22
• /
• 2005

Organic-inorganic hybrid type thin films are the next generation candidates as low-k materials. SiOC films are analyzed the bonding structure by the red and blue chemical shift using the fourier transform infraredspectra. Conventional chemical shift of organic chemistry is a red shift, but hybrid type SiOC films were observed the red and blue shift. The chemical shift originates from the interaction between the C-H bond and high electronegative atoms, and the blue shift in SiOC films is caused by the porosity due to the increase of the electron rich group such as much methyl radicals. The bonding structures of SiOC films are also divided into the Si-O-C cross-link structure and the Si-O-C cage-link structure due to the chemical shifts. The Si-O-C cross-link structure progressed the adhesion attributed to the C-H bond elongation in the reason of the red shift, and the dielectric constant also decreases.

• Polymer(Korea)
• /
• v.38 no.5
• /
• pp.573-579
• /
• 2014

The effect of synthesis conditions such as carbon nanotube (CNT), 2,2,2-trifluoroethylmethacrylate (3FMA), and composition of organic-inorganic material in ozone resistance and surface characteristics of ultraviolet cured organic-inorganic hybrid coating film has been investigated. Coating solution was prepared using tetraethoxysilane (TEOS), silane coupling agent methacryloyloxypropyltrimethoxysilane (MPTMS), 3FMA, various organic materials with acrylate group, and CNT, then bar-coated on substrates using applicator, and densified by UV-curing. It was found that ozone resistance and adhesion of the coating film were strongly dependent upon contents of TEOS, 3FMA, and CNT. Especially, ozone resistance, adhesion, and surface hardness of coating film with CNT were improved, relatively. Ozone resistance of coating film with a high TEOS content was increased, but adhesion was decreased. In addition, it was also found that ozone resistance of coating film was increased with contents of 3FMA. On the other hand, surface hardness was decreased with increase of 3FMA.

• Applied Chemistry for Engineering
• /
• v.22 no.6
• /
• pp.691-696
• /
• 2011

Organic-inorganic hybrid coating solutions were prepared by using a sol-gel method for transparent film. In this study, colloidal silica (CS) and alkoxy silane such as vinyltrimethoxysilane (VTMS), and [3-(methacryloyloxy)]propyltri methoxy silane (MAPTMS) were used in various conditions such as types of organic silane, weight ratios of CS to silane and reaction times. Coating solutions which were bar coated on the PET (polyethyleneterephthalate) film and cured were investigated on the chemical and physical properties. The pencil hardness and adhesion of coating films were increased with increasing the organic silane content in the coating solution compared to that of PMMA (polymethamethylcrylate) coating solution.

• Polymer(Korea)
• /
• v.36 no.5
• /
• pp.622-627
• /
• 2012

This study focuses on mechanical property enhancement and volatile organic compounds (VOCs) reduction characteristic of environmentally-friendly waterborne coatings. We synthesized a series of organic-inorganic hybrid waterborne polyurethanes by using poly(tetramethylene glycol) 2000, polycarbonate diol 2000, isophorone diisocyanate, dimethylolpropionic acid and titanium dioxide. The study on the effects of the R ratio([NCO]/[OH]) and inorganic contents on environmentally-friendly waterborne coatings showed that the R ratio with more than 1.5 is appropriate due to arrangement of hardsegments. The applied $TiO_2$ on films reduced volatile organic compounds (VOCs).