• 한국주조공학회지
• /
• 제31권4호
• /
• pp.212-217
• /
• 2011

The effects of alloying element and grain refinement on the tensile properties of magnesium alloy poured into sand mold were investigated. The strength of magnesium alloy was greatly increased by the addition of aluminium and that was increased with the increased aluminum content added up to 8.10 wt% and decreased beyond that. Even though the strength of Mg-8.10 wt%Al alloy was rather decreased by the addition of zinc, that was increased with increased zinc content added up to 0.50 wt% and decreased with the increased one beyond that. The maximum tensile strength was obtained with 0.50 wt%Mn added. The strength and elongation were simultaneously increased with grain refinement and the optimum amount of strontium addition for this was 0.30 wt%. The optimum chemical composition was obtained and the yield strength, tensile strength and elongation of the alloy with this composition were 90.2, 176.3MPa and 4.43%, respectively.

• 한국전기전자재료학회논문지
• /
• 제11권7호
• /
• pp.541-545
• /
• 1998

(PZT, PST, PT)/ YBCO structured have been grown on single crystal $LaAlO_3$ using in-situ Nb:YAG pulsed laser deposition technique. The optimum conditions of fabrication for high quality films have been established under various oxygen pressure. TBCO was used as a metallic electrode for polarizing ferroelectric thin fillms. Lattice mismatch of these materials were found to be with in 3%. As a result XRD patterns and rocking curves, (PZT, PST, PT)/ YBCO multiayered thin films on $LaAlO_3$ substrates showed preferred orientation to c-axis. For invastigation on electrical properties of ferroelectric thin films, remanent polaiztion $P_r$ and coercive field $E_c$ were measured for three samples. At each optimum condition, they showed the values of P_r=60 \mu C/cm^2 and E_c=240kV/ cm for PT, 30\mu C/cm^2 and 105kV/cm for PZT, 1.5\mu C/cm^2$ and 15kV/cm for PST. Frequency dependence of dielectric properties of ferroelectric thin fillms was also investigated. As a result, it showed the frequency dependence was relatively small in the range of 10Hz~10kHz.

• 한국세라믹학회지
• /
• 제32권5호
• /
• pp.535-542
• /
• 1995

The effect of sintering temperature, sintering time and forming pressure on microwave dielectric properties of (Zr1-xSnx)TiO4 ceramics containing 1.0wt% B2O3, 0.3 wt% La2O3 and 1.0wt% NiTa2O6 was investigated using the response surface methodology. The optimum values of processing variables were determined based on the reproducibility. The optimum values of the dielectric constant of >35. Q.f0 of >55000 and $\tau$f=$\pm$5 ppm/$^{\circ}C$ could be obtained when the sample was pressed at 500~600kg/$\textrm{cm}^2$ and sintered at 1500~155$0^{\circ}C$ for 2~3 hrs.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.321-324
• /
• 2005

The main purpose of the present study has been placed on investigating the effects of controlled rolling and cooling on the microstructures and mechanical properties of C-Si-Mn-V steels for cold forming. The steels were manufactured in vacuum induction melting(VIM) furnace and casted to 1.1ton Ingots and the ingots were forged to $\Box150$ billet. The forged billets were reheated in walking beam furnace and rolled to coil, the stocks were rolled by Controlled Rolling and Cooling Technology (CRCT), so rolled at low temperature by water spraying applied in rolling stage and acceleratly cooled before coiling. Rolled coils were cold drawed to the degree of $27\%$ of area reduction without heat treatment. Microstructual observation, tensile test, compression test and charpy impact tests were conducted. The mechanical properties of the steels were changed by area reduction of cold drawing and it is founded that there are optimum level of cold drawing to minimize compression stress for these steels. From the result of this study, it is conformed that mechanical properties and microstructure of C-Si-Mn-V steels for cold forming were enhanced by accelerated cooling and founded optimum level of cold drawing.

• Journal of Korean Vacuum Science & Technology
• /
• 제2권2호
• /
• pp.78-84
• /
• 1998

ZnO:Al films were prepared by an rf magnetron sputtering and targets for the experiments were fabricated by sintering the mixture of ZnO and Al2O3. The most conductive film was obtained from the target with 2.0∼2.2 wt.% of Al2O3. Optical properties studied with spectroscopic ellipsometry showed band gap widening, i.e., the Burstein-Moss shift, with aluminum doping as well as with the elevation of deposition temperature. And it is found that the optical and electrical properties were related to the density of states as well as the variation of donor level. when hydrogen atoms were introduced into the films, the activation energy for the generation of oxygen vacancy was smaller for the films showing higher conductivity. This indicates that the optimum deposition condition for highly conductive ZnO:Al film has strong relation to the optimum doping condition.

• 대한금속재료학회지
• /
• 제50권4호
• /
• pp.263-270
• /
• 2012

This study investigates the effect of heat treatment on the mechanical properties of a forged Ni-based superalloy called Nimonic 80A. Nimonic 80A ingot samples were fabricated by vacuum spray casting to achieve a fine and homogenized microstructure. The ingot samples were subsequently hot-forged with the diameter of 220 mm at 1373 K. From the center to the surface of the forged Nimonic 80A, its average grain size decreased and its micro-Vickers hardness increased slightly. Solution treatment was carried out at 1353 K with 8 hours of air cooling followed by aging treatment, which was carried out in the range of 873-1073 K with various times from 0.5 to 256 hours. To set the optimum aging conditions, micro-Vickers hardness tests were performed. The maximum hardness value of 388.0 Hv was obtained by aging at 973 K for 32 hours. Also, tensile tests were performed for optimum aging conditions at room temperature and 873 K. The results can be used effectively to perform reasonable heat treatment of Nimonic 80A superalloy.

• 한국조리학회지
• /
• 제7권3호
• /
• pp.179-191
• /
• 2001

밀가루전립분 혼입이 빵생지의 물성 및 yeast(S.cerevisiae)의 가스발생력에 미치는 영향을 검토한 실험은 밀전립분의 혼입비율 0, 25, 50, 75, 100%의 5군으로 구성 해 그 제빵성에 대해서 검토하였다. 1) 패리노그래프에 의해 흡수율을 측정한 결과 밀전립분은 빵용 밀가루에 비해 1.3배의 흡수율을 나타냈다. 2) Texture meter에 의한 dough 정도는 수분일정 생지의 경우는 혼입비율의 증가와 함께 딱딱하게 되고 응집성은 감소하였다. 흡수율에 의해 산출한 최적수분량은 조정한 경우의 dough의 점도 및 응집성은 제빵용 밀가루와 거의 같았다. 3) 밀전립분은 S.cerevisiae의 가스발생력에 좋은 영향을 주지 않고 수분일정생지의 경우 전체 가스 발생량 및 내포잔류 가스량과 혼입비율에서도 거의 비슷한 결과를 얻었다. 그리고 수분조정반죽의 경우는 밀전립분 혼입비율의 증가와 함께 전체 가스발생량 및 내포한 잔류 가스량의 증가가 확인되었다. 4) 빵의 품질평가의 결과 밀전립분을 25-50%혼입하여 수분 조정한 것이 가장 좋은 것으로 확인되었다.

• 마이크로전자및패키징학회지
• /
• 제10권2호
• /
• pp.55-59
• /
• 2003

본 연구에서는 RF-Magnetron 스퍼터링 장치를 이용하여 $Al_xTa_{1-x}$(x=0.0∼1.0) 합금박막을 성장하였고, 4탐침법, XRD, AFM, micro-Vickers 미소경도계를 사용하여 시료의 구조적, 기계적, 전기적 특성을 분석하였다. Al조성 x=0.245(Al 24.5 at.%)에서 전기저항이 가장 높게 나타났고, 결정질이 가장 우수하였다. 표면 hillock에 있어서는 낮은 Al 조성영 역에서는 x가 증가할수록 hillock이 감소하다가, x=0.245에서 hillock이 완전히 배제되었고, 이후 x 증가에 따라 hillock 밀도가 다시 급격히 증가하였다. 미소경도의 경우, Al조성 x=0.2∼0.45의 영역에서 가장 높은 경도값이 측정되었다. 본 연구의 모든 결과를 종합적으로 고려할 때, $Al_xTa_{1-x}$ 합금박막의 결정질, 전기저항, 표면형상, 미소경도는 상호 밀접한 관계를 가지고 있었으며, Al 조성 x=0.245에서 가장 우수한 물리적 특성이 나타났다.

• 한국재료학회지
• /
• 제17권2호
• /
• pp.68-72
• /
• 2007

Optimum compositions for piezoelectric properties of $(Bi_{0.5}Na_{0.5})_{(1-x)}Ba_xTiO_3$ ceramics were investigated in the range of $x=0{\sim}0.1$ covering rhombohedral to tetragonal phase regions. No impurity phases other than a perovskite phase were found and the grain size decreased with increasing x. A two-phase coexisting morphotropic phase area rather than boundary dividing rhombohedral and tetragonal phase regions appeared to exist at $x=0.05{\sim}0.08$. As for piezoelectric properties within morphotropic phase compositions, the piezoelectric constant ($d_{33}$) and the electromechanical coupling factor ($K_p$) showed peak values at x=0.065, 192 pC/N and 34%, respectively, indicating x=0.065 as an optimum composition for piezoelectric $(Bi_{0.5}Na_{0.5})_{(1-x)}Ba_xTiO_3$ ceramics.

• 분석과학
• /
• 제8권3호
• /
• pp.341-350
• /
• 1995

Melt-spinning법을 이용하여 $Nd_{14}Fe_{80}B_6$ 조성의 리본합금을 제조하고 각 제조조건별 시편에 대한 자기적 특성을 분석하였다. 리본합금의 미세구조와 자기적 특성은 냉각속도 및 열처리 조건에 민감하게 변화하였다. As-quenched 상태의 경우 wheel 속도 20m/sec에서 가장 좋은 자기적 특성을 나타내었으며, 비정질 상태의 리본시편에 대한 열처리 효과는 22m/sec에서 제조된 리본시편을 $600^{\circ}C$에서 30분간 진공열처리하였을 때 가장 좋은 결과를 얻을 수 있었다. 또한 $Nd_2Fe_{14}B$상의 결정화 온도는 DTA 분석결과 $595^{\circ}C$ 부근이었다.