• Journal of Korea Foundry Society
• /
• 제31권4호
• /
• pp.212-217
• /
• 2011

The effects of alloying element and grain refinement on the tensile properties of magnesium alloy poured into sand mold were investigated. The strength of magnesium alloy was greatly increased by the addition of aluminium and that was increased with the increased aluminum content added up to 8.10 wt% and decreased beyond that. Even though the strength of Mg-8.10 wt%Al alloy was rather decreased by the addition of zinc, that was increased with increased zinc content added up to 0.50 wt% and decreased with the increased one beyond that. The maximum tensile strength was obtained with 0.50 wt%Mn added. The strength and elongation were simultaneously increased with grain refinement and the optimum amount of strontium addition for this was 0.30 wt%. The optimum chemical composition was obtained and the yield strength, tensile strength and elongation of the alloy with this composition were 90.2, 176.3MPa and 4.43%, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• 제11권7호
• /
• pp.541-545
• /
• 1998

(PZT, PST, PT)/ YBCO structured have been grown on single crystal $LaAlO_3$ using in-situ Nb:YAG pulsed laser deposition technique. The optimum conditions of fabrication for high quality films have been established under various oxygen pressure. TBCO was used as a metallic electrode for polarizing ferroelectric thin fillms. Lattice mismatch of these materials were found to be with in 3%. As a result XRD patterns and rocking curves, (PZT, PST, PT)/ YBCO multiayered thin films on $LaAlO_3$ substrates showed preferred orientation to c-axis. For invastigation on electrical properties of ferroelectric thin films, remanent polaiztion $P_r$ and coercive field $E_c$ were measured for three samples. At each optimum condition, they showed the values of P_r=60 \mu C/cm^2 and E_c=240kV/ cm for PT, 30\mu C/cm^2 and 105kV/cm for PZT, 1.5\mu C/cm^2$ and 15kV/cm for PST. Frequency dependence of dielectric properties of ferroelectric thin fillms was also investigated. As a result, it showed the frequency dependence was relatively small in the range of 10Hz~10kHz.

• Journal of the Korean Ceramic Society
• /
• 제32권5호
• /
• pp.535-542
• /
• 1995

The effect of sintering temperature, sintering time and forming pressure on microwave dielectric properties of (Zr1-xSnx)TiO4 ceramics containing 1.0wt% B2O3, 0.3 wt% La2O3 and 1.0wt% NiTa2O6 was investigated using the response surface methodology. The optimum values of processing variables were determined based on the reproducibility. The optimum values of the dielectric constant of >35. Q.f0 of >55000 and $\tau$f=$\pm$5 ppm/$^{\circ}C$ could be obtained when the sample was pressed at 500~600kg/$\textrm{cm}^2$ and sintered at 1500~155$0^{\circ}C$ for 2~3 hrs.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.321-324
• /
• 2005

The main purpose of the present study has been placed on investigating the effects of controlled rolling and cooling on the microstructures and mechanical properties of C-Si-Mn-V steels for cold forming. The steels were manufactured in vacuum induction melting(VIM) furnace and casted to 1.1ton Ingots and the ingots were forged to $\Box150$ billet. The forged billets were reheated in walking beam furnace and rolled to coil, the stocks were rolled by Controlled Rolling and Cooling Technology (CRCT), so rolled at low temperature by water spraying applied in rolling stage and acceleratly cooled before coiling. Rolled coils were cold drawed to the degree of $27\%$ of area reduction without heat treatment. Microstructual observation, tensile test, compression test and charpy impact tests were conducted. The mechanical properties of the steels were changed by area reduction of cold drawing and it is founded that there are optimum level of cold drawing to minimize compression stress for these steels. From the result of this study, it is conformed that mechanical properties and microstructure of C-Si-Mn-V steels for cold forming were enhanced by accelerated cooling and founded optimum level of cold drawing.

• Journal of Korean Vacuum Science & Technology
• /
• 제2권2호
• /
• pp.78-84
• /
• 1998

ZnO:Al films were prepared by an rf magnetron sputtering and targets for the experiments were fabricated by sintering the mixture of ZnO and Al2O3. The most conductive film was obtained from the target with 2.0∼2.2 wt.% of Al2O3. Optical properties studied with spectroscopic ellipsometry showed band gap widening, i.e., the Burstein-Moss shift, with aluminum doping as well as with the elevation of deposition temperature. And it is found that the optical and electrical properties were related to the density of states as well as the variation of donor level. when hydrogen atoms were introduced into the films, the activation energy for the generation of oxygen vacancy was smaller for the films showing higher conductivity. This indicates that the optimum deposition condition for highly conductive ZnO:Al film has strong relation to the optimum doping condition.

• Korean Journal of Metals and Materials
• /
• 제50권4호
• /
• pp.263-270
• /
• 2012

This study investigates the effect of heat treatment on the mechanical properties of a forged Ni-based superalloy called Nimonic 80A. Nimonic 80A ingot samples were fabricated by vacuum spray casting to achieve a fine and homogenized microstructure. The ingot samples were subsequently hot-forged with the diameter of 220 mm at 1373 K. From the center to the surface of the forged Nimonic 80A, its average grain size decreased and its micro-Vickers hardness increased slightly. Solution treatment was carried out at 1353 K with 8 hours of air cooling followed by aging treatment, which was carried out in the range of 873-1073 K with various times from 0.5 to 256 hours. To set the optimum aging conditions, micro-Vickers hardness tests were performed. The maximum hardness value of 388.0 Hv was obtained by aging at 973 K for 32 hours. Also, tensile tests were performed for optimum aging conditions at room temperature and 873 K. The results can be used effectively to perform reasonable heat treatment of Nimonic 80A superalloy.

• Culinary science and hospitality research
• /
• 제7권3호
• /
• pp.179-191
• /
• 2001

The effects of whole wheat flour on the Rheological Properties of dough gassing power of yeast S.cerevisiae and breadmaking properties were studied. The blending ratios of whole wheat flour to bread making flour were 0, 25, 50, 75 and water absorption in the farinography increasedlinerly from 62.5%in 100% bread making flour and 77.5% in 100% whole wheat flour. The hardness and cohesiveness of dough prepared with optimum moisture content was constant regardless of the blending ratio of whole wheat flour. whole wheat flour had no effect on the total gas production or the internal gas content in the dough at a constant moisture level but had detrimental effect on the loaf volume. In a dough at the optimum moisture level, whole wheat flour increased the two former parameters sensory evaluation indicated that the replacement in the range of 25 to 50% with whole wheat flour at the optimum moisture level was acceptable

• Journal of the Microelectronics and Packaging Society
• /
• 제10권2호
• /
• pp.55-59
• /
• 2003

In this study, $Al_xTa_{1-x}$(x=0.0∼1.0) alloy thin films were grown by RF-Magnetron sputtering system, and the structural, mechanical and electrical properties of samples were examined by 4-point probe, XRD, AFM and micro-Vickers hardness profiler. The electrical resistivity was maximum and the crystal quality was optimum for the samples with Al content x=0.245 (Al 24.5 at.%). Regarding the surface hillock formation, the hillock density decreased with an increase of Al content for the low Al content range, and the hillock was eliminated for the sample with Al=24.5 at.%. The hillock density increased with the further increase of Al content. The high values of micro-Vickers hardness were obtained for the samples with x=0.2∼0.45. The results obtained demonstrate that the crystal quality, electrical resistivity, surface morphology and micro-hardness are closely inter-related, and that the optimum physical properties are obtained for the sample with x=0.245.

• Korean Journal of Materials Research
• /
• 제17권2호
• /
• pp.68-72
• /
• 2007

Optimum compositions for piezoelectric properties of $(Bi_{0.5}Na_{0.5})_{(1-x)}Ba_xTiO_3$ ceramics were investigated in the range of $x=0{\sim}0.1$ covering rhombohedral to tetragonal phase regions. No impurity phases other than a perovskite phase were found and the grain size decreased with increasing x. A two-phase coexisting morphotropic phase area rather than boundary dividing rhombohedral and tetragonal phase regions appeared to exist at $x=0.05{\sim}0.08$. As for piezoelectric properties within morphotropic phase compositions, the piezoelectric constant ($d_{33}$) and the electromechanical coupling factor ($K_p$) showed peak values at x=0.065, 192 pC/N and 34%, respectively, indicating x=0.065 as an optimum composition for piezoelectric $(Bi_{0.5}Na_{0.5})_{(1-x)}Ba_xTiO_3$ ceramics.

• Analytical Science and Technology
• /
• 제8권3호
• /
• pp.341-350
• /
• 1995

$Nd_{14}Fe_{80}B_6$ ribbon alloy was manufactured with using melt-spinning method and analyzed the magnetic properties according to the manufacturing conditions. The microstructure and magnetic properties of melt-spun ribbons are sensitively dependent on the quench rate and annealing conditions. As-quenched $Nd_{14}Fe_{80}B_6$ ribbons with optimum magnetic properties are obtained at wheel speed($v_s$) of about 20m/sec and over quenched ribbons show optimum magnetic properties at $v_s$=22m/see when annealed for 30 minutes at $600^{\circ}C$ under vacuum. The crystallization temperature($T_k$) of $Nd_2Fe_{14}B$ phase is about $595^{\circ}C$ in the DTA analysis.