• 한국의류학회지
• /
• 제29권7호
• /
• pp.997-1007
• /
• 2005

The textile finishing methods utilizing chitosan have been mostly focused on the applications in the improvement of the dyeing of cotton fabrics, or the improvement of hand of the cotton or wool fabrics. On the other hand, it Is difficult to find the application examples in the synthetic fiber fabrics including polyester and nylon fabrics. The aim of this study is to improve the stiffness and the poor wash fastness of the fabrics treated only with chitosan. We tried to improve the softness by employing chitosan and polyurethane mixture solution and to prevent the detachment of the chitosan from the fabric. The treatment was applied to cotton, polyester, and nylon fabrics. The change of the properties of the treated fabrics were investigated. The optimum finishing condition was sought by changing the mixture ratio of the chitosan/PU(polyurethane) solutions. The adjusted ratios of the chitosan/PU solutions were 1 : 0, 1 : 0.25, 1 : 0.5, and 1 : 2 during the mixture solution preparation. Using the KES(Kawabata Evaluation System), the physical and mechanical properties of the finished fabric specimens were analyzed, and hand values of the specimens were calculated through the use of translational formulas. According to the chemical composition of the fibers, chitosan solution or chitosan/PU mixture exhibited wide range of coating effect. Since the chitosan acid solution has high polarity, the bonding force with the cotton fibers is high. By the appropriate addition of PU in the chitosan treatment of cotton, KOSHI and HARI values of the fabric improved. The air permeability of the chitosan/PU treated cotton fabric specimen improved, resulting in the highest value at the mixture of chitosan : PU=1:0.25.

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제6권4호
• /
• pp.61-72
• /
• 2001

폐기물 매립장에는 발생되는 침출수의 유출을 방지하기 위하여 매립장의 바닥 또는 측면에 투수계수가 1x$10^{7}$cm/sec이하인 차수재를 설치한다. 본 연구는 폐기물 매립장 차수재인 토양-벤토나이트 차수재 (혼합토)를 대상으로 하여 현장토의 토성에 따른 벤토나이트의 배합비와 투수계수의 특성을 파악하고 벤토나이트의 팽윤도 및 다짐방법이 차수층의 투수특성에 미치는 영향을 파악하였다. 연구결과 동일조건에서 최대건조밀도는 SC계열의 혼합토가 CL계열의 혼합토보다 높게 나타났고, 최적함수비는 그 반대의 경향을 나타냈으며, 다짐방법별로는 최대건조밀도의 경우 D다짐시가 높게 나타났고, 최적함수비는 A다짐시의 경우가 높게 나타났다. 다짐에너지에 따른 최대건조밀도의 차이는 SC계열의 혼합토가 더 큰 것으로 나타났고, 최적함수비의 경우는 CL계열의 혼합토가 더 큰 차이를 보이는 것으로 나타났으며 팽윤도에 따른 최대건조밀도 및 최적함수비의 차이는 미미하였다. 벤토나이트의 배합비 및 팽윤도가 증가함에 따라 투수계수는 낮은 값을 나타내었고 동일조건에서는 CL계열의 혼합토와 D다짐시 낮은 투수계수를 나타내었다. 그러나 투수계수는 팽윤도보다는 벤토나이트의 배합량에 의해 더 많은 영향을 받는 것으로 나타났고 동일조건에서 SC계열의 혼합토와 A다짐시 더 큰 차이를 나타내었다. 투수시험결과에 따른 시공시 경제성을 검토한 결과 팽윤도가 낮은 벤토나이트를 배합한 경우가 더 경제적인 것으로 나타났는데 이는 팽윤도별 재료단가의 큰 차이에 비해 투수계수 감소효과가 기대에 미치지 못하기 때문인 것으로 판단된다.

• 한국건축시공학회지
• /
• 제6권1호
• /
• pp.101-107
• /
• 2006

While a Study with regard to the measurement on Concrete Strength and the Change of Drying Shrinkage in accordace with Content Ratio of Crushed Stone Powder, it is being analyzed as the result that the strength according to Content Ratio of crushed Stone Powder is somewhat lowering. Accordingly, it is the real situation that the Concrete mixed with Crushed Stone Powder is utilized for non-structural material, not for the structural material. Therefore, this Research willing to furnish the suitable utilizing scheme for construction site as well as practical life by means of conduct the experiment on both Concrete Pressure Strength according to mixture with Crushed Stone Powder and Elastic Modulus, it also presumes the optimum Elastic Modulus Equation after analysis of comparison with common concrete strength. As the result of the experiment, in case of the Content Ratio of Crushed Stone Powder is less than 5%, it did not display a big difference in its both strength and matter-property compare with common concrete. In case of Elastic Modulus, when the Pressure Strength is 50% and 40% respectively, the Elastic Modulus Equation accords very well with the provided condition of Quadratic function, and as the result of the Presumption on Elastic Modulus according to Content of Crushed Stone Powder, in case the Pressure Strength is 50%, Elastic Modulus Equation showed that Error Ratio of Cubic function is at degree of 0.0005%, in case the Pressure Strength is 40%, Elastic Modulus Equation was accorded well with the value of the experimental data likely as the Error Ratio of Cubic function is at the degree around 0.0034%, respectively.

• 한국식품영양과학회지
• /
• 제37권4호
• /
• pp.505-511
• /
• 2008

고추장, 고춧가루, 과채열수추출액 첨가에 의한 돼지불고 기양념육의 항산화 증진 효과와 혼합물 실험설계법을 이용한 돼지불고기용 양념소스 재료의 최적 혼합 비율을 확립하고자 하였다. 냉동저장($-25^{\circ}C$, 5개월) 동안 간장양념을 사용한 대조구와 고추장양념첨가구(KG), 고추장양념.과채열수 추출액첨가구(KFVEG)의 TBA가는 저장기간 동안 원료육에 비해 모든 돼지불고기 양념육에서 낮게 유지되었다. 양념육 중에서는 대조구보다 고추장양념첨가구의 항산화력이 크게 우수하였으며, 고추장양념첨가구의 물 사용량을 과채 열수추출액으로 대체함으로써 항산화 상승작용이 유의적으로 나타났다. 따라서 양념소스에 고추장, 고춧가루, 과채열 수추출액 첨가로 돼지불고기양념육의 지방산화 안정성이 증진되었다. 양념육의 기호성은 고추장과 함께 사용된 고춧가루와 과채열수추출액 사용 비율이 증가함에 따라 향상되는 것으로 나타났다. 혼합물 실험 설계법에 의하여 추적된 돼지불고기용 고추장양념소스의 최적 혼합 비율은 고추장 0.04, 고춧가루 0.20, 과채열수추출액 0.39, 물 0.37로 나타났다.

• 대한기계학회논문집B
• /
• 제20권7호
• /
• pp.2421-2429
• /
• 1996

The objective of this research is to apply effect of the pre-mixed combustion quantity and smoke emission in diesel engine. According as air fuel ratio is increased, emission of smoke concentration is linearly reduced. As Injection timing is advanced, smoke concentration is remarkably reduced. It is considered to be the primary cause of the increase in the premixed combustible mixture during long ignition delay period with advancing injection timing. Smoke is increased with increasing engine speed, so it is considered to be the primary cause of the increase of the mass of fuel injected. Smoke is decreased according to the increase of methanol volume ratio. It is considered that the primary cause of the increase in the quantity of pre-mixed combustion.

• 한국환경보건학회지
• /
• 제27권4호
• /
• pp.79-83
• /
• 2001

The sludge wastes fermentation process reactors were operated to produce the VFAs(volatile fatty acids) as supplemental carbon sources and to determine the optimum operating conditions. The experiment was carried out by varied mixture ration of 400:0 350:30 300:100 200:200 and operating temperature 2$0^{\circ}C$ 3$0^{\circ}C$ and 4$0^{\circ}C$ The results were as follows: Higher VFAs production rate observed at higher mixed ratio of primary sludge. When the mixed ratio of primary sludge and return sludge were 400:0 350:50 300:100 200:200 respectively. VFAs production are were 829.6mg/l 944.2 mg/l 597.9mg/ml an d441.6 mg/l , respectively. the yield of VFAs increased with temperature, but decreased with initial TSS concentration Because fermented sludge has relatively low nitrogen and phosphorus and relatively high VFAs it can be used as a substitute for external carbon in biological nutrient removal process.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 The 6th International Symposium of East Asian Resources Recycling Technology
• /
• pp.117-121
• /
• 2001

The present study has been conflicted to verify the applicability of tire powder and food waste compost as biofilter materials to degrade volatile organic compounds. Batch and column tests were performed to determine the optimum ratio of tire powder to compost and the appropriate mixing type of two materials for removal of the selected VOCs, i.e., benzene, ethylbenzene, PCE, and TCE. According to batch tests, tire powder and compost mixture had faster removal rate than the compost. The biofilter column filled with tire powder and compost showed better VOC removal efficiency than that filled with only tire powder. In this study, the best removal rate was observed in the sandwich type column test of which the tire : compost weight ratio was 1:2

• 한국환경과학회지
• /
• 제19권6호
• /
• pp.681-687
• /
• 2010

Mesoporous silica was prepared from hydrothermal synthesis using gel mixture of tetraethylorthosilcate (TEOS) as silica source and cetyltrimethylammonium bromide (CTMABr) as a surfactant. In the optimum synthesis cause, molar ratio of template and silica changed. The surface and structure properties of mesoporous silica were determined by XRD, SEM, TEM and BET. Also, surface potential of mesoporous silica was measured using zeta potential. $N_2$ adsorption isotherm characteristics, including the specific surface area ($S_{BET}$), total pore volume $V_T$), and average pore diameter ($D_{BJH}$), were determined by BET. As a result, SBET of $100m^2/g{\sim}1500m^2/g$ was determined from the $N_2$ adsorption isotherm. Also, the average pore diameter was 2 nm∼4 nm. Mesoporous silica's surface potential of minus charge was determined from zeta potential.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.328-331
• /
• 2000

Carbon nanotube(CNT) was successfully grown on Ni-W alloyed substrate by applying PECVD technique(Plasma Enhanced Chemical Vapor Deposition). As a catalyst, Ni-W alloyed substrate was prepared by mechanical alloying method. In order to find the optimum growth condition, initially two different types of gas mixtures such ac $C_2$H$_2$-H$_2$and $C_2$H$_2$-MH$_3$were systematically investigated by adjusting results on the mixing ratio in temperature range of 500 to 80$0^{\circ}C$. In this work, we will report the preliminary results on the CNT processed by PECVD, which were characterized by XRD, SEM and TEM. Finally we will evalute the effect on CNT growth by changing many processing parameters, such as typical gas, mixing ratio between 2 mixture, plasma power and etc.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1996년도 추계학술발표회논문집(2)
• /
• pp.506-511
• /
• 1996

Research on the dry etching of UO$_2$ by using fluorine containing gas plasma is carried out for DUPIC (Direct Use of spent PWR fuel In CANDU) process which is taken into consideration for potential future fuel cycle in Korea. CF$_4$/O$_2$ gas mixture is chosen for the reactant gas and the etching rates of UO$_2$ by the gas plasma are investigated as functions of substrate temperature, plasma gas pressure, CF$_4$/O$_2$ ratio, and plasma power, It is tentatively found that the etching rate can reach 1000 monolayers/min. and the optimum CF$_4$/O$_2$ ratio is around 4:1.