• Journal of Korea Water Resources Association
• /
• v.36 no.1
• /
• pp.61-74
• /
• 2003

This study(II) apply to the A city by using the optimal rehabilitation model based on the deterioration prediction of the water distribution system proposed the study(I). The deterioration prediction model divides factors into 14 factors with digging and experiment and 9 factor without digging and experiment and calculate the deterioration degree. The application results of the deterioration prediction model show that a difference of the deterioration degree according to factor numbers is within 1~2%. Also, the model can predict the deterioration degree of each pipe without digging and experiment. The optimal rehabilitation model is divided into the optimal residual durability of each deterioration factor and budget constraint or not. The application result is as follow: the rehabilitation time and cost increase according to the increasing of the optimal residual durability. When compared the model with budget constraint and model without budget constraint, the former model increase the cost of total contents. In case of budget constraint, the increasing tendency is concluded that the pipe rehabilitation is executed in same budget every year in condition that every rehabilitation cost do not exceed the every year budget within the optimal residual durability.

• Journal of Korea Water Resources Association
• /
• v.36 no.1
• /
• pp.45-59
• /
• 2003

The method in this study, which is more efficiency than the existing method, propose the optimal rehabilitation model based on the deterioration prediction of the laying pipe by using the deterioration survey method of the water distribution system. The deterioration prediction model divides the deterioration degree of each pipe into 5 degree by using the probabilistic neural network. Also, the optimal residual durability is estimated by the calculated deterioration degree in each pipe and pipe diameter. The optimal rehabilitation model by integer programming base on the shortest path can calculate a time and cost of maintenance, rehabilitation, and replacement. Also, the model is divided into budget constraint and no budget constraint. Consequently, the model proposed by the study can be utilized as the quantitative method for the management of the water distribution system.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.2
• /
• pp.137-143
• /
• 2000

An automobile clutch diaphragm spring is operating in a closed clutch housing under high temperature and subject to high stress concentration in driving condition, which frequently causes cracks and fracture. The material of spring is required to possess sufficient fatigue strength and tenacity, which depend largely on the condition of tempering heat treatment. In this paper, specimens are made under a number of different tempering temperatures md tested to find the optimal tempering heat treatment condition. The experiments include the verification of microscopic structure, hardness, tensile strength, fatigue crack growth rate, stress intensity factor range and residual stress. Also, decarbonization, which occurs in actual heat treatment process, is measured and allowable decarbonization depth is studied by durability test.

• Journal of the Korean Wood Science and Technology
• /
• v.32 no.4
• /
• pp.46-51
• /
• 2004

The objective of this study was to evaluate the applicability of high temperature drying to pitch pine (Pinus rigida) lumber, especially intended for use as lamina of structural glued laminated timber (glulam), to enhance the efficient utilization and provide added-value to that species. The high temperature schedule and drying procedures utilized were shown to be reasonable for drying glulam lamina due to the occurrence of small moisture gradients, minimal residual drying stress, and low warpage. Through preliminary tests, it was confirmed that residual resin at lamina surfaces did not adversely affect the gluing process. However, quantitative analysis of resin is required for developing a method to constrain the occurrence of pitch trouble with respect to decreasing long-term adhesive and finish durability of glulam in use after manufacturing. The final moisture content of high temperature dried lamina was much lower than target moisture content and discoloration was more severe than anticipated. In a further study, it will be necessary to determine the optimal drying conditions, such as temperature, humidity, drying time, and top load restraint level, which could best control discoloration, warpage, and moisture content of the lamina, while minimizing fuel expense.

• Journal of the Korean Geosynthetics Society
• /
• v.22 no.4
• /
• pp.17-26
• /
• 2023

To consider the risk of damage and fracture of P.C strands, the existing post-maintenance system alone has the limitations, hence it is necessary to quantitatively evaluate and predict the deterioration, durability and safety of facilities and establish a reasonable maintenance system considering the asset value of facilities. Therefore, it is worth considering a preventive maintenance plan that allows proactive measures to be taken before a major defect occurs in the temporary anchor. This study devised a preventive over tension method, reviewed its effectiveness through design and field tests, by calculating the resistance factors by performing a reliability-based optimization design. At this time, the over tension anchor method was evaluated using the ratio of the residual tension force after the fracture of P.C strands to the effective tension force before the fracture of P.C strand, followed by the resistance factor calculated by the optimal solution for each random variables using Excel solver and applying it to the limit state equations. As a result of the study, if the over tension ratio is 125% to 130%, the remaining strands showed a high resistance effect even after the fracture of P.C strand. As a result of the optimization design, it was found that it is appropriate to apply the load factor (γ) of 1.25, and the resistance factors of Φ₁, Φ₂, Φ₃ as 0.7, 0.5, 0.6.