• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1993.10a
• /
• pp.761-767
• /
• 1993

A precision planting system using computer controlled technology for mulching cultivation was developed and tested . The system consisting of a micro-computer, several optical fiber sensors and control actuators realized the mechanization of the precision planting operation. The film hole positions, existences of a seed on shutter were detected and the planting speed was measured. The shutter opening mechanism and a seed metering device driven by a stepping motor were controlled, automatically . The planting timing of the shutter opening mechanism were analyzed from a video camera motion analysis, theoretically. The results showed a sufficient accuracy of a seed planted into the center a film hole with a variety of planting speeded. The gravity point positions in film hole of seeds planted by the system just were within the area of +-5mm of the hole center when the hole diameter was 40mm.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.8
• /
• pp.843-850
• /
• 2016

This paper introduces a novel modulation scheme for vehicular communication in taking advantage of existing LED lights available on a car. Our proposed 2-Phase Shift Keying (2-PSK) is a spatial modulation approach in which a pair of LED light sources in a car (either rear LEDs or front LEDs) is used as a transmitter. A typical camera (i.e. low frame rate at no greater than 30fps) that either a global shutter camera or a rolling shutter camera can be used as a receiver. The modulation scheme is a part of our Image Sensor Communication proposal submitted to IEEE 802.15.7r1 (TG7r1) recently. Also, a neural network approach is applied to improve the performance of LEDs detection and decoding under the noisy situation. Later, some analysis and experiment results are presented to indicate the performance of our system

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.34 no.10
• /
• pp.399-406
• /
• 1985

In this paper transparent PLZT ceramics for the composition of 9/65/35 (La/Zr/Ti ) are fabricated using hotpress and the possibility of application to optical shutter is examined by obtaining the On-Off characteristics of specimens. The ferroelectric E-P hysteresis loop exhibits slim loop suitable for the quadratic electrooptic effect. Measurements of the electrooptic effect show that specimens have the quadratic electrooptic effect but the light intensities as functions of electric field exhibit butterfly type hysteresis curves because of its slightly large saturation remanent polarization and coercive field. On-Off characteristics are obtained by electric fields of-6 kv/cm and +2kv/cm. As a result of experiments, 9/65/35 PLZT ceramics can be applied to optical shutter but construction with other composition which has more slim hysteresis loop is desired for obtaining the Off state by zero electric field.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.10a
• /
• pp.763-764
• /
• 2013

A three-dimensional image capturing device and its signal processing algorithm and apparatus are presented. Three dimensional information is one of emerging differentiators that provides consumers with more realistic and immersive experiences in user interface, game, 3D-virtual reality, and 3D display. It has the depth information of a scene together with conventional color image so that full-information of real life that human eyes experience can be captured, recorded and reproduced. 20 Mega-Hertz-switching high speed image shutter device for 3D image capturing and its application to system prototype are presented[1,2]. For 3D image capturing, the system utilizes Time-of-Flight (TOF) principle by means of 20MHz high-speed micro-optical image modulator, so called 'optical resonator'. The high speed image modulation is obtained using the electro-optic operation of the multi-layer stacked structure having diffractive mirrors and optical resonance cavity which maximizes the magnitude of optical modulation[3,4]. The optical resonator is specially designed and fabricated realizing low resistance-capacitance cell structures having small RC-time constant. The optical shutter is positioned in front of a standard high resolution CMOS image sensor and modulates the IR image reflected from the object to capture a depth image (Figure 1). Suggested novel optical resonator enables capturing of a full HD depth image with depth accuracy of mm-scale, which is the largest depth image resolution among the-state-of-the-arts, which have been limited up to VGA. The 3D camera prototype realizes color/depth concurrent sensing optical architecture to capture 14Mp color and full HD depth images, simultaneously (Figure 2,3). The resulting high definition color/depth image and its capturing device have crucial impact on 3D business eco-system in IT industry especially as 3D image sensing means in the fields of 3D camera, gesture recognition, user interface, and 3D display. This paper presents MEMS-based optical resonator design, fabrication, 3D camera system prototype and signal processing algorithms.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.519-521
• /
• 2005

The electrooptical characteristics of OMI (optical mode interference) cell were investigated as the application for LC shutters. The optical responses under dynamic driving were simulated by solving the Ericksen-Leslie hydrodynamic equations numerically. The prototypes were made accordingly for verification. The experimental data show good coincidence with the simulation results.

• Korean Journal of Optics and Photonics
• /
• v.9 no.6
• /
• pp.368-372
• /
• 1998

A 16-views 3 dimensional imaging system is designed by spatially combinding two 8-views time multiplexed image channels. Each 8-views channel composed of 3 primary color CRTs and a dichroic beam splitter which combining the three CRTs as one channel. Each CRT displays 8-view images time sequentially. These images are projected to a holographic screen of a size 1$\times$0.8 $m^2$ through a projection optics. Characteristics of the three different configurations of projection optics are examined with the optics designing program "DEMOS" to select an optimized projection optics for the system. The configulation of the optimized projection optics is found like following; images from each channel combined by two-fold mirror are projected by a projection objective through a 16-strips LCD shutter. In this configuration, the shutter should be located at the entrance pupil of the objective, and the folded edge of the two-fold mirror should contact symmetrically to the center line of the shutter.e shutter.

• Journal of KIEE
• /
• v.10 no.1
• /
• pp.1-6
• /
• 2000

This paper represents the design of 3D endoscopic video system in order to improve visualization and enhance the ability of the surgeon to perform delicate endoscopic surgery. In comparison of the polarized and electric shutter-type stereo imaging system, The former is superior in terms of accuracy and performance speed for knot-tying and loop pass test. The result of experiments show that the proposed 3D endoscopy system has a wide viewing angle and zone which is necessary for multi-view and it has better image quality and stability of the optical performances than the electric shutter-type does.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.12 s.189
• /
• pp.117-121
• /
• 2006

Generally, micro-stereolithography technology uses laser and complex optical system as light source and light delivery system, respectively. In this research, a novel micro-stereolithography technology that uses UV lamp that is more economical than UV laser as light source and optical fiber that is simpler than previous light delivery system has been developed. Furthermore, precise control system that is composed of 3-axis linear stage and shutter has been used to fabricate truly three dimensional micro-structure. For confirming the feasibility of developed micro-stereolithography apparatus, the solidification experiments were conducted. The solidification widths and depths datum of photopolymer as varying scanning speed of the UV light have been obtained. Using developed apparatus, some micro structures were fabricated successfully.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.319-320
• /
• 2012

Large aperture optical modulator called optical shutter is a key component to realize time-of-flight (TOF) based three dimensional (3D) imaging systems [1-2]. The transmission type electro-absorption modulator (EAM) is a prime candidate for 3D imaging systems due to its advantages such as small size, high modulation performance [3], and ease of forming two dimensional (2D) array over large area [4]. In order to use the EAM for 3D imaging systems, it is crucial to remove GaAs substrate over large area so as to obtain high uniformity modulation performance at 850 nm. In this study, we propose and experimentally demonstrate techniques for backside etching of GaAs substrate over a large area having high uniformity. Various methods such as lapping and polishing, dry etching for anisotropic etching, and wet etching ([20%] C6H8O7 : H2O2 = 5:1) for high selectivity backside etching [5] are employed. A high transmittance of 80% over the large aperture area ($5{\times}5mm^2$) can be obtained with good uniformity through optimized backside etching method. These results reveal that the proposed methods for backside etching can etch the substrate over a large area with high uniformity, and the EAM fabricated by using backside etching method is an excellent candidate as optical shutter for 3D imaging systems.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.342-343
• /
• 2013

AlSb is a promising material for optical devices, particularly for high-frequency and nonlinear-optical applications. And AlSb offers significant potential for devices such as quantum-well lasers, laser diodes, and heterojunction bipolar transistors. In this work we study molecular beam epitaxy (MBE) growth of an unstrained AISb film on a GaAs substrate and identify the real-time monitoring capabilities of in situ spectroscopic ellipsometry (SE). The samples were fabricated on semi-insulating (0 0 1) GaAs substrates using MBE system. A rotating sample stage ensured uniform film growth. The substrate was first heated to $620^{\circ}C$ under As2 to remove surface oxides. A GaAs buffer layer approximately 200 nm- thick was then grown at $580^{\circ}C$. During the temperature changing process from $580^{\circ}C$ to $530^{\circ}C$, As2 flux is maintained with the shutter for Ga being closed and the reflection high-energy electron diffraction (RHEED) pattern remaining at ($2{\times}4$). Upon reaching the preset temperature of $530^{\circ}C$, As shutter was promptly closed with Sb shutter open, resulting in the change of RHEED pattern from ($2{\times}4$) to ($1{\times}3$). This was followed by the growth of AlSb while using a rotating-compensator SE with a charge-coupled-device (CCD) detector to obtain real-time SE spectra from 0.74 to 6.48 eV. Fig. 1 shows the real time measured SE spectra of AlSb on GaAs in growth process. In the Fig. 1 (a), a change of ellipsometric parameter ${\Delta}$ is observed. The ${\Delta}$ is the parameter which contains thickness information of the sample, and it changes in a periodic from 0 to 180o with growth. The significant change of ${\Delta}$ at~0.4 min means that the growth of AlSb on GaAs has been started. Fig. 1b shows the changes of dielectric function with time over the range 0.74~6.48 eV. These changes mean phase transition from pseudodielectric function of GaAs to AlSb at~0.44 min. Fig. 2 shows the observed RHEED patterns in the growth process. The observed RHEED pattern of GaAs is ($2{\times}4$), and the pattern changes into ($1{\times}3$) with starting the growth of AlSb. This means that the RHEED pattern is in agreement with the result of SE measurements. These data show the importance and sensitivity of SE for real-time monitoring for materials growth by MBE. We performed the real-time monitoring of AlSb growth by using SE measurements, and it is good agreement with the results of RHEED pattern. This fact proves the importance and the sensitivity of SE technique for the real-time monitoring of film growth by using ellipsometry. We believe that these results will be useful in a number of contexts including more accurate optical properties for high speed device engineering.