• 한국전자파학회논문지
• /
• 제8권1호
• /
• pp.1-12
• /
• 1997

우주전파신호 분석을 위한 음향광학 전파분광기를 제작하였다 이 시스템은 우주로부터 수신된 미약한 전파신 호를 분석하는 신호처리 장치로 레이저 공진기 광학계. 광편향소자와 CCD로 구성된다. 이 시스템은 전파 시호를 분석하는 기존의 필터뱅크, 자기상관 분광기와는 달리 레이저와 광학계를 사용하여 빔을 유도하고 전파신호를 광편향소자에 의해 초음파로 변환하여 레이저빔을 회절시키는 새로운 방식의 전파 분광기이다. 광원으로는 He-Ne 레이저를 사용하였으며, 1 GHz에서 2 GHz까지의 대역폭을 갖는 광대역 GaP 광편향소자를 사용였다 . 또한 광신호 검출을 위해 2,048 채널의 CCD를 제작하였다 본 연구에서는 음향광학효과에 대한 이론적 배을 설명하고 레이저 공진기를 이용한 광학계의 설계, 광학마운트의 제작, CCD Driver, 인터페이스 제작과 이를 이용한 전파 신호의 측정에 대해 논의하였다. 전파선호의 측정결과 0차광이 1차광을 간섭시켜 2,048채널 중 I,000채널의 대역폭을 갖는 분팡가 성능을 갖게 되었다.

• 한국세라믹학회지
• /
• 제50권6호
• /
• pp.454-459
• /
• 2013

Recently, remote phosphors have been reported for application to white LEDs to provide enhanced phosphor efficiency compared with conventional phosphor-based white LEDs. In this study, a remote phosphor was produced by coating via screen printing on a glass substrate with different numbers of phosphor coating. The paste consists of phosphor, lowest softening glass frits, and organic binders. The remote phosphor could be well controlled by varying the phosphor content rated paste. After mounting the remote phosphor on top of a blue LED chip, CCT, CRI, and luminance efficiency were measured and values of 5300 K, 62, and 117 lm/W were respectively obtained in the 80 wt% phosphor with 3 coating layers sintered at $800^{\circ}C$.

• 한국세라믹학회지
• /
• 제50권6호
• /
• pp.470-475
• /
• 2013

In this study, we report that effects of a filler with a high coefficient of thermal expansion on a sealant for high-temperature ($750{\sim}850^{\circ}C$) SOFC. We designed a $SiO_2-BaO-ZnO-B_2O_3-Al_2O_3$ glass system with a softening temperature higher than $750^{\circ}C$. The properties of the glass system show not only low volumetric shrinking but also low swelling. The glass system did not create a crystal phase during along-term heat treatment. We fabricated a seal gasket with 0, 10, 15, and 20 wt% cristobalite added as filler materials with glass powder. The coefficient of thermal expansion of the seal gasket increased according to cristobalite content. During along-term heat treatment, the leak rate decreased by about 5% after a heat treatment in an oxidizing atmosphere at $750^{\circ}C$ for 2000 h, also decreasing by about 6% after a heat treatment in a reducing atmosphere at $750^{\circ}C$ for 1000 h.

• 한국광학회지
• /
• 제10권3호
• /
• pp.188-194
• /
• 1999

Mitsunobu 반응을 이용하여 전기광학계수 $\gamma_{33}$크고 열적 .시간적으로 안정적인 폴리이미드(polyimide)계고분자 용액인 PI-SOT(폴리이미드계 4-[N,N-bis(hydroxyethyl)amino­4'­($\beta$­cyano-$\beta$­methylsulfonyl)vinyl]azobenzene)고분자를 합성하였다. C.C. Teng의 단순반사법을 이용하여 코로나 폴링으로 극성 배향시킨 PI-SOT 박막의 전기광학계수 $\gamma_{33}$의 열안정성 및 시간안정성을 파장 632.8 nm와 852nm에서 측정하였다. 그 결과 상온에서 전기광학계수$\gamma_{33}$은 파장 632.8nm서 25.12 pm/V이고, 852 nmsns 5.40pm/V였다. 이 값들은 상온에서 60일 이상 장기간 안정적으로 유지되었으며, $100^{\circ}C$의 고온에서도 10시간내에서 6% 이내로 안정된 값을 유지하였다.

• 한국세라믹학회지
• /
• 제51권6호
• /
• pp.533-538
• /
• 2014

Today, silicon and epoxy resin are used as materials of conversion lenses for white LEDs on the basis of their good bonding and transparency in LED packages. But these materials give rise to long-term performance problems such as reaction with water, yellowing transition, and shrinkage by heat. These problems are major factors underlying performance deterioration of LEDs. In this study, in order to address these problems, we fabricated a conversion lenses using glass, which has good chemical durability and is stable to heat. The fabricated conversion lenses were applied to a remote phosphor type. In this experiment, the conversion lens for white LED was coated on a glass substrate by a screen printing method using paste. The thickness of the coated conversion lens was controlled during 2 or 3 iterations of coating. The conversion lens fabricated under high heat treatment temperature and with a thin coating showed higher luminance efficiency and CCT closer to white light than fabricated lenses under low heat treatment temperature or a thick coating. The conversion lens with $32{\mu}m$ coating thickness showed the best optical properties: the measured values of the CCT, CRI, and luminance efficiency were 4468 K, 68, and 142.22 lm/w in 20 wt% glass frit, 80 wt% phosphor with sintering at $800^{\circ}C$.

• 한국세라믹학회지
• /
• 제53권5호
• /
• pp.529-534
• /
• 2016

Nanocrystalline powder of zirconia stabilized with 8 mol% yttria (YSZ) has been synthesized through oxalate process using $ZrOCl_2{\cdot}8H_2O$ and $Y(NO_3)_3{\cdot}6H_2O$ as starting materials. Understanding of the characteristic changes of YSZ powder as a function of processing conditions is crucial in developing dense and porous microstructures required for fuel cell applications. In this research, microstructure change, surface area, particle shape and particle size were measured as a function of different processing conditions such as calcination temperature, stirring speed and concentration of starting materials. The resultant crystallite sizes were calculated by XRD-LB (X-Ray Diffraction Line-Broadening) method, BET method, and morphology of the crystal was observed in TEM and FE-SEM. The TEM examination showed that the powder synthesized with 0.7 M of YSZ concentration had a spherical morphology with sizes ranging from 20 to 40 nm. However, the powder was gradually aggregated above 1.0 M of YSZ concentration with the aggregation being intensified as the YSZ concentration was increased.

• 한국구조물진단유지관리공학회 논문집
• /
• 제3권3호
• /
• pp.223-236
• /
• 1999

The need to monitor and undertake remidial works on large structures has greatly increased in recent years due to the appearance of widespread faults in large structures such as bridges and buildings, etc, of 20 or more years of age. The health condition of structures must be monitored continuously to maintenance the structures. In order to do in-situ monitoring, the sensor is necessary to be embedded in the structures. Fiber optic sensors can be embedded in the structures to get the health information in the structures. The fiber sensor was constructed with $3{\times}3$ fiber couplers to sense the multi-point strains and failure instants. The 4 RC (reinforced concrete) beams were made to 2 of A type, 2 of B type beams. These beams were reinforced by the reinforcing bars, and were tested under the flexural loading. The behavior of the beams was simultaneously measured by the fiber optic sensors, electrical strain gages, and LVDT. The states of the beams were interpreted by these all signals. By these experiments, There were verified that the fiber optic sensors could measure the structural strains and failure instants of the RC beams, The fiber sensors were well operated until the failure of the beams. It was shown that the strains of the reinforcing steel bar can be used to monitor the health condition of the beams through the flexural test of RC beams. On the other words, the results were arrived that the two strains in the reinforcing bar measured at the same point can give the information of the structural health status. Also, the failure instants of beams were well detected from the fiber optic filtered signals.

• 한국군사과학기술학회지
• /
• 제24권6호
• /
• pp.610-618
• /
• 2021

In this paper, a photonic-based microwave system technology is described, and a traveling-wave electro-optic modulator is designed and manufactured as a key component. The fabricated modulator is composed of a metal diffusion waveguide for optical transmission and a planar waveguide electrode on lithium niobate substrate for microwave transmission. The electro-optic response bandwidth of I and Q channels in a fabricated dual parallel Mach-Zehnder modulator were measured for 27.67 and 28.11 GHz, respectively. Photonic four times up-converted X-band frequency and linear frequency modulated signal were confirmed using the fabricated electro-optic modulator by S-band input signal. The confirmed broadband signal can be applied to a microwave system for surveillance and high-resolution ISAR imaging.

• 한국전기전자재료학회논문지
• /
• 제32권3호
• /
• pp.207-212
• /
• 2019

A flat-type piezoelectric ceramic ultrasonic transmitter was successfully fabricated for application in acoustic devices with cone-free diaphragms. The transmitter, possessing a center frequency of 40.6 kHz, exhibited a higher displacement characteristic for a multilayer type compared with a single layer type. Surface roughness treatment of an Al elastic diaphragm influenced a slight increase (1.1 dB) in the sound pressure level (SPL) at $10V_{rms}$ due to the enlarged surface area. The fabricated multilayer piezoelectric ceramic ultrasonic transmitter showed increasing SPL with increasing input voltage, with a maximum SPL of approximately 123.6 dB at $10V_{rms}$. This implies a doubly increased SPL density of $3.6dB/mm^3$, superior to that of a commercial open-type transmitter with a cone.

• 센서학회지
• /
• 제28권2호
• /
• pp.106-112
• /
• 2019

Flexible impact force sensors composed of piezoelectric PZT/PDMS composite sandwiched between Al/PET films were fabricated and their voltage signal characteristics were evaluated under varying impact forces for electronic mitt applications. The piezoelectric impact force sensor on an ethylene-vinyl acetate (EVA) substrate exhibited an output voltage difference of no greater than 40 mV a periodical impact test in with the impact load was increased by as much as 240 N by a restoration time of 5 s in a five-time experiment, implying good sensing ability. Moreover, the impact force sensor embedded four electronic mitts showed a reliable sensitivity of less than 1 mV/N and good repeatability under 100 N-impact force during a cycle test executed 10,000 times. This indicated that the fabricated flexible piezoelectric impact sensor could be used in electronic mitt applications. However, the relatively low elastic limit of substrate material such as EVA or poly-urethane slightly deteriorated the sensitivity of the impact sensor embedded electronic mitt at over 200 N-impact forces.