• Corrosion Science and Technology
• /
• v.14 no.3
• /
• pp.147-152
• /
• 2015

Corrosion of steel reinforcement is a major factor in the deterioration of harbour and bridge structure. Steel corrosion in concrete must be checked for assessing the condition of a reinforced concrete structure. There are several ways how to measure the corrosion condition of reinforced concrete, but the corrosion potential measurement is a very simple, rapid, cost-effective and non-destructive technique to evaluate the severity of corrosion in reinforced concrete structure, therefore commonly used by engineers. However some particular situations may not relate to the reinforcement corrosion probability and a simple comparison of the corrosion potential data with the ASTM C876 Standard on steel reinforcement corrosion probability could be meaningless and not give reliable informations because of environment factors as oxygen concentration, chloride content, concrete resistance. Therefore this paper explains the risk of corrosion assessment in reinforced concrete structure and how many factors can affect the reliability of the corrosion potential data.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.6
• /
• pp.189-196
• /
• 1996

We have studied sngle-frequency yield of 1.55${\mu}$m DFB lasers with uniform sinusoidal grating using an effective index transfer matrix method considering both threshold gain difference and spatial hole-burning effect. Optimum grating height and mirror reflectivities that maximize the single-frequency yield are found for a low-reflection (LR)/high-reflection(HR) mirror structure and a LR/as-cleaved miror structure for an assumed basic waveguide structure. LR/HR structure has a high yield of about 80% in a narrow range of grating height while LR/as-cleaved mirror structure has a low yield of about 50% in a relatively wide range of grating height. The effect of the low-reflection facet reflectivity is also studied.

• Journal of the Korean Society for Railway
• /
• v.1 no.1 s.1
• /
• pp.20-29
• /
• 1998

State of the art and current issues related with the RC and PSC structure system for the German magnetic levitation train "Transrapid" were investigated. The German magnetic levitation train adopted a new kind of a structure to enable high-speed transportation, which allows the use of the space over a ground. The loading from Transrapid is light-weight compared with a regular train due to load distribution to a supporting structure. Therefore, Transrapid is considered an economical and efficient transportation system, and is also an environmentally-sustainable structure. In this paper, the structural design and construction technology specific to a magnetic levitation train were discussed, and structural considerations related with an actual operation of the train were pointed out. In addition, the future research area of a magnetic levitation train was proposed.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.442-452
• /
• 2007

Korean trains pass many mountain areas, so the volume of structures like bridge and tunnel has large part of railway lines. Train speed-up naturally needs a straight line in railway, then structures are increasing, and this influences passenger's comfort and the safety of operation, and it needs more track maintenance. The stiffness of bridge and tunnel is higher than the soil in the roadbed in spite of dynamic difference in vibration and displacement. Differences in stiffness have more dynamic effects and increase the deformation and destruction in the track and roadbed. This study will measure periodically to structure's approaches which have very fast track irregularity and analyze dynamic differences and track irregularity near structure's approaches, so realize the cause of track irregularity of structure's approaches and use basic data for reasonably strengthening method of structure's approaches.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.04a
• /
• pp.686-690
• /
• 2012

The modal test has been carried out using the exciter machine to investigate the vibration characteristics of the hull and super structure of the ship. The conventional exciter acts only one(1) direction and the exciter should be reinstalled for different direction test, which consumes additional expense. The 3 axes exciter has been designed of which force acts three directions without reinstallation for efficient modal test of the ship. It consists of rotatable base frame structure and the clutch mechanism for the unbalances to excite three directions. And the 3 axes exciter for the local structure has been made in advance and its performance test was carried out in the laboratory. The developed 3 axes exciter shows the ability of three-directions excitation with simple operation and modal test for the various local structure of the ship will be performed.

• Proceedings of the KSR Conference
• /
• 2001.05a
• /
• pp.393-400
• /
• 2001

State of the art and current issues related with the RC and PSC structure system for the German magnetic levitation train were investigated. The German magnetic levitation train adopted a new kind of a structure to enable high-speed transportation, which allows the use of the space over a ground. The loading from Transrapid is light-weight compared with a regular train due to load distribution to a supporting structure. Therefore, Transrapid is considered an economical and efficient transportation system, and is also an environmentaly-sustainable structure, In this paper, the structural design and construction technology specific to a magnetic levitation train were discussed, and structural considerations related with an actual operation of the train were pointed out. In addition, the future research area of a magnetic levitation train was proposed.

• ETRI Journal
• /
• v.44 no.2
• /
• pp.260-273
• /
• 2022

This study presents a novel multilayer structure of parallel coupled-line bandpass filtercentered at 2.42 GHz with a fractional bandwidth value of approximately 19.4%. The designed filter can suppress harmonics with an appropriate frequency response by incorporating different techniques based on the multilayer technique. A combination of different techniques such as radial microstrip stubs and defected ground structure (DGS) and defected microstrip structure techniques are employed to suppress harmonics up to 5f₀. These techniques are used in two layers to suppress up to 5f₀. In addition, in this study, the effects of different parameters, such as the width of slot-line DGS, the angle of diagonal line slots in the upper layer, and the air gap between the two layers on the filter performance, are investigated. To verify the correct circuit operation, the designed filter is implemented and tested. The measurement results of the proposed filter are compared with the simulation results.

• KIEAE Journal
• /
• v.11 no.4
• /
• pp.87-94
• /
• 2011

This study was suggested to develop sustainable durability design system and proposed the plan to evaluate design conditions that meet the intended service life and $LCCO_{2}$ reduction level of reinforced concrete structure easily from the early design stage. For that the W/B and covering depth of the concrete structure were calculated through calculation of service life based on standard specification expression and the quantitative reduction rate of the vertical member of reinforced concrete structure by the calculated W/B was applied. Life cycle of building classified into construction stage, operation stage, maintenance stage, and demolition/disposal stage and the method of $CO_{2}$ evaluation of each stage was proposed. For construction stage, the major construction materials that take up over 80% $CO_{2}$ emitting during building construction were selected and the $CO_{2}$ evaluation method for 5 standard apartment houses was proposed. Also, for operation stage, $CO_{2}$ emission was calculated through calculation of heating load by energy efficiency rating certification system. For maintenance stage, $CO_{2}$ emission was calculated using concept of re-construction by life and for demolition/disposal stage was calculated with the use of construction standard estimate. As a result of the case study by such evaluation methods, 80 years of service life and 17 specifications of sustainable durability design that meet the 40% intended $LCCO_{2}$ reduction level were deduced. The Maximum $LCCO_{2}$ reduction rate was analyzed by 47.2%.

• Journal of the Korea Society of Computer and Information
• /
• v.20 no.4
• /
• pp.1-10
• /
• 2015

NAND flash systems require deletion operation and do not support in-place update, so the storage systems should use Flash Translation Layer (FTL). However, there are a lot of memory consumptions using mapping table in the FTL, so recently, many studies have been proposed to resolve mapping table overhead. These studies try to solve update propagation problem in the nand flash system which does not use mapping table. In this paper, we present a novel index structure, called CL-Tree(Cache List Tree), to solve the update propagation problem. The proposed index structure reduces write operations which occur for an update propagation, and it has a good performance for search operation because it uses multi-list structure. In experimental evaluation, we show that our scheme yields about 173% and 179% improvement in insertion speed and search speed, respectively, compared to traditional B+tree and other works.

• Korean Journal of Poultry Science
• /
• v.18 no.1
• /
• pp.57-66
• /
• 1991

The broiler industry in Korea has been gradually changing its structure of independent operation into integrated and coordinated production and marketing system. It was in 1960s when the broiler industry first tried the integrated effort, but never succeeded as it was expected since due mainly to growers' attitudes favorable for traditional operation and agribusiness' passive response on structure change. Until mid 1980s, however, a bit of partially integrated system had been evolved by several factor suppliers. Recent years have furthered its progress toward completely integrated pattern, the ultimate goal of broiler integration. It is true that the external factors including the GATT Negotiations through the Uruguay Round stimulated the people involved in the industry to find the way of making it competitive to survive in the open, liberalized world economic system rapidly emerging through the process of globalization. Once the industry realized the necessity of reducing the cost of production and improving the quality of it, the conclusion tended to come to the point of an entire structural alteration by means of integration rather than an improvement of a certain segment such as marketing. It is very obvious. therefore. that the movement toward the complete integration will speed up in a coming few years under the leadership of not only entrepreneurs but also producers group. According to a report. there were three almost complete integrators and thirteen partial integrators as of December, 1990, all of which eagerly directed toward the completely integrated system in due course . Among others as an advantage of integrated structure. the cost saving must be pointed out as the greatest one In a survey, it was estimated that the cost of dressed and ready-to-eat chicken could be lowered by 31.8 percent and 41.5 percent, respectively, over that to be under the independent, non-integrated system. As long as everybody concerned about the future of the industry in the open market mechanism realizes the importance of the structure change through an integration, the broiler sector of Korean agriculture shall be moving toward the direction of vertically and completely integrated structure in order to make it competitive, even to export, hopefully before 1995 or by the end of this century in any case.