• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.335-340
• /
• 2002

The focus of this experimental study is to verify the effect of openings in reinforced concrete deep beam. Main variables are opening depth, width and vertical locations but the shear span-to-overall depth ratio was fixed by 0.5. The experimental results about 8 deep beams which was tested under two equal symmetrically placed point loads are reported.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.4D
• /
• pp.593-600
• /
• 2006

Joint opening of jointed concrete pavement is caused by change in temperature and humidity of adjoined slab. The magnitude of joint opening influences on the load-transfer-efficiency and the behavior of sealant. If temperature or humidity decreases, joint opening increases. Generally maximum joint opening of a given joint is predicted by using AASHTO equation. While different magnitudes of joint opening at the individual joints have been observed in a given pavement section, AASHTO equation is limited to predict average joint opening in a given pavement section. Therefore the AASHTO equation may underestimate maximum joint for the half of joint in a given pavement section. Joints showing larger opening than the designed may experience early joint sealant failure, early faulting. Also unexpected spalling may be followed due to invasion of fine aggregate into the joints after sealant pop-off. In this study, the variation of the joint opening in a given pavement section was investigated based on the LTPP SMP data. Factors affecting on the variation are explored. Finally a probabilistic joint opening model is developed. This model can account for the reliability of the magnitude of joint opening so that the designer can select the ratio of underestimated joint opening.

• The Journal of Engineering Geology
• /
• v.5 no.1
• /
• pp.31-44
• /
• 1995

The puppose of this study is to propose the numerical modelling criteria for underground opening, rock mass continuum is regarded as homogeneous rock behaved linear elastic. The results of this study are summarized as follows: - Boundaries of the finite element mesh should be located at least 6 radii away from the center of the opening. - For circular openings, tension only developed when $K_0$ was less than one-fourAs the ratio of initial horiwntal to vertical stress increased, the inward springline movement increased and the inward crown movement decreased. - The displacement patterns developing for opening I shaped horse-shoe and opening II shaped powerstation are similar to those for circular openings. For both type opening I and opening II, stress concentrations develop at the intersection of the wall and floor. Greater stress concentrations are found for the type opening II.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.4
• /
• pp.40-47
• /
• 2022

The present study aimed to examine the effectiveness of different techniques for controlling the diagonal cracks at the corners of openings on the strength, deformation, and crack propagation in reinforced concrete walls. The crack control strip proposed in this study, the conventional diagonal steel reinforcing bars, and stress-dispersion curved plates were investigated for controlling the diagonal cracks at the opening corners. An additional crack self-healing function was also considered for the crack control strip. To evaluate the volume change ratio and crack width propagation around the opening, downsized wall specimens with a opening were tested under the diagonal shear force at the opening corner. Test result showed that the proposed crack control strip was more effective in reducing the volume change and controlling the crack width around the opening when compared to the conventional previous methods. The crack control strip with crack healing feature displayed the superior performance in improving the strength of the wall and reducing the crack width while healing cracks occurred in the previous tests.

• Journal of Korean Association for Spatial Structures
• /
• v.7 no.3 s.25
• /
• pp.119-124
• /
• 2007

Due to the deficit of section of web, the buckling strength of cellular beam become smaller than that of H-beam. In this thesis, we evaluate the buckling strength of web-post through non-linear F.E.M with opening distance-diameter ratio and opening diameter - web thickness ratio as essential variables. And also analyzes this comparing with the standard indicated in BS5950 Part 1.

• International Journal of Precision Engineering and Manufacturing
• /
• v.2 no.3
• /
• pp.19-26
• /
• 2001

In order to investigate the effect of single tensile overload on the short crack growth behavior under the out-of-plane cyclic bending moment, crack opening stresses were continuously measured by an elastic compliance method using strain gages. The characteristics of short crack growth after the single tensile overload are analyzed by the effective stress range ratio. Futhermore, the investigation was carried out with respect to various fatigue crack growth behaviors such as the plastic zone size effect on crack retardation, the retarded crack length and the number of cycles.

• 유체기계공업학회:학술대회논문집
• /
• 2006.08a
• /
• pp.573-574
• /
• 2006

This research deals with the wave transmission and dissipation problems for two dimensional regular waves and s vertical circular cylindersr. Using the unsteady mild slope equation, a numerical model has been developed to calculate the reflection and transmission of regular waves from a multiple-row vertical circular cylinders. In addition hydraulic model experiments have been conducted with different values of properties between the cylinders and opening ratio (distances) between the rows of the cylinders. It is found that the transmission coefficients decrease with decreasing the opening ratio and increasing the rows of vertical cylinders. Comparison between hydralic and numerical experiments results shows resonable agreement.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.5
• /
• pp.1193-1199
• /
• 1990

Effects of strain hardening exponents on the behavior of fatigue crack propagation are experimentally investigated. The retardation effect of fatigue crack propagation after single overloading is investigated in relation to strain hardening exponent and crack closure. A relationship between crack opening ratio and strain hardening exponents is inspected through an examination of the crack closure behavior. An empirical equation relating retardation effect of fatigue crack propagation after single overloading, percent peak load and strain hardening exponent of materials is proposed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.387-392
• /
• 2003

This study is put a focus on the identification of sound characteristics according to the interior configuration of sound absorption material and air gap. Noise barrier is general consists of front perforated panel, air layer, sound absorption material, air gap and back plate. Noise barrier is required to the NRC value of 0.7. The absorbing performance of the noise barrier relies on the opening ratio of the perforated panel and the efficiency of the absorbing material. This study has observed the effect of opening ratio and hole size, the increase of sound absorbing performance by the configurations of sound absorption material and air gap. New designed noise barrier is achieved the acoustical performance of 0.87 the measurement in a reveration room.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.14 no.3
• /
• pp.131-137
• /
• 2010

12 trial-scale wall panels are tested and evaluated to investigate the ultimate load capacity of axially loaded concrete walls with various opening configurations. The experimental tests have been undertaken to obtain data for the modification of existing equations. A new design equation has been generated using the precise test data and it incorporates the unique length factors. This new design equation for concrete walls with openings is then compared with existing code formulae.