• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.1
• /
• pp.59-66
• /
• 2011

In this paper, a co-planar waveguide(CPW)-fed zeroth-order resonant(ZOR) antenna with an improved radiation efficiency was built and tested. The unit cell of the proposed antenna consists of a series metal-insulator-metal(MIM) capacitor and a shorted shunt stub inductor. In order to reduce the antenna size and to achieve the high radiation efficiency two shorted shunt stub arms bent by 90 degree were connected to the ground plane through the via. The proposed antenna consisting of two unit cells has an open ended composite right/left-handed(CRLH) transmission line structure. As a result the dominantly radiating parts of the antenna comes from shunt stub arms and vertical vias. The total size of the fabricated zeroth-order resonant antenna is $0.22\;{\lambda}_0{\times}0.22\;{\lambda}_0$. The measured gain and efficiency of the fabricated antenna have been enhanced by 3.07 dBi and 75 %, respectively, at the zeroth-order resonant frequency of 2.97 GHz.

• ETRI Journal
• /
• v.31 no.3
• /
• pp.271-281
• /
• 2009

This paper presents a novel multiband microstrip-fed right angle slot antenna design technique for multiple independent frequency bands. The new technique uses various slot sizes at various appropriate positions. We first propose a tri-band slot antenna consisting of three right angle slots. Then, a quad-band slot antenna is developed with four right angle slots which achieves slant ${\pm}45^{\circ}$ linear polarization, omnidirectional pattern coverage, good antenna gain, and acceptable impedance bandwidths over all the operating frequency range. Moreover, an open-circuited tuning stub is introduced to achieve good impedance matching. Both proposed antennas are designed on a ground plane of RT/duroid 5880 substrate with a thickness of 1.575 mm. The real measurable results show that the desired frequencies used in wireless communication systems, namely, WLAN and WiMax, are efficiently achieved.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.2A
• /
• pp.167-173
• /
• 2008

In this paper, the flexible narrow bandpass filters (BPFs) with ${\lambda}$g/4 short and ${\lambda}$g/2 open stubs by microstrip line on duroid substrate are suggested. These BPFs with narrow bandwidth show flexible bandwidth with variation of the position of the stubs using the Qe (external quality factor) without changing the impedance value at microwave range. On the other hand, by replacing the series quarter-wavelength connecting lines with the equivalent T-shaped line of bandstop filter(BSF), the compact stub bandpass filter with harmonics suppression can be realized. The BPF with ${\lambda}$g/4 short stubs shows the insertion loss of 2.1 dB and the return loss of 18 dB and BPF with ${\lambda}$g/2 open stubs shows the insertion loss of 1.2 dB and the return loss of 21.9 dB at the center frequency of 5.8 GHz and the bandwidth of 10 %.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.12 no.6
• /
• pp.37-43
• /
• 2013

In this paper, an UWB (Ultra Wide Band) band-pass filter with open stubs using SIR (Stepped Impedance Resonator) structure is presented. The proposed band pass filter (BPF) has SIR structure instead of open stubs for UWB application with low insertion loss. The bandwidth of the proposed BPF is 103 % at the center frequency of 5.8GHz and the insertion and return losses are 0.17dB and 13.1dB, respectively. Also, the entire size of the proposed band-pass filter is $21.6{\times}17.8mm^2$.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.6
• /
• pp.1-10
• /
• 1996

Protocol specifications and service definitions for distributed open system applications are defined using ASN.1. Therefore, to implement an open system application likes MHS, it is necessary to have well defined encoding/decoding modules which translate ASN.1 protocol specifications into their transfer syntaxes. However, that work is usually tedius, time consuming, and error prone. In this paper, we designed and implemented a new ASN.1 tool set which includes a new ASN.1 run-time library, called HY BER/DER, and an enhanced ASN.1-to-C compiler, called HYASNC$^{+}$. HYASNC$^{+}$ automatically generates C language encoder/decoder stub files and heder files for basic ASN.1 types and subtypes defiend in X.208 recommandation, and all X400 MHS system macro definitions. And, we evaluated the performance of HYASNC$^{+}$ compiler and HY BER/DER run-tiem library, and tested the interoperability of ASN.1 run-time library.

• ETRI Journal
• /
• v.31 no.2
• /
• pp.201-208
• /
• 2009

This paper proposes a spiral-shaped power island structure that can effectively suppress simultaneous switching noise (SSN) when the power plane drives high-speed integrated circuits in a small area. In addition, a new technique is presented which greatly improves the resonance peaks in a stopband by utilizing ${\lambda}$/4 open stubs on a conventional periodic electromagnetic bandgap (EBG) power plane. Both proposed structures are simulated numerically and experimentally verified using commercially available 3D electromagnetic field simulation software. The results demonstrate that they achieve better SSN suppression performance than conventional periodic EBG structures.

• ETRI Journal
• /
• v.46 no.4
• /
• pp.716-726
• /
• 2024

An ultrawide stopband lowpass filter is reported using three stepped impedance resonators with high selectivity. The filter extends the stopband frequency range and attenuation, and two quarter-wave open stubs and three circular ground slots are introduced. The lumped and distributed equivalent models are derived and analyzed. The corresponding results are validated experimentally in a fabricated prototype. The prototype lowpass filter has a 3 dB cutoff frequency (f_c) of 2.9 GHz, and the stopband is extended up to 35 GHz (12.07f_c), with an attenuation level better than 20 dB throughout. The passband-to-stopband transition (3 dB-20 dB) bandwidth is 0.18 GHz, and the roll-off factor is 135 dB/GHz at 30 dB. The insertion loss is 0.3 dB at 1.6 GHz. The normalized circuit size of the proposed filter with respect to the guided wavelength is 0.04.

• Journal of IKEEE
• /
• v.12 no.4
• /
• pp.225-233
• /
• 2008

This paper presents a compact, low insertion loss, sharp rejection and wide band microstrip band pass filter that is composed rectangular loop resonator and step-impedance-open-stub(SIOS) for wireless data communication. The SIOS can be reduce length about 30% more than general 0.25${\lambda}$ stub. And stubs can have the advantage of tuning impedance magnitude. In order to demonstrate agrement of this paper prove, the optimized wide band pass filters are realized and experimented. A transmission line model used to calculate the frequency response of the new filters shows good agreement with measurements. The filter with perturbation stubs has four poles at rejection band, the poles are excited 3.610GHz, 4.265GHz at low frequency band, 8.494GHz, 9.056GHz at high frequency band. And the filter has 3dB fractional bandwidth of 57%(3.695GHz), an insertion loss of better than 0.37dB from 4.549GHz to 8.244GHz, and two rejection of greater than 30dB within 237MHz(4.312GHz${\sim}$ 4.549GHz) at low frequency band, 234MHz(8.244GHz-8.491GHz) at high frequency band.

• Advances in concrete construction
• /
• v.12 no.5
• /
• pp.399-409
• /
• 2021

The existing method to improve the coordination performance of the inner and outer parts of concrete-encased concrete-filled steel tube (CFST) composite columns by increasing the volume-stirrup ratio causes difficulties in construction due to over-dense stirrups. Thus, this paper proposes an open polygonal composite stirrup with high strength and high ductility CRB600H reinforced rebar, and seventeen specimens were constructed, and their axial compressive performance was tested. The main parameters considered were the volume-stirrup ratio, the steel tube size, the stirrup type and the stirrup strength. The test results indicated: For the specimens restrained by open octagonal composite stirrups, compared with the specimen of 0.5% volume-stirrup ratio, the compressive bearing capacity increased by 14.6%, 15.7% and 21.5% for volume-stirrup ratio of 0.73%, 1.07% and 1.61%, respectively. For the specimens restrained by open composite rectangle stirrups, compared with the specimen of 0.79% volume-stirrup ratio, the compressive bearing capacity increased by 7.5%, 6.1%, and -1.4% for volume-stirrup ratio of 1.12%, 1.58% and 2.24%, respectively. The restraint ability and the bearing capacity of the octagonal composite stirrup are better than other stirrup types. The specimens equipped with open polygonal composite stirrup not only had a higher ductility than those with the traditional closed-loop stirrup, but they also had a higher axial bearing capacity than those with an HPB300 strength grades stirrup. Therefore, the open composite stirrup can be used in practical engineering. A new calculation method was proposed based on the stress-strain models for confined concrete under different restrain conditions, and the predicted value was close to the experimental value.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.10
• /
• pp.1107-1116
• /
• 2007

In this paper, a broadband open stubs band pass filters which can suppress the second harmonics using Z-transform technique, is designed, fabricated and characterized. The proposed broadband filters integrate the band stop filter with the FSCS structure and ${\lambda}_g/4$ open stub in order to suppress the second harmonics. Due to insertion of BSF at input and output terminal, the size of the filter was increased in the conventional filter, however, in the proposed structure, the position of inverter that connects the stubs can be integrated between those stubs, thereby decreasing the size. So, it can be fabricated in the size of $18.7{\times}16.9mm^2$ which is smaller size than conventional one. The measured results of the proposed filters have center frequency of a 5.8 GHz with bandwidth of 95 %, insertion loss of 0.6 dB, return loss of 14 dB. The simulation results are consistent with measurement results. The filter is designed far X-band satellite communication and ITS applications.