• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 춘계학술대회 논문집
• /
• pp.819-823
• /
• 1996

In the large steel ingosts, void defects exhibiting microvoid shapes are inevitably formed in the V-segregation zone of the ingots during solidification. In the hot open-die forging process, material properties are improved by eliminating internal porosity. The void size is practically very small as compared with the huge large ingot. Thus, for deformation analysis of a large ingot, a massive number of elements are needed in order to describe a void surface and to uniform mesh sturcture. In the present work the Global/Local scheme has been introduced in order to reduce the computational time and to easily generate the mesh system as a void module of local mesh for obtaining the accurate solution around a void. The procedure of the global- local method consists of two steps. In the first step global analysis is carried out which seeks a reasonably good solution with a cpurse mesh system without describing a void. Then, a local analysis is performed locally with a fine mesh system under the size-criterion of a local region. The computational time has been greatly reduced. Though the work it has been shown that large ingot forging incorporation small voids can be effectively analyzed by using the proposed Global/Local scheme.

• 한국세라믹학회지
• /
• 제45권12호
• /
• pp.796-801
• /
• 2008

$LaGaO_3$ thin film was prepared on Ni-Fe metal porous substrate by Pulsed Laser Deposition method. By the thermal reduction, the dense $NiO-{Fe_3}{O_4}$ substrate is changed to a porous Ni-Fe metal substrate. The volumetric shrinkage and porosity of the substrate are controlled by the reduction temperature. It was found that a thermal expansion property of the Ni-Fe porous metal substrate is almost the same with that of $LaGaO_3$ based oxide. $LaGaO_3$ based electrolyte films are prepared by the pulsed laser deposition (PLD) method. The film composition is sensitively affected by the deposition temperature. The obtained film is amorphous state after deposition. After post annealing at 1073K in air, the single phase of $LaGaO_3$ perovskite was obtained. Since the thermal expansion coefficient of the film is almost the same with that of LSGM film, the obtained metal support LSGM film cell shows the high tolerance against a thermal shock and after 6 min startup from room temperature, the cell shows the almost theoretical open circuit potential.

• 대한기계학회논문집B
• /
• 제20권12호
• /
• pp.4036-4043
• /
• 1996

When a high-speed railway train enters a tunnel, a compression wave is generated ahead of the train and propagates along the tunnel, compressing and accelerating the rest air in front of the wave. At the exit of the tunnel, an impulsive wave is emitted outward toward the surrounding, which causes a positive impulsive noise like a kind of sonic boom produced by a supersonic aircraft. With the advent of high-speed train, such an impulsive noise can be large enough to cause the noise problem, unless some attempts are made to alleviate its pressure levels. In the purpose of the impulsive noise reduction, the present study tested the effect of porous walls on the compression wave propagating into a model tunnel. Experimental results were obtained using a shock tube with an open end. The results showed that the cavity/porous wall is very effective for the compression wave with a large nonlinear effect. The porosity of 30% is most effective for attenuation and pressure gradient reduction of the compression wave front. Also the impulsive noise reduction increases with increasing the length and height of the cavity, compared with the tunnel equivalent diameter.

• 한국세라믹학회지
• /
• 제43권5호
• /
• pp.277-283
• /
• 2006

A porous material with a surface layer was fabricated from glass abrasive sludge and expanding agents. The glass abrasive sludges were mixed with expanding agents and compacted into precursors. These precursors were sintered in the range of $700-900^{\circ}C$ for 20 min. The sintered porous materials had a surface layer with smaller pores and inner parts with larger pores. The surface layer and closed pores controlled water absorption. As the expanding agent fraction and the sintering temperature increased, the porosity and pore size increased. The porous materials with $Fe_2O_3$ and graphite as the expanding agents had a low absorption ratio of about 3% or lower while the porous material with $CaCO_3$ as the expanding agent had a higher absorption ratio and more open pores.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.533-536
• /
• 2006

A light-weight aggregate with a surface layer was fabricated using glass abrasive sludge and expanding agents. The glass abrasive sludges were mixed with expanding agents ($Fe_2O_3,\;graphite,\;CaCO_3$) and formed into precursors. These precursors were sintered in the range of $700-900^{\circ}C$ for 20min. The sintered light-weight aggregate had a surface layer with smaller pores and an inner region with larger pores. The surface layer and pores controlled the water absorption ratio and physical properties. As the expanding agent fraction and the sintering temperature increased, the porosity and pore size increased. The light-weight aggregate with $Fe_2O_3$ and graphite as the expanding agents had a low water absorption ratio while the porous material with $CaCO_3$ as the expanding agent had a higher water absorption ratio and more open pores.

• Carbon letters
• /
• 제18권
• /
• pp.24-29
• /
• 2016

High pollutant-loading capacities (up to 319 times its own weight) are achieved by three-dimensional (3D) macroporous, slightly reduced graphene oxide (srGO) sorbents, which are prepared through ice-templating and consecutive thermal reduction. The reduction of the srGO is readily controlled by heating time under a mild condition (at 1 10⁻² Torr and 200℃). The saturated sorption capacity of the hydrophilic srGO sorbent (thermally reduced for 1 h) could not be improved further even though the samples were reduced for 10 h to achieve the hydrophobic surface. The large meso- and macroporosity of the srGO sorbent, which is achieved by removing the residual water and the hydroxyl groups, is crucial for achieving the enhanced capacity. In particular, a systematic study on absorption parameters indicates that the open porosity of the 3D srGO sorbents significantly contributes to the physical loading of oils and organic solvents on the hydrophilic surface. Therefore, this study provides insight into the absorption behavior of highly macroporous graphene-based macrostructures and hence paves the way to development of promising next-generation sorbents for removal of oils and organic solvent pollutants.

• Nuclear Engineering and Technology
• /
• 제23권1호
• /
• pp.49-55
• /
• 1991

AUC공정으로 제조된 $UO_2$분말을 사용하여 소결체를 제조하여 미세 조직과 기공특성에 대하여 시험하였다. 개기공은 소결밀도 증가에 따라서 감소하였으며, 소결밀도 10.45 g/㎤ 이상에서는 거의 소멸하였다. 3$\mu$m보다 작은 크기의 둥근 기공이 모든 밀도에서 나타났고 낮은 밀도에서는 이것외에도 긴 기공이 관찰되었다. 같은 크기의 기공일지라도 밀도가 낮아지면 기공이 더욱 길게 나타났다. 기공크기에 따른 기공 면적의 분포는 mono 모우드이고, 2~3$\mu$m 기공크기에서 최대치를 보이는 분포를 보였다. 또한 밀도가 감소할수록 큰 기공에 관련된 면적이 증가하였다.

• Wind and Structures
• /
• 제32권2호
• /
• pp.105-114
• /
• 2021

This paper describes a wind tunnel test on a 1:25 scale model of TTU building with several adjustable openings in order to comprehensively study the characteristics of fluctuating internal pressures, especially the phenomenon of the increase in fluctuating internal pressures induced by tangential flow over building openings and the mechanism causing that. The effects of several factors, such as wind angle, turbulence intensity, opening location, opening size, opening shape and background porosity on the fluctuating internal pressures at oblique wind angles are also described. It has been found that there is a large increase in the fluctuating internal pressures at certain oblique wind angles (typically around 60° to 80°). These fluctuations are greater than those produced by the flow normal to the opening when the turbulence intensity is low. It is demonstrated that the internal pressure resonances induced by the external pressure fluctuations emanating from flapping shear layers on the sidewall downstream of the windward corner are responsible for the increase in the fluctuating internal pressures. Furthermore, the test results show that apart from the opening shape, all the other factors influence the fluctuating internal pressures and the internal pressure resonances at oblique wind angles to varying degrees.

• 생물환경조절학회지
• /
• 제29권1호
• /
• pp.9-19
• /
• 2020

대류열전달은 겨울철 온실 열손실의 중요한 원인이 되며, 일반적으로 복사열에 의한 손실보다 더 크다. 스크린의 대류열전달계수를 자연상태에서 측정한 연구가 수행된 바는 있지만 상하면의 재질이 동일하고 공극이 없는 스크린에 대해서는 적용을 할 수 없는 방법이다. 이러한 재질의 스크린은 한국에서 많이 사용되고 있으나 대류열전달 특성을 파악하는데 많은 어려움이 있는 실정이다. 본 연구에서는 공극이 없는 3가지 종류의 스크린에 대해 대류열전달계수를 구하였으며, 계수를 산정하기 위하여 복사열수지 이론에 근거하여 산정방법을 개발하였다. 실험장치에 스크린을 설치하고 일사량, 장파복사량, 대기온도, 스크린 및 흑색천의 표면온도, 풍속 등을 측정하였다. 스크린의 표면온도와 주변온도의 차이에 따른 대류열전달계수를 산정하였다. 풍속이 거의 없는 상태에서 온도의 차이가 증가함에 따라 계수는 감소하는 것으로 나타났다.

• Spatial Information Research
• /
• 제18권4호
• /
• pp.1-11
• /
• 2010

본 연구는 2차원적 도시특성변수를 이용한 기존 선행연구와 달리, 도시기하학적인 특성을 중심으로 도시열섬현상에 관한 설명모형을 구축하고 이에 대한 정책적 시사점을 제시하고 자하는 연구이다. 오하이오주 콜럼버스 도시(Columbus, Ohio)의 3차원 도시공간구축을 위하여 LiDAR 데이터가 활용되었고, 건축물의 외부공간을 구축하기 위하여 건물수치지도가 이용되었다. 또한 식생지수와 도시온도 자료를 추출하기 위하여 Landsat TM 영상의 band 3, band 4, Thermal band 가 이용되었다. 복잡한 자료 추출 과정을 통해 획득된 6가지 변수들(건물의 총 부피, 건물의 총 표면적, 평균 건물의 높이-도로폭 비율, 공극률, 건물바닥면적비율, 식생지수)을 도입하여 단순회귀 및 다중회귀 모형을 구축하였다. 회귀모형구축에 있어서는 비선형관계에 있는 변수를 선형화하기 위해 Box-Tidwell 변형기법을 적용하였으며 최적화된 변수변형을 통한 선형회귀모형을 구축하였다. 공극률, 식생지수, 건축 표면적 변수로 추정된 다중회귀모형은 전체 온도변이의 57%를 설명할 수 있는 것으로 나타났으며, 도시열섬을 저감시키기 위한 다양한 정책수립(오픈스페이스 확대정책, 옥상녹화, 벽면녹화 등)에 의미있는 결과를 제공하였다.