• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.1
• /
• pp.46-51
• /
• 2006

This paper reports on the effects of silicone oils, used as processing agents, on the recovery of hydrophobicity of silicone rubber. The recovery of hydrophobicity was evaluated by the measuring the contact angle, the surface electrical resistance and SEM. Here, we formed artificial contamination on the surface of samples, which scratched by sand papers and alumina powders. There was small recovery of hydrophobicity on the surface of SIR-A that silicone oil was not added. In both oil-added samples, SIR-B and SIR-C, recovery of hydrophobicity was achieved greatly. The surface of SIR-C showed that a lot of silicone oil was observed due to migration of oil, relatively in comparison with SIR-B. The tendency of recovery of hydrophobicity expressed by contact angle was in a good agreement with electrical property as determined by surface resistivity.

• Computers and Concrete
• /
• v.10 no.4
• /
• pp.349-360
• /
• 2012

In this paper, compressive strength, water permeability and abrasion resistance of concretes containing high volume fine fly ash (FFA) and fine ground palm oil fuel ash (GPA) were studied. Portland cement type I was replaced with FFA and GPA at dosages up to 70% by weight of binder. Ground river sand (GRS) was also used to replace Portland cement in order to indicate the level of filler effect. Results indicated that FFA was slightly more reactive than GPA. The replacement of 40-70% of FFA produced concretes with compressive strength, permeability and abrasion resistance comparable to those of normal concretes. The incorporation of GPA slightly reduced the performances of concretes as compared to those of FFA concretes. The reduction of Portland cement was partly compensated by the increase in pozzolanic activity of the fine fly ash and palm oil fuel ash and thus enabled the large replacement levels.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.12 no.6
• /
• pp.541-549
• /
• 2000

The present study experimentally investigated the effect of refrigeration oil on the condensation heat transfer for R-407C and R-22 in a microfin tube with a U-bend. POE oil ($74.1\;\textrm{mm}^2/s,\;40^{\circ}C$,) and mineral oil $62.5\;\textrm{mm}^2/s,\;40^{\circ}C$,) were used for R-407C and R-22 respectively Experimental parameters were an oil concentration from 0 to 5%, a mass flux from 100 to $400kg/m^{2}s sand an inlet quality from 0.5 to 0.9. The enhancement factors for both R-22 and R-407C refrigerants at the first straight section decreased continuously as the oil concentration increased. They decreased rapidly as the mass flux decreased and the inlet quality increased. The heat transfer coefficients in the U-bend showed the maximum at the $90^{\circ}$/TEX> position. The heat transfer coefficients at the second straight section within the dimensionless length of 48 were larger by a maximum of 33% than the average heat transfer coefficient at the first straight section.

• Economic and Environmental Geology
• /
• v.49 no.3
• /
• pp.213-224
• /
• 2016

Non-conventional resource and alternative energy were researched for predicting oil peak. In this study, one of many non-conventional resources, specifically oil-sands, was investigated due to the increasing interest of oil-sands plant modularization in permaforst areas for reducing the construction periods through modular transportation while limiting local construction workers. Hence, tehcnological trends were analyzed for oil-sand plant modularization. Data used were between 1994 and 2015 for patent analysis while targets included Korea, US, Japan, Europe and Canada. Technology classification system consisted of mining, steam assisted gravity drainage(SAGD), separation/upgrading/tailors ponds, module design/packaging, module transportation and material/maintenance. Result of patent analysis, patent application accounts 89% in US and Canada. The main competitive companies were Shell, Suncor and Exxon-mobil. Unlike other oil developments, oil-sands have a long-term stable production characteristic, hence, it is important to ensure the competitiveness of oil-sands for obtaining a patent in the long run.

• Corrosion Science and Technology
• /
• v.7 no.6
• /
• pp.350-361
• /
• 2008

Canada's oil sands contain one of the largest reserves of oil in the world. According to recent estimates, there are nearly 180 billion barrels of oil in the Canadian oil sands trapped in a complex mixture of sand, water and clay. More than 40 companies have been currently operating or developing oil sands facilities since the first production in 1967. The process of oil sands upgrading is similar with down stream refinery, but the corrosion environment in upgrading refinery is often more severe than in the refinery because of high chlorides, mineral contents, carbonic acid, heavy viscosity and fouling, higher naphthenic acid [$NA-R(CH_{2})nCOOH$], and greater sulfur contents. Naphthenic acid corrosion (NAC) which is one of the most critical corrosion issues in up & downstream refinery plants was observed for the first time in 1920's in refinery distillation processes of Rumania, Azerbaizan (Baku), Venezuela, and California. As a first API report, the 11th annual meeting stated sources and mechanism of NAC in early 1930's. API has been developing the risk base standards, such as API RP580, 571, and Publication 581 which are based on the worst NAC damage in the world since 2000. Nevertheless not only the NAC phenomena and control in Canadian sands oil process are not much widely known but also there are still no engineering guidances for the Canadian sands oil in API standards. This paper will give NAC phenomina and materials selection guidance against NA environment in Canadian oil sands upgrading processes.

• Tribology and Lubricants
• /
• v.33 no.1
• /
• pp.31-35
• /
• 2017

Recently, international attention has been focused on the development of non-traditional energy resources such as shale gas and oil sands, due to the steep increase in the demand for natural resources. The materials incorporated in an oil gas plant module experience extreme environments, and are prone to various problem such as fracture, corrosion and abrasion due to low-temperature brittleness. In order to improve the plant life, it is necessary to perform characteristics study and performance evaluation of the materials. In particular, this paper explains the main set of materials which are most frequently used in oil sands plant project. In order to investigate wear characteristics, the authors carried out abrasive wear tests of TP 316, stainless steel and SS 400, structural rolled steel. For the analysis of the abrasive wear resistance of an oil sands plant, the authors carried out the test according to ASTM G 105 "Standard Test Method for Conducting Wet Sand/Rubber Wheel Abrasion Test" standard guidelines. The authors have derived the results from the data associated with the loss of mass with respect to wear rate. During the test, for a given wear length for 10,000 revolutions, the rotational speed and applied force of the rubber wheel were varied.

• Economic and Environmental Geology
• /
• v.48 no.4
• /
• pp.361-369
• /
• 2015

Interest of unconventional Oil and Gas, which is produced in a different way, has been increasing due to exhaustion of traditional oil and gas. However production of unconventional Oil and Gas is closely related to its technology level. Accordingly in this research, we can analyze technology level of unconventional Oil and Gas with country/sector/year patent analysis. Through the result of this research, U.S is highest patent application national, patent application in oil sand is increasing. In addition, oil sands-realated patents and shale oil-realated patents applying actively in early 1970's and since the mid-1980's showed a decreasing trend. And patent application in unconventional oil and gas has been increasing due to the rise in the oil price 2000's.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.44 no.3
• /
• pp.271-276
• /
• 2024

Traditional oil, a depleting resource, accounts for only one-third of the world's oil reserves, so research and cases of utilizing non-traditional oil as a resource are continuously increasing. However, unconventional oil contains bitumen containing solid particles such as sand, and because it is exposed to a high temperature and high pressure environment, deformation can frequently occur in oil pipelines. Therefore, variables such as material, thickness, and angle that can affect the deformation of the oil pipeline were derived and applied to the oil pipeline, and finite element analysis was performed using the Ansys program. As a result of finite element analysis, deformation and maximum load capacity were derived. Afterwards, the same analysis was performed by modeling an optimized oil pipeline by combining the factors with the best deformation resistance and maximum load capacity. As a result of the analysis, the effect of reducing deformation and increasing the maximum load capacity by about 30 % was confirmed, and factors for suppressing deformation when analyzing oil pipelines were derived.

• The KSFM Journal of Fluid Machinery
• /
• v.19 no.3
• /
• pp.43-47
• /
• 2016

Pile foundations constructed on extremely cold regions cause serviceability problems of superstructures from repeated actions of ground freezing and thawing. Oil sand module plants are mainly constructed on seasonal frozen ground. Due to the freezing and thawing actions of grounds, vertical movements of piles have been observed. To solve these erratic pile movement problems, thin vertical layer of PET aggregates is installed around the pile shaft to prevent potential unfavorable pile movements. There is no known method to calculate "thin PET aggregate layer" -surrounded pile shaft resistance (capacity) against vertical loads; therefore, this experimental research is conducted. Specifically, in this study, horizontal (normal) pressures on pile shaft were assessed varying PET aggregate layer thickness based on the experiment.

• The KSFM Journal of Fluid Machinery
• /
• v.19 no.3
• /
• pp.37-42
• /
• 2016

The demand for wireless technology in plant structure has recently been increasing due to several advantages such as installation cost reduction, easy placement, easy extension and aesthetic benefits. Among the many wireless technologies, ZigBee is one of the most useful for plant structure; a wireless plant networking system can be configured using ZigBee alone. This research proposes a ZigBee to use for extreme cold region and thereby enable integration of wired and wireless plant monitoring systems. In this study, in order to assess the performance of ZigBee measured data by thermocouple were examined based on the results from laboratory tests between existing ZigBee and developed ZigBee. From the experiment results, performance of developed ZigBee in harsh environment can be increased well.