• Ocean Systems Engineering
• /
• v.10 no.1
• /
• pp.25-47
• /
• 2020

A study of the wave conditions for the Asabo offshore location at the Qua Iboe oil field in Eastern Nigeria has been carried out. Statistical analysis was applied to three (3) years of data comprising spectral periods, Tp and significant wave heights, H_s. The data was divided into two (2); data from October to April represents one set of data and data from May to September represents another set of data. The results were compared with similar studies at other locations offshore of West Africa. It was found that there is an absence of direct swellwaves from the Southern Ocean reaching the location under study (the Asabo site). This work suggests that the wave system is largely emanating from the North Atlantic storms. The presence of numerous islands near the Asabo location shields the site from effects of storms from south west and therefore swells from the Southern Ocean. It is noted that the local wind has little or no contribution. An H_s maximum of 2 m is noted at the Asabo offshore location. It is found that the Weibull distribution best describes the wave distribution at Asabo. Thus, the Weibull distribution is suggested to be adequate for long term prediction of extreme waves needed for offshore design and operations at this location.

• Journal of the Korean Society of Industry Convergence
• /
• v.23 no.4_2
• /
• pp.569-581
• /
• 2020

Since the dehydration packages of offshore plant deal directly with oil & gas, there is a great risk of fire and explosion during operation. Therefore, this study performed risk assessment through HAZard & OPerability (HAZOP) for solid desiccant dehydration package that can remove water component of natural gas in offshore floating liquefied natural gas (LNG) production facilities below 0.1 ppmv. The risk matrix was determined by dividing the likelihood and the severity into five levels separately by asset, life, environment and reputation. The piping & instrumentation diagram (P&ID) of the dehydration package was divided into 9 nodes. Total 22 deviations were assessed in consideration of the adsorption and desorption conversion cycle. A risk assessment based on deviations revealed 14 major hazards. Three representative types of hazards were open/close failure of the control valve, control failure of the heater, and abnormal operation of the regeneration gas cooler. Finally, we proposed the installation of additional safety devices to improve safety against these major hazards, such as safety instrumented functions, alarms, etc.

• Journal of Ocean Engineering and Technology
• /
• v.33 no.3
• /
• pp.205-213
• /
• 2019

Recently, because of the global recession of the offshore plant industry and low-cost orders, there has been increasing interest in strengthening the competitiveness of domestic companies for the design and production technologies of offshore plants. However, in the offshore plant design field, the Plant Design Management System (PDMS), which is a 3D CAD program for plant layout developed by AVEVA Marine, is already commonly used as offshore plant design software and widely used in large domestic shipyards and cooperative design companies. Under this background, we have been thinking about ways to design better with the existing software. In this study, we developed a parametric design program to maximize the efficiency and reduce the working time for offshore plant electrical outfit production design based on the Programmable Macro Language (PML) of PDMS. We also examined its performance. By applying the developed program to the offshore plant module selected as an application example, it was confirmed that a 50% improvement in the work efficiency of cable tray design could be obtained compared with the existing method, with work efficiency improvements of 80% or more in other field design work.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.13 no.1
• /
• pp.511-525
• /
• 2021

Aluminium outfitting is widely used in offshore platforms owing to its anti-corrosion ability and its light weight. However, various standards exist (ISO, NORSOK and EN) for the design of handrails used in offshore platforms, and different suppliers have different criteria. This causes great confusion for designers. Moreover, the design load required by the standards is not clearly defined or is uncertain. Thus, many offshore projects reference previous project details or are conservatively designed without additional clarification. In this study, all of the codes and standards were reviewed and analysed through prior studies, and data on variable factors that directly and indirectly affect the handrails applied to offshore platforms were analysed. A total of 50 handrail design load scenarios were proposed through deterministic and probabilistic approaches. To verify the proposed new handrail design load selection scenario, structural analysis was performed using SACS (offshore structural analysis software). This new proposal through deterministic and probabilistic approaches is expected to improve safety by clarifying the purpose of the handrails. Furthermore, the acceptance criteria for probabilistic scenarios for handrails suggest considering the frequency of handrail use and the design life of offshore platforms to prevent excessive design. This study is expected to prevent trial and error in handrail design while maintaining overall worker safety by applying a loading scenario suitable for the project environment to enable optimal handrail design.

• International conference on construction engineering and project management
• /
• 2022.06a
• /
• pp.204-212
• /
• 2022

Recently, the Korean government has been actively promoting the smart city as their strategic agenda. However, to build smart cities that are greener, the authors believe it is essential to rapidly transit conventional energy sources such as fossil fuels to renewable energy. Although there is a big potential for Offshore wind in Korea, there has not been a full-scale commercial offshore wind farm until today. Since Korea is relatively a new market compared to the EU, it can be risky for developers. The authors will introduce risk management best practices in the offshore wind industry applicable to the Korean environment. This paper will mainly introduce an offshore wind project size of 99 MW. The project is expecting a Finance Close (FC) in Q3 2022, so the project team has prepared a risk register with over 150 risks and levers throughout the project lifecycle. Overall risks include risks with Development Expenditure (DEVEX) impact, a Capital Expenditure (CAPEX) impact, and an Operating Expenditure (OPEX) impact. Based on the identified risks, a more qualitative assessment of Cost and Schedule Impact was conducted. In conclusion, a Monte Carlo simulation was performed to propose a quantitative risk assessment to evaluate a benchmark contingency of the project cost.

• Journal of Ocean Engineering and Technology
• /
• v.26 no.3
• /
• pp.46-54
• /
• 2012

More than 70% of the accidents that occur on offshore installations stem from hydrocarbon explosions and fires, which, because they involve blast effects and heat, are extremely hazardous and have serious consequences in terms of human health, structural safety, and the surrounding environment. Blast barriers are integral structures in a typical offshore topside module to protect personnel and safety critical equipment by preventing the escalation of events caused by hydrocarbon explosions. Many researchers have shown the adequacy of the simple design tool commonly used by the offshore industry for the analysis and design of blast walls. However, limited information is available for corrugated blast wall design with explosion impact response characteristics. Therefore, this paper presents a parametric study on the explosion impact response characteristics of an offshore installation's stainless steel corrugated blast wall. This paperalso investigates and recommends design parameters for the structural design of a corrugated blast wall based on a nonlinear structural analysis of experiential results.

• Journal of Ocean Engineering and Technology
• /
• v.29 no.1
• /
• pp.9-15
• /
• 2015

We investigated the Reynolds number effects on the flow over a twisted offshore structure in the range of 3×10³≤ Re ≤ 1 × 10⁴. To analyze the effect of the twisted surface treatment, a large eddy simulation (LES) with a dynamic subgrid model was employed. A simulation of the cylindrical structure was also carried out to compare the results with those of the twisted offshore structure. As Re increased, the mean drag and lift coefficient of the twisted offshore structure increased with the same tendency as those of the cylindrical structure. However, the increases in the mean drag and lift coefficient of the twisted offshore structure were much smaller than those of the cylindrical structure. Furthermore, elongated shear layer and suppressed vortex shedding from the twisted offshore structure occurred compared to those of the cylindrical cylinder, resulting in a drag reduction and suppression of the vortex-induced vibration (VIV). In particular, the twisted offshore structure achieved a significant reduction of over 96% in VIV compared with that of the cylindrical structure, regardless of increasing Re. As a result, we concluded that the twisted offshore structure effectively controlled the flow structures with reductions in the drag and VIV compared with the cylindrical structure, irrespective of increasing Re.

• Ocean and Polar Research
• /
• v.39 no.1
• /
• pp.61-71
• /
• 2017

This study estimates the cost function through offshore fishery cost data and analyzed the economies of scale of Korea's offshore fishery. For the estimation of the cost function, translog cost function was used, and the analysis implemented the panel analysis of the panel data. Also, annual economies of scale of the offshore fishery and economies of scale of 14 offshore fisheries in 2015 were analyzed using translog cost function coefficient estimation. The analysis result of economies of scale of Korea's offshore fishery showed that with the exception of 2003, economies of scale exist in all periods of time. However, as it almost reaches the minimum efficient scale, it was revealed that further scale expansion will bring inefficiency. Thus, according to the analysis result, Korea's offshore fishery requires a scale reduction policy rather than scale expansion policy, and this seems to coincide with the current government's fishery reconstruction policy and its practice such as the fishing vessel buyback program. The analysis result of economies of scale of each offshore fishery in 2015 showed that economies of scale of each offshore fishery exists with the exception of five trawl fisheries such as large pair-trawl and large otter trawl and large purse seines. This strongly suggests that the five fisheries and Large Purse Seines with non performing economies of scale need urgent scale reduction and should be the first target for the government's fishery reconstruction policy.

• International Journal of CAD/CAM
• /
• v.6 no.1
• /
• pp.41-48
• /
• 2006

Nowadays major shipbuilding companies are trying to expand their business not only to shipbuilding but to offshore projects as well. DSME is one of them. DSME is trying to set up a flexible design and construction environment for shipbuilding and offshore construction in a single shipyard. The shipbuilding and offshore projects, however, have their unique technology but they need to be designed and constructed in one site. To support this new requirement, DSME has developed an integrated CAD system for ship and offshore projects. In this integrated design environment, the designers can design commercial ships and offshore projects in a flexible manner. Concurrent design is very important for ship and offshore design. As compared to the complexity of the product, the design period is quite short. In effect, the design system for the ship and offshore project has to support concurrent design. One essential point of concurrent design environment is a product model based design system. DSME has developed and implemented the 3D product model concurrent design environment based on Tribon M3. Tribon is a widely used CAD system in shipbuilding area that is developed by Tribon Solutions. DSME has both customized the Tribon system and developed in-house application systems to support its own design and production procedures. All the design objects are modeled in one common database to support concurrent design and accurate production. The major in-house development focused on the modeling automation and automatic drawing generation. During the drawing generation process many of the additional production information are also extracted from the 3D product model. In addition, several applications and functionalities have been developed to apply the shipbuilding based Tribon M3 system to offshore projects. The development of shape nesting, tubular connection, isometric drawing, grating nesting systems are the typical.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.1
• /
• pp.71-77
• /
• 2014

According to the increasement of demand for energy around globe, the concern degree of advanced countries for ocean energy including offshore wind power becomes excited. In domestic case, the government set up a goal that jumps up to the third ranked powerful nation of offshore wind in the world until 2020 and announced "The plan for 2.5-gigawatt wind farm off the south-west coast by 2019". Also the legal basis was created in order to support development of offshore wind power as 'A law on development, use, supply and promotion for New energy and renewable energy' was established by law. However to promote offshore wind power projects, there are much difficulties that developers should be applied by permitting use of public water surface and regulations of several domestic public institution. Therefore in this paper, we suggested an alternative to promote efficient offshore wind power projects by comparative analysis between domestic and foreign on regulatory pathways for siting and permitting offshore wind facilities.