• 대한기계학회논문집
• /
• 제6권3호
• /
• pp.211-221
• /
• 1982

Numerical analysis has been made on the heat transfer of two dimensional turbulent channel with a slat type blockage. Especially the effects of the height of slat and Reynolds number on the heat transfer characteristics of channel wall have been investigated. The methods of accelerating the convergence of the numerical solution of governing differential equation have been also examined. Line-by-line iterative method shows higher convergence rate than point-by-point iterative method for solution of both momentum equation and energy equation. The results show that the ratio of heat transfer coefficient of the wall near the blockage to that of the fully developed flow increase with increasing the ratio of blockage to channel height and decreasing the Reynolds number. These trends of variation of heat transfer coefficient with respect to the height of slat and Reynolds number agree with those of Sparrow's experiment on the pipe flow with slat type blockage.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2006년도 추계학술대회 논문집
• /
• pp.192-195
• /
• 2006

With increasing concerns of indoor air quality, $CO_2$ concentration in the public transportation, such as train, bus, and subway, draws big interests. The $CO_2$ concentration in the indoor air is regarded as index of ventilation status rather than that of adverse health effect. In this study, we measured the time-series of $CO_2$ concentrations in the KTX cabin during the journey of Gyongbu-line (Seoul-Busan) and Honam-line (Seoul-Mokpo) with the number of passengers on board. At the same time, the concentration of particulate matter (PM), temperature, humidity and gaseous pollutants including HCHO and VOCs were monitored. It is found that the $CO_2$ concentration was correlated linearly with number of passengers and was highly correlated with tunnel regions where the ventilation unit (flap) was closed.

• 한국대기환경학회지
• /
• 제26권2호
• /
• pp.219-233
• /
• 2010

Understanding the Nano size particles is of great interest due to their chemical and physical behaviors such as compositions, size distributions, and number concentrations. Therefore, accurate measurements of size distributions and number concentrations in ultrafine particles are getting required because expected losses such as diffusion for the instrument system from ambient inlet to detector are a significant challenge. In this study, the data using the computed settling losses, impaction losses, diffusion losses for the sampling lines (explored different sampling line diameters, horizontal length, number of bending, line angles, flow rates with and without a bypass), and diffusion losses for the Scanning Mobility Particle Sizers are examined. As expected, the settling losses and impaction losses are very minor under 100 nm, however, diffusion loss corrections for the sampling lines and the size instrument make a large difference for any measurement conditions with high numbers of particles smaller mobility size. Both with and without the loss corrections, which can affect to size distributions and number concentrations are described. First, 80% or more of the smallest particles (less than 10 nm) can be lost in the condition of a flow rate of 0.3 liter per minute and the length of sampling line of 1.0 m, second, total number concentrations of measurements are quite significantly affected, and the mode structure of the size distribution changes dramatically after the loss corrections applied. With compared to the different measurements, statistically diffusion loss corrections yield a required process of the ambient particle concentrations. Based on the current study, as an implication, a possibility of establishing direct revelation mechanisms is suggested.

• Journal of Biosystems Engineering
• /
• 제36권6호
• /
• pp.461-466
• /
• 2011

The purpose of this study is basically for the use of simulations to enhance productivity. In this paper, the optimal number of allocation in a small and medium industry which produces eleutherococcus senticosus sap, is performed using simulations. The simulation model was developed under considerations of production layout, process & operation, process time, total work time, work in process (WIP), utilization, failure rate, and operation efficient as inputs, and was validated with careful comparisons between real behaviors and outputs of the production line. Therefore, we can evaluate effects and changes in productivity when some strategies and/or crucial factors are changed. Although too many workers and machines could decrease productivity, the eleutherococcus senticosus sap production line in this paper has been maintained many machines. To solve this problem, we determined the optimal number of workers and machines that could not cause any interrupt in productions using simulations. This simulation model considers diverse input variables which could influence productivity, and it is very useful not only for the production line of Eleutherococcus Senticosus Sap, but also for other production lines with various purposes, especially, in the small and medium industries.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 제33회 추계학술대회논문집
• /
• pp.202-206
• /
• 2009

고속회전 연료분사시스템의 분무특성을 연구하였다. 분무특성에 영향을 주는 직렬식 분무오리피스의 직경을 각각 1mm, 2mm, 3mm, 4mm, 5mm와 분무오리피스 수를 3개, 6개, 12개로 변화시켜가며 분무특성 연구를 수행하였다. PDPA 측정 시스템을 이용하여 분무입자의 크기와 속도, 분무분포 등을 측정하였고, 고속카메라를 이용하여 분무가시화를 수행하였다. 실험결과, 분무오리피스로부터 분출된 단일 액주의 길이는 회전속도에 의해 제어되며, 분무입자의 크기(SMD)는 분무오리피스의 직경과 수가 증가함에 따라 작아지는 경향을 보였다. 결국 분무입자의 크기를 제어하는 기본 메커니즘은 분무 오리피스내의 액막의 두께에 의해 결정됨을 알 수 있었다.

• 한국도로학회논문집
• /
• 제14권6호
• /
• pp.111-120
• /
• 2012

PURPOSES : This study is to suggest suitable lighting facility installation plans by finding out driver's preference for combination of lighting facility installation among landscape factors that affect driver visibility in tunnels. METHODS : SD method is used to extract emotional factors that affect drivers' preference, Components of tunnel lighting facility installation are evaluated through conjoint analysis and it suggested relative importance of attributes and utility values. RESULTS : In the aspects of satisfaction levels of components of tunnel lighting facility installation, Tunnel side, two lows, and solid line arrangement type has the highest level of satisfaction. Extract emotional factors that affect drivers' preference are "safety", "openness" and "amenity." In addition, the result of analyzing relative importance of attributes of tunnel lighting facility shows that numbers of lighting array has the highest importance and lighting facility arrangement has the lowest importance. Result of analyzing partial utility shows that the 2 low type among number of lows, the solid line arrangement type between arrangement types, placing in the middle part among lighting facility arrangement were highly preferred. CONCLUSIONS : In the case of lighting numbers, utility values of the first line and the second line showed us a big difference. Increasing the number arrays in the future reformation of lighting facility installation combination will be effective in enhancing the utility of the driver.

• 대한전기학회논문지:전력기술부문A
• /
• 제51권6호
• /
• pp.290-295
• /
• 2002

The present assignment in installing the number of switches for distribution line was made on the basis of a normal feeder capacity 7,000kVA in KEPCO(Korea Electric Power Corporation), Korea. But the normal capacity is revised to 10000kVA in 1998. Even increasing limit of the operating capacity of the distribution lines enables us to give some benefit for the operation flexibility and investment cost of the distribution system. It is disadvantageous in the viewpoint of supply reliability. In distribution systems, switches are equipped to improve the reliability of distribution systems by minimizing the outage section due to fault and maintenance. Utility generally improves the reliability by minimizing the length of outage section, which is caused by fault and maintenance, through switch equipment on distribution system. In order to cope with the changes such as operation capacity, it is necessary to study whether the present criteria is reasonable or not, also to confirm whether the present criteria of installing switches in line is improved or not. In this study, we proposes the number of switch per feeder on the basis of present operation capacity in distribution system.

• 소성∙가공
• /
• 제11권5호
• /
• pp.405-413
• /
• 2002

A process planning system for cold forging of non-axisymmetric parts of comparatively simple shape was developed in this study. Programs for the system have been written with Visual LISP in AutoCAD. Shape of the product must be drawn with the solid line and the hidden line, and with the plane and front view, as well. At the plane, the system recognizes the external shape of non-axisymmetric portions - the number of the sides of the regular polygons and the radii of circles inscribing and circumscribing the polygon. At the front view, the system cognizes the diameter of axisymmetric portions and the height of the primitive geometries such as polygon, cylinder, cone, concave, convex, etc. The system perceives that the list developed from the solid line must be formed by the operation of forward extrusion or upsetting, and that the list developed from the hidden line must be formed by the operation of backward extrusion. The system designs the intermediate geometries again by considering clearance between workpiece and die, and then finally the billet diameter, in reverse order from the finished product, on the basis of volume constancy and using the operations, the forming sequence, the number of operations and the intermediate geometries which were already designed. The design rules and knowledges for the system were extracted from the plasticity theories, handbook, relevant reference and empirical knowledge of field experts. Suitability of the process planning was analyzed using SuperForge of FVM simulation package. The results of analysis showed good formability.

• 전기학회논문지
• /
• 제60권7호
• /
• pp.1385-1390
• /
• 2011

A coaxial-conical-radial transmission line conversion circuits have been investigated to realize a low loss high performance microwave power divider/combiner. In order to optimize the characteristics of the device, the power divider/combiner was designed separately with two parts-the inner part and the outer part. Utilizing the rectangular approximation of the outer part, we can design the low loss device which is not affected by the partition number N of the outer part. The small return loss which is lower than 20dB was obtained on the frequency range of 5.15GHz(7.45~12.60GHz). A conical connector was employed for smooth connection between the central coaxial line and the outer radial line. Making use of the $47^{\circ}$ and $90^{\circ}$ 2-stage conical connector, the return loss lower than 30dB was obtained on the operating frequency range of 5GHz. The total return loss of the designed divider/combiner was lower than 20dB on the frequency range of 5GHz for the partition number N=11, N=12 and N=16.

• 천문학회보
• /
• 제44권1호
• /
• pp.56.2-56.2
• /
• 2019

Measurement of the location of the baryon acoustic oscillation (BAO) feature in the clustering of galaxies has proven to be a robust and precise method to measure the expansion of the Universe. The best constraints so far have been provided from spectroscopic surveys because the errors on the redshift obtained from spectroscopy are minimal. This in turn means that the errors along the line-of-sight are reduced and so one can expect constraints on both angular diameter distance $D_A$ and expansion rate $H^{-1}$. But, future surveys will probe a larger part of the sky and go to deeper redshifts, which correspond to more number of galaxies. Analysing each galaxy using spectroscopy, which is a time consuming task, will not be practically possible. So, photometry will be the most convenient way to measure redshifts for future surveys such as LSST, Euclid, etc. The advantage of photometry is measuring the redshift of vast number of galaxies in a single exposure, but the disadvantage are the errors associated with the measured redshifts. Using a wedge approach, wherein the clustering is split into different wedges along the line-of-sight ${\pi}$ and across the line-of-sight ${\sigma}$, we show that the BAO information can be recovered even for photometric catalogues with errors along the line-of-sight. This means that we can get cosmological distance constraints even if we don't have spectroscopic information.