• Nuclear Engineering and Technology
• /
• 제51권2호
• /
• pp.533-538
• /
• 2019

The mechanical-collimation imaging is the most mature technology in prompt gamma (PG) imaging which is considered the most promising technology for beam range verification in proton therapy. The purpose of the present study is to compare the performances of two mechanical-collimation PG cameras, knife-edge (KE) camera and multi-slit (MS) camera. For this, the PG cameras were modeled by Geant4 Monte Carlo code, and the performances of the cameras were compared for imaginary point and line sources and for proton beams incident on a cylindrical PMMA phantom. From the simulation results, the KE camera was found to show higher counting efficiency than the MS camera, being able to estimate the beam range even for $10^7$ protons. Our results, however, confirmed that in order to estimate the beam range correctly, the KE camera should be aligned, at least approximately, to the location of the proton beam range. The MS camera was found to show lower efficiency, being able to estimate the beam range correctly only when the number of the protons is at least $10^8$. For enough number of protons, however, the MS camera estimated the beam range correctly, errors being less than 1.2 mm, regardless of the location of the camera.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2016년도 춘계 학술논문 발표대회
• /
• pp.239-240
• /
• 2016

The nuclear power plant construction project is a large-scale project that involved a daily maximum of thousands of workers. many equipment and laborers involved has been required consistently to minimize the need for safety through real-time safety management. But current nuclear power plant construction site is only managed to access of workers and equipments. The purpose of this study is the owner requirements reflects the characteristics of the nuclear power plant construction project integrated safety management system utilizing active RFID and GPS positioning technology.

• Nuclear Engineering and Technology
• /
• 제54권12호
• /
• pp.4522-4533
• /
• 2022

For severe accident assessment of reactor pressure vessel (RPV), it is important to develop an accurate model that can predict transient thermo-mechanical behavior of the RPV lower head under the given condition. The present study revisits the lower head failure with two- and three-dimensional finite element models. In particular, we aim to give clear insight regarding the effect of the three-dimensionality present in the distribution of the thickness and thermal load of the lower head. For a rigorous validation of the result, both the OLHF-1 and the OLHF-2 tests are considered in this study. The result suggests that the three-dimensional effect is not negligible as far as the failure location is concerned. The non-uniformity of the thickness distribution is found to affect the failure location and time. The thermal load, which may not be axisymmetric in general, has the most significant effect on the failure assessment. We also observe that the creep property can affect the global deformation of the lower head, depending on the applied mechanical load.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2001년도 춘계학술발표회요약집
• /
• pp.187.2-187
• /
• 2001

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2001년도 추계학술발표회요약집
• /
• pp.265.2-265
• /
• 2001

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1999년도 춘계학술발표회요약집
• /
• pp.456-456
• /
• 1999

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2005년도 춘계학술발표회
• /
• pp.299-300
• /
• 2005

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2005년도 춘계학술발표회
• /
• pp.974-975
• /
• 2005

• 비파괴검사학회지
• /
• 제23권1호
• /
• pp.38-44
• /
• 2003

원자력발전소의 안전성등급 기기에 적용되는 비파괴검사는 실제 결함을 실현한 시험편을 사용하여 결함탐지능력을 검증하도록 하는 기량검증이 요구되고 있다. 가동중인 원전에서 발생 가능한 균열으로는 기계적 피로균열, 열 피로균열 및 입계부식균열 등이 있으나 본 연구에서는 기계적 피로균열을 대상으로 하였다. 인장 피로하중을 사용하여 기계적 피로결함을 제조하기 위해서 시험편을 설계하였고 원하는 피로결함 파면의 조도를 얻기 위해서 인가하중의 크기 및 사이클 수를 조절하여 피로결함을 발생시켰다. 발생된 결함에 대한 정확한 크기와 위치에 대한 물리적 정보를 얻은 후에 결함이 설계된 크기와 위치에 존재하도록 기밀용접을 실시하였다. 기밀용접 후 잔여 용접 흠은 가스 텅스텐 아크용접 및 플럭스 코어드 아크용접으로 채워졌다. 최종 완성된 피로결함 시험편을 방사선투과검사 및 초음파탐상검사를 통하여 검사한 결과, 설계된 길이와 깊이로 피로결함이 형성되었음을 확인하였다.

• Nuclear Engineering and Technology
• /
• 제53권5호
• /
• pp.1556-1568
• /
• 2021

The plate-type fuel assembly adopted in nuclear research reactor suffers from complicated effect induced by non-uniform irradiation, which might affect stress conditions, mechanical behaviors and thermal-hydraulic performance of the fuel assembly. This paper is the Part II work of a two-part study devoted to analyzing the complex unique mechanical deformation and thermal-hydraulic characteristics for the typical plate-type fuel assembly under irradiation effect, which is on the basis of developed and verified numerical thermal-fluid-structure coupling methodology under irradiation in Part I of this work. The mechanical deformation, thermal-hydraulic performance and Mises stress have been analyzed for the typical plate-type fuel assembly consisting of support plates under non-uniform irradiation. It was interesting to observe that: the plate-type fuel assembly including the fuel plates and support plates tended to bend towards the location with maximum fission rate; the hot spots in the fuel foil appeared at the location with maximum thickness increment; the maximum Mises stress of fuel foil was located at the adjacent location with the maximum plate thickness increment et al.