• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.11a
• /
• pp.345-352
• /
• 2000

It is very important to evaluate the reliable nonlinear modulus characteristics of soils not only in the analysis of geotechnical structures under working stress conditions but also for the soil dynamic problems. For the evaluation of modulus characteristics of soils, various tests have been mostly employed in laboratory. However, different testing techniques are likely to have different ranges of reliable strain measurements, different applied stress level, and different loading frequencies, and the modulus of soils can be affected by these variables. For reliable evaluation, therefore, those effects on the modulus need to be considered, and measured values should be effectively adjusted to actual conditions where the soil is working. In this paper, to evaluate the modulus characteristics of soils, laboratory testing such as free-free resonant column (FF-RC), resonant column (RC), torsional shear (TS), static TX, and cyclic M/sub R/ tests were performed. The effects of strain amplitude, loading frequency, loading cycles, confining pressure, density, and water content on modulus were investigated. It is shown that the FF-RC test, which is simple and inexpensive testing technique, can provide a reliable estimation of small strain Young's modulus (E/sub max/), and the modulus evaluated by various laboratory tests are comparable to each other fairly well when the effects of these factors are properly taken into account.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.6
• /
• pp.67-79
• /
• 2005

The field plate load test has a good potential for determining modulus since it measures both plate pressure and settlement. Conventionally the modulus has been assumed to be a constant secant value defined from the settlement of the plate at a given load intensity. A constant modulus (modulus of subgrade reaction, k), however, may not be a representative value of subgrade soil under working load. Field strain(o. stress)-dependent modulus characteristics of subgrade soils, at relatively low to intermediate strains, are important in the pavement design. In this study, the field strain dependent moduli of subgrade soils were obtained using cyclic plate load test. Testing procedure and data reduction method are proposed. The field crosshole and laboratory resonant column tests were also performed to determine field nonlinear modulus at $0.001\%\;to\;0.1\%$ strains, and the modulus values and nonlinear trends are compared to those obtained by cyclic plate load tests. Both modulus values match relatively well when the different state of stress between two tests was considered, and the applicability of field cyclic plate load test for determining nonlinear modulus values of subgrade soils is verified.

• International Journal of Highway Engineering
• /
• v.9 no.1 s.31
• /
• pp.47-56
• /
• 2007

Resilient characteristics on unbound pavement materials have been adopted for design and nonlinear analysis of pavement structure under traffic loadings. However, relatively few studies have been done on the nonlinear resilient behavior of unbound materials in Korea. In addition to that, only the limited information is available for estimating the resilient modulus values on subgrade soils. In this study, a laboratory resilient-deformation test under repeated loadings is performed in order to establish the nonlinear characteristics of unbound subgrade soils in test roads. Then, a constitutive model that correlates the resilient modulus with moisture and stress state from field condition is proposed respectively. The results from all procedures are presented in this paper. Finally, a comparative analysis is conducted to identify the proper models in the stress dependent modulus and seasonal moisture condition of subgrade soils in test roads respectively.

• Geotechnical Engineering
• /
• v.13 no.5
• /
• pp.89-100
• /
• 1997

It is very improtant to evaluate the reliable nonlinear deformational characteristics of soils not only in the analysis of geotechnical structures under working stress conditions but also for the soil dynamic problems. Field testings such as crosshole and pressuremeter tests can be used to determine the modulus of soils under in-situ conditions, but it is not possible to determine the modulus over the entire strain amplitude range. Laboratory methods such as resonant column 1 torsional shear test can be used to determine the modulus over the whole strain amplitude range, but it is very difficult to obtain the representative undisturbed samples on the sixte. For the reliable evaluation of nonlinear deformation characteristics of soils on a typical site, small strain modulus obtained from field testy and nomalized modulus reduction curve determined by laboratory bests need to be combined. In this paper, laboratory and Held testy were performed at a sixte which consisted of granite wearthered residual boils to evaluate the nonlinear deformational characteristics of coils such as the effects of strain amplitude, loading frequency, confining pressure and sample disturbance. It has been shorn that when the effects of these factors are properly taken into account, the stiffness values evaluated by various field and labrotary tests are comparable to each other fairly well. Finally, the procedure to evaluate the nonlinear deformstional characteristics of the sixte was proposed.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.8 no.3
• /
• pp.87-93
• /
• 2008

The large scale shaker can be employed to measure linear and nonlinear shear moduli of soils in situ as a function of shear strain. The method involves applying dynamic loads on a surface foundation measuring the dynamic response of the soil mass beneath the foundation with embedded instrumentation. This paper focuses on the development of a framework of the inverse analysis for the interpretation of test data to estimate linear and nonlinear shear moduli of soils along with the necessity of the inverse analysis. The suggested framework is based on the nonlinear least squares but it uses two iterative loops to account for the nonlinear behavior of soil that sensors are not located. The validity of the suggested inversion framework is tested through a series of numerical parametric studies. An example use of the suggested inversion framework is also shown. Because the field condition may affect the accuracy of suggested method, it is important to conduct a preliminary inverse analysis to quantify the discrepancy between the estimated modulus and the baseline.

• 한국도로학회:학술대회논문집
• /
• 2002.10a
• /
• pp.255-262
• /
• 2002

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.1190-1200
• /
• 2010

A method was developed to determine resilient modulus for crushed rock-soil mixtures whose usage has been increased recently without engineering specifications. The method is based on the subtle different modulus called nonlinear dynamic modulus and was lately implemented in residual soils and engineered crushed-stones. Hereby. the same method was expanded to crushed rock-soil mixtures containing as large grain diameter as 300mm. The method utilize field direct-arival tests for the determination of maximum Young's modulus, and a large scale free-free resonant column test, which is recently developed to is capable to test as large grain diameter as 25mm, for modulus reduction curves. The prediction model of resilient modulus was evaluated for crushed rock-soil mixtures of a highway construction site at Gimcheon, Korea.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.2
• /
• pp.189-197
• /
• 2003

In this paper, deformation characteristics of fiber-mixed-soils were studied at small strain range(0.0001%～1%) using resonant column test and triaxial test, and reinforcement effect was evaluated by the measure of maximum shear moduli. The effects of the major parameters such as fiber content, aspect ratio and fiber type on reinforcement were comparatively assessed. The specimens were remolded from Jumunjin Sand randomly mixed with discrete polypropylene staple fibers. Maximum shear moduli of fiber-mixed-soils increased by up to 30% and modulus reduction was also restrained in nonlinear range. Shear moduli increased as the aspect ratio increases. The reinforcement was more effective with fibrillated fiber than with monofilament fiber. The most effective reinforcement was achieved with the specimen of 0.3 % fiber content.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2007.06a
• /
• pp.7-23
• /
• 2007

The shear wave velocity is directly related to the deformation characteristic of soils which is an engineering property represented by the shear modulus. This feature presents an opportunity of advantageous utilization of the shear wave velocity for deformation analysis in geotechnical engineering applications, since the deformation modulus is determined on strong theoretical basis, whereas penetration resistances such as N by SPT or qc by CPT rely on empirical relations. Furthermore, it is an engineering property that can be evaluated by performing the same basic measurement in the laboratory and field, and various problems in geotechnical engineering can be dealt with economically and reliably when the field and laboratory methods are combined effectively. In this article, assessment of nonlinear deformation characteristic of soils based on synergic use of the field and laboratory test results is described, and representative case histories of geotechnical applications of the shear wave velocity are illustrated.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03b
• /
• pp.968-976
• /
• 2004

In the paper, deformation characteristics of fiber-mixed-soils, mixed polypropylene staple fibers of 0.3% fiber content with sands of various gradation, and their effectiveness of reinforcement were evaluated. A series of Resonant Column tests were performed with specimens prepared with varying Uniformity Coefficient and constant Curvature Coefficient. Maximum shear moduli 01 fiber-mixed-soils were increased by up to 30% and modulus reduction was also restrained in nonlinear range. Normalized shear modulus reduction curves of fiber-mixed-soils shift close to the upper limit of Seed curd Idriss's curves and are located within narrower band than those of unmixed soils, which proves the effectiveness on stiffness increment by reinforcing soils with fibers.