• Korean Journal of Soil Science and Fertilizer
• /
• v.41 no.1
• /
• pp.55-64
• /
• 2008

A detailed understanding and appreciation of the important mechanisms operating at the soil:root interface, commonly identified as the rhizosphere, is critical for evaluating the potential for particular plant species to be successfully used as part of a phytoremediation technique. For specific plants, mechanisms may exist to overcome the inherit limitation of the phytoremediation technique when poorly mobile soil metals are of interest. In the present study, the influence of root exudates on the rhizosphere chemistry of soil and consequential metal uptake were investigated following culture of vetiver grass (Vetiveria zizanioides), recognized as a promising plant for land stabilization, in three different long-term contaminated soils and one non-contaminated control soil. The soil solution pH increased (0.3-1.1 units) following vetiver grass culture and dissolved organic carbon (DOC) also significantly increased in all soils with the highest increase in PP02 (23 to $173mg\;L^{-1}$). Chemical changes are contributed to root exudation by vetiver grass when exposed to high concentration of heavy metals. Chemical changes, consequently, influenced metal (Cd, Cu, Pb, and Zn) solubility and speciation in the rhizosphere. The highest solubility was observed for soil Ko01 (eg. 2091 and $318{\mu}g\;L^{-1}$ for Cd and Pb, respectively). Initial heavy metal solubility in soils varied with soil and either increased or decreased following vetiver grass culture depending on the soil type. An increase in pH following plant culture generally resulted in a decrease in metal solubility, while elevated DOC due to root exudation resulted in an increase in metal solubility via the formation of metal-DOC complexes. Donnan speciation demonstrated a significant decrease in free Cd and Zn in the rhizosphere and the concentration of Cd, Pb, and Zn in vetiver grass shoot was highly correlated with soluble concentration rather than total soil metal concentration.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.77-77
• /
• 2017

Titanium and its alloys offer attractive properties in a variety of applications. These are widely used for the field of biomedical implants because of its good biocompatibility and high corrosion resistance. Titanium anodizing is often used in the metal finishing of products, especially those can be used in the medical devices with dense oxide surface. Based on SAE/AMS (Society of Automotive Engineers/Aerospace Material Specification) 2488D, it has the specification for industrial titanium anodizing that have three different types of titanium anodization as following: Type I is used as a coating for elevated temperature forming; Type II is used as an anti-galling coating without additional lubrication or as a pre-treatment for improving adherence of film lubricants; Type III is used as a treatment to produce a spectrum of surface colours on titanium. In this study, we have focused on Type II anodization for the medical (dental and orthopedic) application, the anodized surface was modified with gray color under alkaline electrolyte. The surface characteristics were analyzed with Focused Ion Beam (FIB), Scanning Electron Microscopy (SEM), surface roughness, Vickers hardness, three point bending test, biocompatibility, and corrosion (potentiodynamic) test. The Ti-6Al-4V alloy was used for specimen, the anodizing procedure was conducted in alkaline solution (NaOH based, pH>13). Applied voltage was range between 20 V to 40 V until the ampere to be zero. As results, the surface characteristics of anodic oxide layer were analyzed with SEM, the dissecting layer was fabricated with FIB method prior to analyze surface. The surface roughness was measured by arithmetic mean deviation of the roughness profile (Ra). The Vickers hardness was obtained with Vickers hardness tester, indentation was repeated for 5 times on each sample, and the three point bending property was verified by yield load values. In order to determine the corrosion resistance for the corrosion rate, the potentiodynamic test was performed for each specimen. The biological safety assessment was analyzed by cytotoxic and pyrogen test. Through FIB feature of anodic surfaces, the thickness of oxide layer was 1.1 um. The surface roughness, Vickers hardness, bending yield, and corrosion resistance of the anodized specimen were shown higher value than those of non-treated specimen. Also we could verify that there was no significant issues from cytotoxicity and pyrogen test.

• Journal of Environmental Health Sciences
• /
• v.37 no.4
• /
• pp.267-278
• /
• 2011

Objectives: A great number of hazardous agents can be emitted from various types of art-creation in a fine arts college, but little data on exposure assessment has been published. A variety of processes encompassing toxic or non-toxic materials, tools, and components are involved in a sculptor work at a fine art college. The aim of this study was to assess exposure levels to particulates and noise during sculpture classes in a college of fine arts. Methods: Students in sculpture classes participated in this study. Mass, number, and surface area concentrations of particulates, noise level, temperature and relative humidity were monitored by both personal and area sampling during the tasks of metal, wood, and stone sculpting. Results: The number and surface concentration of particulates was the highest in the task of wood sculpting, followed by metal and stone work. The mass concentration of particulates was the highest in stone sculpting (personal GM 3.0 mg/$m^3$, GSD 3.0), followed by wood (personal GM 1.5 mg/$m^3$, GSD 1.8) and metal work (personal GM 0.95 mg/$m^3$, GSD 1.51) in that order. Occupational exposure limits (OEL) for particulates depends on the type of particulate. For wood dust, 86% (six subjects) of the personal samples and all area samples exceeded the Korean OEL for wood dust (1 mg/$m^3$), while 20% (two subjects) among stone sculpting students were exposed above the Korean OEL (10 mg/$m^3$). In contrast, metal sculpting did not exceed the OEL (5 mg/$m^3$). For noise level, metal sculpting students (Leq 95.1 dB(A) in the morning, 85.3 dB(A) in the afternoon) were exposed the most, followed by stone sculpting (88.3 dB(A)), and wood sculpting (84.8 dB(A)) in that order. Compared with the 90 dB(A) of the Korean OEL and 85 dB(A) of the American Conference of Governmental Industrial Hygienists' threshold limit value (ACGIH-TLV) for noise, 100% of the subjects (five subjects) and area samples during metal sculpting in the morning session exceeded both OELs, but only three subjects (60%) exceeded the ACGIH-TLV in the afternoon session. For stone sculpting, 50% (one subject) and 100% (two subjects) exceeded the Korean OEL and ACGIH-TLV, respectively, but the area sample did not exceed either OEL. During wood sculpting, two subjects (40%) exceeded ACGIH TLV. Conclusions: This work evaluated the sculptors' exposure to particulate matter and noise in fine art college, and revealed a poor working environment for the participating students. Effective measures should be supplemented by the administration of colleges.

• Korean Journal of Environmental Agriculture
• /
• v.28 no.2
• /
• pp.158-164
• /
• 2009

Biosorption uses adsorbents derived from non-living biomass and removes toxic metals from industrial wastewater. The objective of this research was to evaluate the potential of low cost biosorbents to remove heavy metal ions (Cd, Cu, Pb and Zn) from aqueous solutions using chemically modified rice husk and saw dust (Pseudotsuga menziesi, Quercus, Populus). Batch-type adsorption experiments were carried out using rice husk and saw dust treated with NaOH and/or tartaric acid in artificial wastewater 100 mg metal/L). The experimental results showed that the adsorption specificity of each biosorbent was Pb > Cu > Cd > Zn irrespective of the types of biosorbents. The adsorption capacity of Pb and Cu onto NaOH-treated sawdust was increased 2${\sim}$3 times compared to the untreated one. In addition, the tartaric acid treatment increased the adsorption capacity of rice husk for Zn and Cd approximately 5${\sim}$10 fold compared to the untreated one. Surface conditions and changes in functional groups by chemical modification of each biosorbent were confirmed by SEM and FT-IR. Overall, the results show that chemical modification increases the metal removal capacity of rice bran and sawdust.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.253-253
• /
• 2012

Low temperature SiOx film process has being required for both silicon and oxide (IGZO) based low temperature thin film transistor (TFT) for application of flexible display. In recent decades, from low density and high pressure such as capacitively coupled plasma (CCP) type plasma enhanced chemical vapor deposition (PECVD) to the high density plasma and low pressure such as inductively coupled plasma (ICP) and electron cyclotron resonance (ECR) have been used to researching to obtain high quality silicon oxide (SiOx) thin film at low temperature. However, these plasma deposition devices have limitation of controllability of process condition because process parameters of plasma deposition such as RF power, working pressure and gas ratio influence each other on plasma conditions which non-leanly influence depositing thin film. In compared to these plasma deposition devices, neutral beam assisted chemical vapor deposition (NBaCVD) has advantage of independence of control parameters. The energy of neutral beam (NB) can be controlled independently of other process conditions. In this manner, we obtained NB dependent high crystallized intrinsic and doped silicon thin film at low temperature in our another papers. We examine the properties of the low temperature processed silicon oxide thin films which are fabricated by the NBaCVD. NBaCVD deposition system consists of the internal inductively coupled plasma (ICP) antenna and the reflector. Internal ICP antenna generates high density plasma and reflector generates NB by auger recombination of ions at the surface of metal reflector. During deposition of silicon oxide thin film by using the NBaCVD process with a tungsten reflector, the energetic Neutral Beam (NB) that controlled by the reflector bias believed to help surface reaction. Electrical and structural properties of the silicon oxide are changed by the reflector bias, effectively. We measured the breakdown field and structure property of the Si oxide thin film by analysis of I-V, C-V and FTIR measurement.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.2
• /
• pp.83-93
• /
• 2012

Since reinforced soil walls were introduced in domestic civil engineering society in early 1980's, various reinforcing materials including metal strips, bar mats, and sheet-type reinforcement using geotextile, geogrid, and etc. have been developed for construction purpose. Especially, the geogrid has been mostly used as a reinforcement for reinforced earth structures. This paper describes the tensile behaviors of four types of domestic geogrids. Also, a series of the wide-width tensile tests on three types of geogrids were conducted to assess the reliability of the tensile strains in geogrid measured by strain gauge. The tensile strain by strain gauge is larger than real strain of the geogrid and a difference between strain gauge reading and real strain non-linearly increase with increasing the tensile strain. However, when the tensile strain is smaller than 3%, a difference between strain gauge reading and real strain is negligible.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.7
• /
• pp.44-50
• /
• 2009

High-pressured jetting is now widely used in the advanced cutting processes of polymers, metals, glass, ceramics and composite materials because of some advantages such as heatless and non-contacting cutting. Similarly to the focused laser beam machining, it is well known as a type of high-density energy processes. High-pressured jetting is going to be developed not only to minimize the cutting line width but also to achieve the short cutting time as soon as possible. However, the interaction behavior between a work piece and high-velocity abrasive particles during the high-pressured jet cutting makes the impact mechanism even more complicated. Conventional high-pressured jetting is still difficult to apply to precision cutting of micro-scaled thin work piece such as thin metal sheets, thin ceramic substrates, thin glass plates and TMM (Thin multi-layered materials). In this paper, we proposed the advanced high-pressured jetting technology by introducing a new abrasives supplying method and investigated the optimal process conditions of the cutting pressure, the cutting velocity and SOD (Standoff distance).

• Journal of the Korean Society of Propulsion Engineers
• /
• v.1 no.2
• /
• pp.12-21
• /
• 1997

Nowadays, non-pollution energy sources have been strongly needed because of the exhaustion of fossil fuels and serious environmental problems. Because wind energy can be enormously obtained from natural atmosphere, this type of energy has lots of advantages in a economic and pollution point of view. This study has established the aerodynamic and structural design procedure of the rotor blade with an appropriate aerodynamic performance and structural strength for the 500㎾ medium class wind turbine system. The aerodynamic configuration of the rotor blade was determined by considering the wind condition in the typical local operation region, and based on this configuration aerodynamic performance analysis was performed. The rotor blade has the shell-spar structure based on glass/epoxy composite material and is composed of shank including metal joint parts and blade. Structural design was done by the developed design program in this study and structural analysis, for instance stress analysis, mode analysis and fatigue life estimation, was performed by the finite element method. As a result, a medium scale wind turbine rotor blade with starting characteristics of 4m/s wind speed, rated power of 500㎾ at 12m/s wind speed and over 20 years fatigue life has been designed.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.22 no.3
• /
• pp.147-151
• /
• 2012

Carbon dioxide ($CO_2$) could be stored in the form of Ca and Mg compounds including alkaline earth metal by carbonation. The possibility of $CO_2$ storage was tested by using desulfurized ash from fluidized bed type boiler as raw material. Autoclave was used for maintaining the reaction pressure and temperature for the carbonation. The analysis of weight change rate, XRD, and TG/DTA proved that more than 15 % of carbonation rate was obtained under 10 $kgf/cm^2$ and $120^{\circ}C$-10 min.

• The Journal of Advanced Prosthodontics
• /
• v.7 no.4
• /
• pp.294-302
• /
• 2015

PURPOSE. The purpose of this study was to verify the clinical-feasibility of additive manufacturing by comparing the accuracy of four different manufacturing methods for metal coping: the conventional lost wax technique (CLWT); subtractive methods with wax blank milling (WBM); and two additive methods, multi jet modeling (MJM), and micro-stereolithography (Micro-SLA). MATERIALS AND METHODS. Thirty study models were created using an acrylic model with the maxillary upper right canine, first premolar, and first molar teeth. Based on the scan files from a non-contact blue light scanner (Identica; Medit Co. Ltd., Seoul, Korea), thirty cores were produced using the WBM, MJM, and Micro-SLA methods, respectively, and another thirty frameworks were produced using the CLWT method. To measure the marginal and internal gap, the silicone replica method was adopted, and the silicone images obtained were evaluated using a digital microscope (KH-7700; Hirox, Tokyo, Japan) at 140X magnification. Analyses were performed using two-way analysis of variance (ANOVA) and Tukey post hoc test (${\alpha}=.05$). RESULTS. The mean marginal gaps and internal gaps showed significant differences according to tooth type (P<.001 and P<.001, respectively) and manufacturing method (P<.037 and P<.001, respectively). Micro-SLA did not show any significant difference from CLWT regarding mean marginal gap compared to the WBM and MJM methods. CONCLUSION. The mean values of gaps resulting from the four different manufacturing methods were within a clinically allowable range, and, thus, the clinical use of additive manufacturing methods is acceptable as an alternative to the traditional lost wax-technique and subtractive manufacturing.