Response of the pipeline crossing fault is considered as the large strain problem. Proper estimation of the pipeline response plays important role in mitigation studies. In this study, an advanced continuum modeling including material non-linearity in large strain deformations, hardening/softening soil behavior and soil-pipeline interaction is applied. Through the application of a fully nonlinear analysis based on an explicit finite difference method, the mechanics of the pipeline behavior and its interaction with soil under large strains is presented in more detail. To make the results useful in oil and gas engineering works, a continuous pipeline of two steel grades buried in two clayey soil types with four different crossing angles of 30°, 45°, 70° and 90° with respect to the pipeline axis have been considered. The results are presented as the fault movement corresponding to different damage limit states. It was seen that the maximum affected pipeline length is about 20 meters for the studied conditions. Also, the affected length around the fault cutting plane is asymmetric with about 35% and 65% at the fault moving and stationary block, respectively. Local buckling is the dominant damage state for greater crossing angle of 90° with the fault displacement varying from 0.4 m to 0.55 m. While the tensile strain limit is the main damage state at the crossing angles of 70° and 45°, the cross-sectional flattening limit becomes the main damage state at the smaller 30° crossing angles. Compared to the stiff clayey soil, the fault movement resulting 3% tensile strain limit reach up to 40% in soft clayey soil. Also, it was seen that the effect of the pipeline internal pressure reaches up to about 40% compared to non-pressurized condition for some cases.
Objectives: Radix Ginseng has been used for thousands of years to treat a wide variety of diseases. Radix ginseng has also been used as a traditional medicine for boosting Qi energy and tonifying the spleen and lungs. Traditionally, its effect could be obtained orally. Nowadays, a new method, the injection of herbal medicine, is being used. This study was performed to investigate the single-dose intravenous toxicity of water-soluble ginseng pharmacopuncture (WSGP) in Sprague-Dawley (SD) rats. Methods: All experiments were carried out at Biotoxtech, an institute authorized to perform non-clinical studies under the regulation of Good Laboratory Practice (GLP). At the age of six weeks, 40 SD rats, 20 male rats and 20 female rats, were allocated into one of 4 groups according to the dosages they would receive. The WSGP was prepared in the Korean Pharmacopuncture Institute under the regulation of Korea-Good Manufacturing Practice (K-GMP). Dosages of WSGP were 0.1, 0.5 and 1.0 mL/animal for the experimental groups, and normal saline was administered to the control group. The rat's general conditions and body weights, the results of their hematological and biochemistry tests, and their necropsy and histopathological findings were investigated to identify the toxicological effect of WSGP injected intravenously. The effect was examined for 14 days after the WSGP injection. This study was performed under the approval of the Institutional Animal Ethics Committee of Biotoxtech. Results: No deaths were found in this single-dose toxicity test on the intravenous injection of WSGP, and no significant changes in the rat's general conditions and body weights, the results on their hematological and biochemistry test, and their necropsy findings were observed during the test. The local area of the injection site showed minial change. The lethal dose was assumed to be over 1.0 mL/animal in both sexes. Conclusion: These results indicate that WSGP is safe at dosages up to 1 mL/animal.
The CSR rule was defined by IACS as the unified rule for a commercial ship like a bulk carrier and a tanker. It have been required more strict conditions for various parts like loading conditions, the local and girder strength, fatigue strength, FEM for the ship rule. It was changed in many parts of the ship rules. In this paper, the mid-parts of 17.5K DWT bulk carrier were optimized by the CSR rule. On the other hand, the modified artificial life algorithms with multi-object functions were developed for optimizing the scantling. It is possible to find multi-global optimum solutions in the multi-object functions. And it is faster and efficient than the artificial life algorithm. First, to be optimizing the scantling and the weight by CSR rule, that is calculated by the CSR rule. The next, the result is re-calculated by the modified artificial life algorithm with multi-object functions. The optimized results which are satisfied with the CSR rule like the minimum size and the thickness of stiffener and the minimum cost have been searched by the optimizing algorithm. And the results have been compared with the non-optimizing results.
AL-Sadder, Samir Z.;Othman, Ra'ad A.;Shatnawi, Anis S.
Structural Engineering and Mechanics
/
제24권6호
/
pp.647-664
/
2006
In this study, an improved finite element formulation with a scheme of solution for the large deflection analysis of inextensible prismatic and nonprismatic slender beams is developed. For this purpose, a three-noded Lagrangian beam-element with two dependent degrees of freedom per node (i.e., the vertical displacement, y, and the actual slope, $dy/ds=sin{\theta}$, where s is the curved coordinate along the deflected beam) is used to derive the element stiffness matrix. The element stiffness matrix in the global xy-coordinate system is achieved by means of coordinate transformation of a highly nonlinear ($6{\times}6$) element matrix in the local sy-coordinate. Because of bending with large curvature, highly nonlinear expressions are developed within the global stiffness matrix. To achieve the solution after specifying the proper loading and boundary conditions, an iterative quasi-linearization technique with successive corrections are employed considering these nonlinear expressions to remain constant during all iterations of the solution. In order to verify the validity and the accuracy of this study, the vertical and the horizontal displacements of prismatic and nonprismatic beams subjected to various cases of loading and boundary conditions are evaluated and compared with analytic solutions and numerical results by available references and the results by ADINA, and excellent agreements were achieved. The main advantage of the present technique is that the solution is directly obtained, i.e., non-incremental approach, using few iterations (3 to 6 iterations) and without the need to split the stiffness matrix into elastic and geometric matrices.
Kim, Beom-geun;Khirul, Md Akhte;Cho, Dae-chul;Kwon, Sung-Hyun
한국환경과학회지
/
제28권10호
/
pp.851-861
/
2019
In this study, we performed a sediment elution experiment to evaluate water quality in terms of phosphorus, as influenced by the dissolved oxygen consumed by sediments. Three separate model column treatments, namely, raw, calcined, and sonicated oyster shell powders, were used in this experiment. Essential phosphorus fractions were examined to verify their roles in nutrient release from sediment based on correlation analyses. When treated with calcined or sonicated oyster shell powder, the sediment-water interface became "less anaerobic," thereby producing conditions conducive to partial oxidation and activities of aerobic bacteria. Sediment Oxygen Demand (SOD) was found to be closely correlated with the growth of algae, which confirmed an intermittent input of organic biomass at the sediment surface. SOD was positively correlated with exchangeable and loosely adsorbed phosphorus and organic phosphorus, owing to the accumulation of unbound algal biomass-derived phosphates in sediment, whereas it was negatively correlated with ferric iron-bound phosphorus or calcium fluorapatite-bound phosphorus, which were present in the form of "insoluble" complexes, thereby facilitating the free migration of sulfate-reducing bacteria or limiting the release from complexes, depending on applied local conditions. PCR-denaturing gradient gel electrophoresis revealed that iron-reducing bacteria were the dominant species in control and non-calcined oyster shell columns, whereas certain sulfur-oxidizing bacteria were identified in the column treated with calcined oyster powder.
This study presents an experimental investigation of the wear and oxidation of the bristles of a brush seal in a super-heated steam environment. We construct a model reflecting normal force and radial interference to predict the amount of wear. To monitor the volume loss of the bristle induced by the swirl phenomenon of the rotor, we measure the clearance between the rotor and the brush seal by using a non-contact 3-D device. We calculate the area by using the area-wise measurement method. Considering the obvious brush seal wear variables, we use two disks with different roughness($Ra=0.1{\mu}m$ and $100{\mu}m$) to determine the effect of roughness on wear. Considering an actual steam turbine, we utilize a steam generator and super-heater to generate a working fluid (0.95MPa, 523.15K) that has high kinetic energy. We observe the abrasion of the bristles in the hot steam environment through a scanning electron microscope image. This study also conducted energy dispersive X-ray (EDX) analysis for a qualitative evaluation of local chemistry. The results indicate that the wear and elimination of bristles occur on the disk with high roughness, and the weight increases due to oxidation. Furthermore these results, reveal that the bristle oxidation is accelerated more under super-heated steam conditions than under conditions without steam.
Purpose: This study aims to compare 119 emergency medical services (EMS) in South Korea and Japan to provide essential data for EMS improvement in South Korea. Methods: Recent data and regulations on firefighting and EMS in South Korea and Japan were analyzed and compared. Results: South Korea follows a centralized approach to EMS, whereas Japan operates with autonomous bodies that establish their own criteria. Japan considers more regional variables than South Korea. In South Korea, there are shortages in fire station deployment among the 119 emergency medical resources in certain regions, leading to significant regional disparities. South Korea has a larger population served by its 119 emergency medical resources with a higher workload and dispatch numbers than Japan. The percentage of non-transported patients among the total number of dispatches was higher in South Korea. Conclusion: Increasing the number of medical professionals and ambulances per population to the level of Japan to reflect local conditions and include various underlying variables such as daytime population, aging, and emergency dispatch conditions in the deployment of 119 emergency resources, and to reduce the deployment gap between regions, will contribute to improving the performance of the South Korea EMS system.
In this study, we optimized the FNLM algorithm through a simulation study and applied it to a phantom scanned by low-dose CT to evaluate whether the FNLM algorithm can be used to obtain improved image quality images. We optimized the FNLM algorithm with MASH phantom and FASH phantom, which the algorithm was applied with MATLAB, increasing the smoothing factor from 0.01 to 0.05 with increments of 0.001 and measuring COV, RMSE, and PSNR values of the phantoms. For both phantom, COV and RMSE decreased, and PSNR increased as the smoothing factor increased. Based on the above results, we optimized a smoothing factor value of 0.043 for the FNLM algorithm. Then we applied the optimized FNLM algorithm to low dose lung CT and lung CT under normal conditions. In both images, the COV decreased by 55.33 times and 5.08 times respectively, and we confirmed that the quality of the image of low dose CT applying the optimized FNLM algorithm was 5.08 times better than the image of lung CT under normal conditions. In conclusion, we found that the smoothing factor of 0.043 among the factors of the FNLM algorithm showed the best results and validated the performance by reducing the noise in the low-quality CT images due to low dose with the optimized FNLM algorithm.
최근 투명 디스플레이 및 유연 소자의 활용도가 증가함에 따라 우수한 유연성과 강성을 갖는 폴리머 소재 기판의 사용이 증가하고 있다. 그러나 폴리머는 열에 취약하여 공정 중 온도 및 열 제어가 필수적이다. 이러한 폴리머 기판 활용의 단점을 해결하기 위해 본 연구에서는 레이저 기반의 선택적 가공 기술에 적용할 수 있는 폴리머 기판 내 레이저 가공영역의 온도 측정 시스템을 제안한다. 레이저 가공 영역의 국부적인 온도 변화 측정을 통해 폴리머 기판의 공정 조건을 최적화하는 가능성을 제시한다. 이를 위해 플랑크 흑체 복사 원리를 기반으로 한 PDPT(Photodiode based Planck Thermometry)를 설계 및 제작하여 레이저가 입사되는 영역의 온도를 측정하였다. PDPT는 비파괴/비접촉식 온도측정 시스템으로, 레이저가 입사되는 국부적인 온도 상승을 실시간으로 측정할 수 있다. 해당 시스템을 활용하여 폴리머 기판의 레이저 가공 공정에서 발생하는 가공영역의 온도 변화를 관측하였다. 본 연구 결과, 제안된 레이저 기반 온도측정 기술은 레이저 가공 공정 중 실시간 온도 측정이 가능하며, 이를 통해 최적의 생산 조건을 확립할 가능성을 보여주고 있다. 또한, 해당 기술은 열 제어가 필수적인 미세 레이저 가공 및 3차원 프린팅과 같은 다양한 레이저 기반 공정에 적용될 수 있을 것으로 기대된다.
철근콘크리트 구조물의 내구성 및 안전성은 콘크리트의 균열 및 강도와 더불어 철근의 배근상태나 콘크리트 피복 두께에 크게 의존한다. 콘크리트 내에 매립되어 있는 철근 정보를 정확히 파악하는 방법엔 국부 파괴법과 비파괴 철근 탐사 시험이 있다. 일반적으로 부재 손상을 최소화하기 위해 비파괴 철근 탐사 시험을 통해 파악하며, 비파괴 철근 탐사 시험에는 전자파레이더법, 전자기유도법, 방사선법 등이 있다. 콘크리트의 함수율과 온도는 콘크리트의 전기적 특성인 유전율에 영향을 미쳐 비파괴 철근 탐사 시험 결과에 간섭을 방생시킨다. 따라서 본연구에서는 콘크리트의 표면수율과 온도에 따라 전자파레이더법과 전자기유도법이 받는 영향을 분석하였다. 장비와 기술의 발달로 원리와 상관없이 24℃ 시험체에서는 평균 오차율이 5% 이하로 나타났으며 특히 전자기유도법의 경우 매우 높은 정확성을 갖는 것을 확인하였다. 전자파레이더법은 습윤상태보다 건조상태에서 상대적으로 오차율이 작은 특성을 나타내었으며, 고온에서는 다소 높은 오차율이 나타났다. 탐사 대상의 온도가 낮고 건조한 경우 전자파레이더법을 적용하고, 탐사 대상이 습윤상태이거나 고온에서는 전자기유도법을 사용하여 오차를 감소시킬 수 있음이 확인되었다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.