• 한국지반환경공학회 논문집
• /
• 제12권11호
• /
• pp.65-70
• /
• 2011

모래지반의 액상화 발생 가능성 및 측방유동 평가 방법에 대한 연구는 많이 알려져 있다. 최근에는 비소성 실트의 액상화 발생 가능성에 대해서도 연구하고 있다. 그러나 비소성실트의 동적하중이 작용하는 동안과 그 이후의 거동에 대해서는 세계적으로도 다소 알려져 있을 뿐이다. 특히 비소성실트의 측방유동에 대한 평가방법에 대해서는 거의 알려져 있지 않다. 이에 본 연구에서는 비소성실트지반에서의 액상화 발생 가능성 및 측방유동량의 평가 방법을 제안하는 것을 목적으로 하였다. 연구방법은 정적 및 동적 시험을 수행할 수 있는 직접단순전단시험기를 이용하여 동적하중을 받은 비소성실트의 액상화 가능성을 평가하였으며, 그 후 정적 시험을 수행하여 잔류강도를 측정하였다. 이 시험결과 비소성실트는 유효응력이 완전이 소멸되는 것은 곤란하지만 액상화에 거의 가깝게 발생하는 것을 확인하였다. 특히, 전단응력의 증가에 따른 강도저하는 매우 현저한 것을 확인하였다. 이 시험결과를 이용하여 액상화 발생 가능성 및 측방유동량을 추정할 수 있는 방법을 제안하였다.

• Geomechanics and Engineering
• /
• 제7권6호
• /
• pp.589-612
• /
• 2014

This study includes determination of liquefaction potential in Erzincan city center. Erzincan Province is situated within first-degree earthquake zone on earthquake map of Turkey. In this context, the earthquake scenarios were produced using the empirical expressions. Liquefaction potential for different earthquake magnitudes (6.0, 6.5, 7.0) were determined. Liquefaction potential was investigated using Standard Penetration Test (SPT). Liquefaction potential analyses are determined in two steps: geotechnical investigations and calculations. In the first steps, boreholes were drilled to obtain disturbed and undisturbed soil samples and SPT values were obtained. Laboratory tests were made to identify geotechnical properties of soil samples. In the second step, liquefaction potential analyses were examined using two methods, namely Seed and Idriss (1971), Iwasaki et al. (1981). The liquefaction potential broadly classified into three categories, namely non-liquefiable, marginally liquefiable and liquefiable regions. Additionally, the liquefaction potential index classified into four categories, namely non-liquefiable, low, high and very high liquefiable regions. In order to liquefaction analysis complete within a short time, MATLAB program were prepared. Following the analyses, liquefaction potential index is investigated by Iwasaki et al. (1982) methods. At the final stage of this study, liquefaction potential maps and liquefaction potential index maps of the all study area by using IDW (inverse distance weighted) interpolation method in Geostatistical Analyst Module of ArcGIS 10.0 Software were prepared for different earthquake magnitudes and different depths. The results of soil liquefaction potential were evaluated in ArcGIS to map the distributions of drillings with liquefaction potential. The maps showed that there is a spatial variability in the results obtained which made it difficult to clearly separate between regional areas of high or low potential to liquefy. However, this study indicates that the presence of ground water and sandy-silty soils increases the liquefaction potential with the seismic features of the region.

• Geomechanics and Engineering
• /
• 제10권3호
• /
• pp.269-284
• /
• 2016

Simplified techniques based on in situ testing methods are commonly used to assess seismic liquefaction potential. Many of these simplified methods were developed by analyzing liquefaction case histories from which the liquefaction boundary (limit state) separating two categories (the occurrence or non-occurrence of liquefaction) is determined. As the liquefaction classification problem is highly nonlinear in nature, it is difficult to develop a comprehensive model using conventional modeling techniques that take into consideration all the independent variables, such as the seismic and soil properties. In this study, a modification of the Multivariate Adaptive Regression Splines (MARS) approach based on Logistic Regression (LR) LR_MARS is used to evaluate seismic liquefaction potential based on actual field records. Three different LR_MARS models were used to analyze three different field liquefaction databases and the results are compared with the neural network approaches. The developed spline functions and the limit state functions obtained reveal that the LR_MARS models can capture and describe the intrinsic, complex relationship between seismic parameters, soil parameters, and the liquefaction potential without having to make any assumptions about the underlying relationship between the various variables. Considering its computational efficiency, simplicity of interpretation, predictive accuracy, its data-driven and adaptive nature and its ability to map the interaction between variables, the use of LR_MARS model in assessing seismic liquefaction potential is promising.

• Geomechanics and Engineering
• /
• 제1권1호
• /
• pp.1-15
• /
• 2009

Many aspects of the behavior of sands are affected by the content of non-plastic fine particles and these various aspects should be included in a constitutive model for the soil behavior. The fines content affects maximum and minimum void ratios, compressibility, shear strength, and static liquefaction under undrained conditions. Twenty-eight undrained triaxial compression tests were performed on mixtures of sand and fine particles with fines contents of 0, 10, 20, 30, 50, 75, and 100% to study the effects of fines on void ratio, compressibility, and the occurrence of static liquefaction. The experiments were performed at low consolidation pressures at which liquefaction may occur in near-surface, natural deposits. The presence of fines creates a particle structure in the soil that is highly compressible, enhancing the potential for liquefaction, and the fines also alter the basic stress-strain and volume change behavior, which should be modeled to predict the occurrence of static liquefaction in the field. The void ratio at which liquefaction occurs for each sand/fines mixture was determined, and the variation of compressibility with void ratio was determined for each mixture. This allowed a relation to be determined between fines content, void ratio, compressibility, and the occurrence of static liquefaction. Such relations may vary from sand to sand, but the present results are believed to indicate the trend in such relations.

• 한국지반신소재학회논문집
• /
• 제23권2호
• /
• pp.29-42
• /
• 2024

2017년 포항지진으로 인해 액상화 현상에 의한 안벽구조물에 피해가 발생하였다. 액상화는 지진 시 과잉간극수압 증가로 인해 유효응력이 소실되어 발생하게 된다. 이에 따른 잔교식 안벽의 피해 발생 부분을 규명하며 액상화로 인한 피해를 분석하였다. 또한 개량지반의 경우 연암층과 강성차이로 인해 하부 Sand 층의 액상화 현상으로 인해 피해가 발생하여, 비액상화 지반으로 가정하고 추가적인 수치해석을 수행하였다. 과잉간극수압비의 증가에 영향을 주는 요인으로는 지반의 상대밀도 및 입력 지진가속도의 크기 등 여러 가지 원인이 있다. 따라서 본 연구는 입력가속도의 크기를 증가시켜 Case 1~3에 대해 수치해석을 수행하였고, 개량지반의 경우 하부 Sand층의 액상화 현상으로 인한 피해가 발생하여 비액상화지반으로 가정하여 분석을 수행하였다. 결과적으로, 개량지반은 하부 액상화지반이 있을 경우 추가적인 보강이 필요하며, 잔교식 안벽 말뚝의 수평변위가 약 2배 감소하는 현상이 나타났다.

• 한국지반공학회지:지반
• /
• 제6권3호
• /
• pp.41-52
• /
• 1990

To investigate the liquefaction potential of sands, a series of untrained cyclic triaxial compression tests is carried out on the samples of Ottawa, Joomoonjin, Hn river and Hongseung sands. The constitutive equations of sands are derived to explain the mechanical behavior of sands under cyclic stresses, and are applicable to liquefaction analysis. The following results are obtainded in this study. 1. Sands with the lower confining pressure or relative density are to be easily liquefied, and when the amplitude of cyclic stress are large, liquefaction takes places over only a few cycles. 2. Stress ratio, porewater pressure ratio and cyclic shear strains are to be good criteria to evaluate liquefaction potential of sands. 3. Hongseung sands which contains some silty clay shows higher dynamic properties than other sands. 4. The dynamic behaviors of undisturbed Hongseung sand are about same as those of dense sands. It is noted that undisturbed Hongseung sand shows higher liquefaction potential than the samples made by pluviation under same relative density, 5. The constitutive equations of soils under cyclic loads are developed based on the theory of elasto-plasticity, logarithmic stress-strain rela'tionship, non-associated flow rule and the concept of the boundary surface. The derived equations is applicable to predict the behavior of sands under cyclic loads and liquefaction potential with a higher accuracy. 6. Based on results of the study it may be concluded that cracks of the foundations and dislocation of the structures at Hongseung earthquakes(Oct. 7, 1978, Richter scald 5.2) are not brought by the liquefaction process.

• 한국지반환경공학회 논문집
• /
• 제8권1호
• /
• pp.41-47
• /
• 2007

최근 지진에 의한 액상화 피해를 입은 지역에서의 조사결과에 의하면 모래지반 뿐만 아니라 세립분을 함유한 흙 또는 비소성실트 지반에서도 액상화 피해사례가 보고되고 있으나, 지금까지 액상화는 느슨한 포화 모래지반에서 발생하는 것으로만 알려져 비소성실트의 액상화특성에 대하여 거의 알려져 있지 않다. 특히, 액상화강도는 전단탄성파속도와 밀접한 관계가 있어 현장에서는 PS검층 등을 이용하여 원위치에서 흙의 강성을 조사하며, 실내 실험에서는 정확한 흙의 강성을 조사하기 위하여 벤더엘레먼트를 이용한다. 본 연구에서는 단순전단시험기에 벤더엘레먼트를 장착하여 비소성실트의 강성을 조사하였으며 단순전단시험 결과와 비교하였다. 그 결과 벤더엘레먼트에 의한 비소성실트의 강성은 단순전단시험결과보다 약간 크게 나타나지만 그 차이는 적으며, 점토의 강성보다 작은 것을 알 수 있었다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.1512-1519
• /
• 2005

In this study, the potential for liquefaction in the Incheon international airport was calculated by appling the standard penetration test data and laboratory test data to the modified Seed & Idriss(2001) method. The analysis was performed on the non-plastic silty layer and silty sand layer which within the depth of 20m, below 20 of the standard penetration value(N), and the ground water level. Also, each set of data was mapped by using GIS(geographic information systems) and the factor of safety for the potential for liquefaction was obtained by overlapping those layers. As a result, it was found that there exist potential hazard zone for the liquefaction partially. So, the additional detailed assessments for those are thought to be necessary.

• Geomechanics and Engineering
• /
• 제17권2호
• /
• pp.145-156
• /
• 2019

Since behaviors of loose, dense, silty sands vary under seismic loading, understanding the liquefaction mechanism of sandy soils continues to be an important challenges of geotechnical earthquake engineering. In this study, 36 deformation controlled cyclic simple shear tests were performed and the liquefaction potential of the sands was investigated using three different relative densities (40, 55, 70%), four different effective stresses (25, 50, 100, 150 kPa) and three different shear strain amplitudes (2, 3.5, 5%) by using energy based approach. Experiments revealed the relationship between per unit volume dissipated energy with effective stress, relative density and shear strain. The dissipate energy per unit volume was much less affected by shear strain than effective stress and relative density. In other words, the dissipated energy is strongly dependent on relative density and effective stress. These results show that the dissipated energy per unit volume is very useful and may contain the non-uniform loading conditions of the earthquake spectrum. When multiple regression analysis is performed on experiment results, a relationship is proposed that gives liquefaction energy of sandy soils depending on relative density and effective stress parameters.

• Geomechanics and Engineering
• /
• 제4권2호
• /
• pp.121-134
• /
• 2012

The paper presents the results of identification, monotonous and cyclic triaxial tests on a potentially liquefiable soil from the Guadeloupe island. The material is a very soft clayey soil whose susceptibility to liquefaction is not clear when referring to index properties such as grain size distribution, plasticity, etc. The classifications found in the literature indicate that the material has rather a "clay-like" behaviour, i.e., is not very susceptible to liquefaction, but its properties are very close to the threshold values given by the authors. Cyclic triaxial tests carried out on the material under different conditions show that liquefaction is possible for a relatively important level of cyclic deviator or number of cycles. The second part of the paper is devoted to the study of the recovery of the soil after liquefaction and possibly reconsolidation. For the specimens tested without reconsolidation, that simulated the soil immediately after an earthquake, the recovery is nearly non-existent but the drop in pore pressure during extension results in a small available strength. On the contrary, after reconsolidation, the increase in strength of the liquefied specimens is quite large, compared to the initial state, but with unchanged failure envelopes.