• 한국전산구조공학회논문집
• /
• 제29권6호
• /
• pp.555-562
• /
• 2016

본 논문에서는 Nondominated sorting genetic algorithm-II(NSGA-II)를 이용한 Zipper를 가진 역V형 중심가새골조의 다목적 최적내진설계기법을 제시한다. 부재의 단면성능을 설계변수로 사용하는 제시된 최적화기법은 내진설계를 위해 부재의 강도조건, 구조물의 층간변위조건, 부재의 변형조건 등을 만족시키면서 구조물의 물량과 구조물의 최대 층간변위율을 동시에 최소화하는 문제로 정식화된다. 구조물의 물량과 최대 층간변위율을 최소화하는 이유는 구조물의 비용과 성능을 각각 최적화하기 위해서 이다. 선형 정적해석을 통해 구조물의 강도 및 층간변위 제약 조건을 검토하며, 비선형 정적해석을 통해 구조물의 변형 조건 및 내진성능을 평가한다. 제안된 기법을 검증하기 위해 3층과 6층 Zipper를 가진 역V형 중심가새골조 예제를 사용한다. 이를 통해 얻은 설계안을 초기 설계안과 비교분석하여 제안된 기법의 적용성을 확인한다.

• Steel and Composite Structures
• /
• 제24권2호
• /
• pp.227-237
• /
• 2017

This paper presents optimization of a long-span portal steel frame under dynamic wind loads using a surrogate-assisted evolutionary algorithm. Long-span portal steel frames are often used in low-rise industrial and commercial buildings. The structure needs be able to resist the wind loads, and at the same time it should be as light as possible in order to be cost-effective. In this work, numerical model of a portal steel frame is constructed using structural analysis program (SAP2000), with the web-heights at five locations of I-sections of the columns and rafters as the decision variables. In order to evaluate the performance of a given design under dynamic wind loading, the equivalent static wind load (ESWL) is obtained from a database of wind pressures measured in wind tunnel tests. A modified formulation of the problem compared to the one available in the literature is also presented, considering additional design constraints for practicality. Evolutionary algorithms (EA) are often used to solve such non-linear, black-box problems, but when each design evaluation is computationally expensive (e.g., in this case a SAP2000 simulation), the time taken for optimization using EAs becomes untenable. To overcome this challenge, we employ a surrogate-assisted evolutionary algorithm (SAEA) to expedite the convergence towards the optimum design. The presented SAEA uses multiple spatially distributed surrogate models to approximate the simulations more accurately in lieu of commonly used single global surrogate models. Through rigorous numerical experiments, improvements in results and time savings obtained using SAEA over EA are demonstrated.

• 한국소음진동공학회논문집
• /
• 제23권12호
• /
• pp.1035-1044
• /
• 2013

면내 하중을 지지하는 면재와 면외 하중을 지지하는 심재로 구성되는 샌드위치 패널 구조물은 높은 비강도와 비강성을 가지므로 경량화가 요구되는 대형 구조물에 자주 이용된다. 그러나, 이러한 구조물은 필연적으로 높은 하중에 대하여 유연성의 증가를 일으키게 되므로, 이에 대한 구조 안전성 분석이 이루어져야 한다. 이에 대해 실제 풍하중은 거스트 영향 등을 비롯한 비선형성을 가지는 요소들이 고려되어야 하며, 구조물의 안전성 분석을 위하여 입력 하중에 대해 보다 실제 물리현상에 근접하게 모사되어야 한다. 이에 이 연구에서는 유체-구조 연성해석 기법을 이용하여 대형 등격자-보강 패널 구조물에 대한 구조 안전성 분석이 수행되었다. 입력하중인 풍하중에 대하여 보다 실제적 모사를 위해 불규칙 변동 속도성분인 거스트 영향이 고려된 랜덤분포 풍하중에 대한 유동장을 생성하여 압력-변위 사상을 통하여 연성해석이 수행되었다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제22권4호
• /
• pp.42-51
• /
• 2018

해상풍력 지지구조물은 설치과정에서 수직도 오차가 발생하여 풍력발전기 전체 구조의 안전성이 저하될 수 있다. 따라서, 본 논문에서는 콘크리트 중력식 해상풍력 연결부에서 PS 앵커와 앵커체결구 그라우트를 사용하여 수직도를 조정할 수 있는 방안에 대한 연구를 수행하였다. 연결부는 5MW급 해상풍력 지지구조물에서 발생한 수직도 오차를 최대 $0.5^{\circ}$까지 보정하는 것을 목표로 하였다. 우선, 수직도 조정이 가능한 해상풍력 연결부에 대해 주요 부재별 설계안과 설계절차를 제안하고, 제주도 해상지역을 대상으로 설계 제원을 산출하였다. 그 후, 설계 제원에 대해 비선형 3차원 유한요소해석을 수행하여 설계안의 적정성을 검토하였다. 검토 결과, 하중 전달 메커니즘과 연결부 발생 응력 확인을 통해 제안 설계안은 $0.5^{\circ}$의 수직도 오차를 보정하여도 안전하다고 판단하였다.

• 대한토목학회논문집
• /
• 제7권2호
• /
• pp.29-36
• /
• 1987

초기균열을 갖는 대부분의 구초체는 부재크기가 증가함에 따라 강도가 저하한다. 이러한 현상을 크기효과(size effect)라고 한다. 유리, 금속, 콘크리트 동, 구조재료중에서 콘크리트는 비록 초기균열이 없더라도 이 size effect 현상을 보인다. 현존의 크기효과 법칙에 따르면 매우 큰 콘크리트 구조체는 거의 하중을 저하할 수 없다. 그러나 실제로는 초기 균열이 없는 경우 상당한 크기의 응력을 저항할 수 있다. 이러한 현상은 매우 큰 구조체와 작은 구조체는 강도기준의 적용이 합당하고, 그 중간 크기의 구조체는 비선형파괴역학의 적용이 합당함을 말한다. 이 논문에서는 비선형파괴역학에 근거하여 유도된 실험식에, 기존의 실험치를 이용하여 비선형회귀분석올 행하여 실험상수를 정함으로써 일축압축, 할열(splitting)인장 및 전단강도에 대한 실험식을 제시한다.

• Advances in Computational Design
• /
• 제4권4호
• /
• pp.327-342
• /
• 2019

Rehabilitation and retrofitting of structures designed in accordance to standard design codes is an essential practice in structural engineering and design. For steel structures, one of the challenges is to strengthen the panel zone as well as its analysis in moment-resisting frames. In this research, investigations were undertaken to analyze the influence of the panel zone in the response of structural frames through a computational approach using ETABS software. Moment-resisting frames of six stories were studied in supposition of real panel zone, different values of rigid zone factor, different thickness of double plates, and both double plates and rigid zone factor together. The frames were analyzed, designed and validated in accordance to Iranian steel building code. The results of drift values for six stories building models were plotted. After verifying and comparing the results, the findings showed that the rigidity lead to reduction in drifts of frames and also as a result, lower rigidity will be used for high rise building and higher rigidity will be used for low rise building. In frames with story drifts more than the permitted rate, where the frames are considered as the weaker panel zone area, the story drifts can be limited by strengthening the panel zone with double plates. It should be noted that higher thickness of double plates and higher rigidity of panel zone will result in enhancement of the non-linear deformation rates in beam elements. The resulting deformations of the panel zone due to this modification can have significant influence on the elastic and inelastic behavior of the frames.

• Structural Engineering and Mechanics
• /
• 제65권5호
• /
• pp.621-631
• /
• 2018

In this paper, an exact analytical solution is developed for the analysis of the post-buckling non-linear response of simply supported deformable symmetric composite beams. For this, a new theory of higher order shear deformation is used for the analysis of composite beams in post-buckling. Unlike any other shear deformation beam theories, the number of functions unknown in the present theory is only two as the Euler-Bernoulli beam theory, while three unknowns are needed in the case of the other beam theories. The theory presents a parabolic distribution of transverse shear stresses, which satisfies the nullity conditions on both sides of the beam without a shear correction factor. The shear effect has a significant contribution to buckling and post-buckling behaviour. The results of this analysis show that classical and first-order theories underestimate the amplitude of the buckling whereas all the theories considered in this study give results very close to the static response of post-buckling. The numerical results obtained with the novel theory are not only much more accurate than those obtained using the Euler-Bernoulli theory but are almost comparable to those obtained using higher order theories, Accuracy and effectiveness of the current theory.

• Steel and Composite Structures
• /
• 제24권3호
• /
• pp.287-296
• /
• 2017

The buckling capacity of a radially retractable hybrid grid shell in the closed position was investigated in this paper. The geometrically non-linear elastic buckling and elasto-plastic buckling analyses of the hybrid structure were carried out. A parametric study was done to investigate the effects rise-to-span ratio, beam section, area and pre-stress of cables, on the failure load. Also, the influence of the shape and scale of imperfections on the elasto-plastic buckling loads was discussed. The results show that the critical buckling load is reduced by taking account of material non-linearity. Furthermore, increasing the rise-to-span ratio or the cross-section area of steel beams notably improves the stability of the structure. However, the cross section area and pre-stress of cables pose negligible effect on the structural stability. It can also be found that the hybrid structure is highly sensitive to geometric imperfection which will considerably reduce the failure load. The proper shape and scale of the imperfection are also important.

• 한국결정성장학회:학술대회논문집
• /
• 한국결정성장학회 1996년도 제11차 KACG 학술발표회 Crystalline Particle Symposium (CPS)
• /
• pp.285-309
• /
• 1996

Non oxide ceramics such as nitrides of transition metals have shown significant potential for future economic impact, in diverse applications in ceramic, aerospace and electronic industries, as refractory products, abrasives and cutting tools, aircraft components, and semi-conductor substrates amid others. Combustion synthesis has become an attractive alternative to the conventional furnace technology to produce these materials cheaply, faster and at a higher level of purity. However he process os highly exothermic and manifests complex dynamics due to its strongly non-linear nature. In order to develop an understanding of this process and to study the effect of operational parameters on the final outcome, numerical modeling is necessary, which would generated essential knowledge to help scale-up the process. the model is based on a system of parabolic-hyperbolic partial differential equations representing the heat, mass and momentum conservation relations. The model also takes into account structural change due to sintering and volumetric expansion, and their effect on the transport properties of the system. The solutions of these equations exhibit steep moving spatial gradients in the form of reaction fronts, propagating in space with variable velocity, which gives rise to varying time scales. To cope with the possibility of extremely abrupt changes in the values of the solution over very short distances, adaptive mesh techniques can be applied to resolve the high activity regions by ordering grid points in appropriate places. To avoid a control volume formulation of the solution of partial differential equations, a simple orthogonal, adaptive-mesh technique is employed. This involves separate adaptation in the x and y directions. Through simple analysis and numerical examples, the adaptive mesh is shown to give significant increase in accuracy in the computations.

• Smart Structures and Systems
• /
• 제7권4호
• /
• pp.241-262
• /
• 2011

Cast iron pipe has been used as a water distribution technology in North America since the early nineteenth century. The first cast iron pipes were made of grey cast iron which was succeeded by ductile iron as a pipe material in the 1940s. These different iron alloys have significantly different microstructures which give rise to distinct mechanical properties. Insight into the non-destructive structural condition assessment of aging pipes can be advantageous in developing mitigation strategies for pipe failures. This paper examines the relationship between the small-strain and large-strain properties of exhumed cast iron water pipes. Nondestructive and destructive testing programs were performed on eight pipes varying in age from 40 to 130 years. The experimental program included microstructure evaluation and ultrasonic, tensile, and flexural testing. New applications of frequency domain analysis techniques including Fourier and wavelet transforms of ultrasonic pulse velocity measurements are presented. A low correlation between wave propagation and large-strain measurements was observed. However, the wave velocities were consistently different between ductile and grey cast iron pipes (14% to 18% difference); the ductile iron pipes showed the smaller variation in wave velocities. Thus, the variation of elastic properties for ductile iron was not enough to define a linear correlation because all the measurements were practically concentrated in single cluster of points. The cross-sectional areas of the specimens tested varied as a result of minor manufacturing defects and levels of corrosion. These variations affect the large strain testing results; but, surface defects have limited effect on wave velocities and may also contribute to the low correlations observed. Lamb waves are typically not considered in the evaluation of ultrasonic pulse velocity. However, Lamb waves were found to contribute significantly to the frequency content of the ultrasonic signals possibly resulting in the poor correlations observed. Therefore, correlations between wave velocities and large strain properties obtained using specimens manufactured in the laboratory must be used with caution in the condition assessment of aged water pipes especially for grey cast iron pipes.