• Journal of the Korean Institute of Landscape Architecture
• /
• v.23 no.1
• /
• pp.23-38
• /
• 1995

ELEECTRE is a less demanding and potentially Bffective multiattribute evaluation method for pre-editing proeedure. The method, however, was developed based on probabilistic mathematicsand its reliability has never'been emprieally tested. This article examined the reliability of ELECTRo under various conditions of linear and non-linear utility func- tions using a Monte-Carlo shnulation, and found the method eausea a considerably high rate of error. To enhance the reliability of ELECTRE, two ways of modi(ication - adjust- ment of threshold values of concordance and discordance matrices, and adjustment of the required nunlber of probably-dominant alternatives to eliminate a probably-dominated alternative - were suggested, and their effctiveness was also tesed by a Monte-Carlo simulation. The simulation result chows that these modifications cponsiderably improve the reliability of ELECTRE, and yet maintain a reasonably high level of efficiency. Through these modifications, ELECTRE can be used as an efficient and feliable pre-editing method. Ways to implement ELECTRE in the construction of plainning decision support systens were discussed. The impli(els combination of this method and other multiattribute evaluation methods will help to create more effective decision suport systems.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.12
• /
• pp.1333-1339
• /
• 2009

A MWR(Missile Warning Radar) of GVES(Ground Vehicle Equipment System) has to effectively decide the threat for a detected target. Linear Approximation Fitting(LAF) and Weighted Linear Approximation Fitting(WLAF) algorithm is proposed as algorithm for a threat decision method. The target is classified into a threat or non-threat using a boundary condition of the angular rate, and the boundary condition is determined using probability model simulation. This paper confirms the performance of proposed threat decision algorithm using measurement.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.2A
• /
• pp.195-202
• /
• 2007

A differential space-frequency block code - orthogonal frequency division multiplexing (SFBC-OFDM) scheme as a multiple-input multiple-output (MIMO) transmission technique for next-generation digital multimedia broadcasting (DMB) is proposed in this paper. A linear decoding method for differential SFBC, which performs comparably to the ML decoding method, is derived for the cases of two or four transmit antennas. A simple table lookup method is proposed to improve the efficiency of the encoding/decoding process of DSFBC for the case of non-constant modulus constellations. A DMB MIMO channel model, developed by extending the 3GPP MIMO model to fit DMB environments, is used to compare BER performances of differential space block code schemes for various channel environments. Simulation results show that the differential SFBC-16QAM scheme using either four transmit antennas with one receive antenna or two transmit antennas with two receive antennas achieves a performance gain of 12dB than that of the conventional DQPSK scheme, even with a data rate twice faster.

• Computers and Concrete
• /
• v.6 no.3
• /
• pp.187-202
• /
• 2009

This paper focuses on the flexural behavior of RC beams externally strengthened with Carbon Fiber Reinforced Polymers (CFRP) fabric. A non-linear finite element (FE) analysis strategy is proposed to support the beam flexural behavior experimental analysis. A development system (QUEBRA2D/FEMOOP programs) has been used to accomplish the numerical simulation. Appropriate constitutive models for concrete, rebars, CFRP and bond-slip interfaces have been implemented and adjusted to represent the composite system behavior. Interface and truss finite elements have been implemented (discrete and embedded approaches) for the numerical representation of rebars, interfaces and composites.

• Proceedings of the KIEE Conference
• /
• 1997.07f
• /
• pp.2193-2195
• /
• 1997

This paper describes a control system design for the transmission STATCON by applying a non-linear feedback. A mathematical model for the STATCON was derived by using a 3-phase equivalent circuit and its controller was designed by a numerical computation. The verification of newly designed controller was performed by EMTP simulation and scaled hardware model test. The test results show that the controller using non-linear feedback skim controls its reactive power properly without large transients.

• Journal of computational fluids engineering
• /
• v.13 no.1
• /
• pp.28-34
• /
• 2008

A particle method recognized as one of the gridless methods has been developed to investigate the nonlinear free-surface motions interacting to the structures. The method is more feasible and effective than convectional grid methods for solving the non-linear free-surface motion with complicated boundary shapes. The right-handed side of the governing equations for incompressible fluid, which includes gradient, viscous and external force terms, can be replaced by the particle interaction models. In the present study, the developed method is applied to the dam-broken problem on dried- and wet-floor and its adequacy will be discussed by the comparison with the experimental results.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.8
• /
• pp.1460-1466
• /
• 2011

This paper proposes the algorithm for discriminating faults from the variation due to the operation of non-linear components to prevent the mal-operation of protection relay in the distribution system. An IEEE 13 node test feeder is modeled to analyze the characteristics of the fault and each variation using EMTP-RV. Simulations with various operating conditions of transformers, non-linear loads, and unbalanced loads are performed using the test feeder model. Based on simulation results, the wavelet transform is adopted to analyze the current waveforms from the faults and variations to find out the differences between them and the algorithm for discriminating faults from the variation is proposed. The proposed algorithm is verified by using the current waveforms simulated in the KEPCO's distiribution system and IEEE 13 node test feeder.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.9
• /
• pp.1416-1423
• /
• 2017

Lane detection technology is one of the most important issues on car safety and self-driving capability of autonomous vehicle. This paper introduces an accurate lane detection scheme based on OCC(Optical Camera Communication) for moving vehicles. For lane detection of moving vehicles, the streetlights and the front camera of the vehicle were used for a transmitter and a receiver, respectively. Based on the angle information of multiple streetlights in a captured image, the distance from sidewalk can be calculated using non-linear regression analysis. Simulation results show that the proposed scheme shows robust performance of accurate lane detection.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.58 no.1
• /
• pp.38-43
• /
• 2009

Reactors are connected with capacitors to passive filter circuits for reducing harmonics caused by power conversion application. This passive filter frequently gets out of order by voltage and current stress. Especially filter reactor has too much voltage harmonics components, its trouble rate is higher than capacitor. In this paper, we analyzed voltage and current of reactor and capacitor used for passive filter by simulation and measurement. If reactor has a tolerance on variation of reactance value, series resonance frequency is different from originally filter design frequency and parallel resonance can be generated at the close point of the former. Because filter absorbs harmonic component of non-linear load, much of harmonic voltage has been impacted on reactor.

• Journal of Positioning, Navigation, and Timing
• /
• v.8 no.4
• /
• pp.193-200
• /
• 2019

The auto-encoder network which is a good candidate to handle the modeling of the signal strength attenuation is designed for denoising and compensating the distortion of the received data. It provides a non-linear mapping function by iteratively learning the encoder and the decoder. The encoder is the non-linear mapping function, and the decoder demands accurate data reconstruction from the representation generated by the encoder. In addition, the adaptive network width which supports the automatic generation of new hidden nodes and pruning of inconsequential nodes is also implemented in the proposed algorithm for increasing the efficiency of the algorithm. Simulation results show that the proposed method can improve the neural network training surface to achieve the highest possible accuracy of the signal modeling compared with the conventional modeling method.