• 한국산학기술학회논문지
• /
• 제8권2호
• /
• pp.185-188
• /
• 2007

최근 디젤 차량의 NOx와 PM의 동시 저감을 위해 EGR 밸브와 EGR 쿨러로 구성된 modulated EGR 시스템이 디젤엔진에 장착되고 있다. 본 연구에서는 modulated EGR 시스템의 성능 평가를 위한 test bench를 설계, 제작한 후 2.0 L 디젤엔진용 전자식 EGR 밸브를 시험하였다. 또한 전자식 EGR 밸브의 성능을 밸브양정의 거동, 밸브 개폐시의 응답성, 밸브 통과 유량을 통하여 평가하였다. PWM 신호의 듀티율에 따른 밸브 양정의 거동은 비선형적이었으며, 밸브 개방과 폐쇄의 경로가 상이한 히스테리시스 현상을 나타냈다. 밸브 개방시 응답성은 통상의 기준을 만족하여 적절하였다. 끝으로 밸브 통과 유량은 듀티율 $40{\sim}60%$에서 듀티율과 밸브 전후의 차압에 의해 결정되나, 듀티율 60%이상에서는 차압에만 의존하였다.

• Journal of Mechanical Science and Technology
• /
• 제15권7호
• /
• pp.1072-1076
• /
• 2001

A biomechanical study was conducted in this study to investigate if in-line skating wrist guards can effectively reduce the impact forces so as to protect the wrist from fracture. The forearm specimens with and without wrist guards were dropped using a specially designed sled to simulate the impact on the wrist while falling. A force plate was used to measure the total impact force on the dropping weight whereas a load cell was attached to the proximal end of the specimen and used to quantify the impact transmitted through the wrist joint. From the non-destructive tests, mean peak force measured from a force plate showed no difference between the guarded and unguarded groups whereas mean impulse of the guarded group was significantly greater than that of the unguarded group (p<0.01). Comparing the peak force and impulse measured from the load cell, the peak force of the guarded group was significantly less than that of the unguarded group (p<0.001), while the impulse values were similar. When the specimens were dropped from a higher position (2.5ft ve. 1ft), all unguarded specimens had severe wrist fractures whereas fracture was found in three out of 5 guarded specimens. Comparison of mean peak forces and impulses showed as significant difference between the guarded and unguarded groups only in the mean impulse measured from the force plate. These results suggest that the wrist guard may protect the wrist by attenuating the peak force transmitted to radius and ulnar although it may not be effective when the wrist is subjected to an impact sufficiently large to cause fractures.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2009년도 하계학술발표대회 논문집
• /
• pp.645-649
• /
• 2009

Liquid desiccant cooling technology can supply cooling by using waste heat and solar heat which are hard to use effectively. For compact and efficient design of a dehumidifier, it is important to sustain sufficient heat and mass transfer surface area for water vapor diffusion from air to liquid desiccant on heat exchanger. In this study, the plate type heat exchanger is adopted which has extended surface, and hydrophilic coating and porous layer coating are adopted to enhance surface wettedness. PP(polypropylene) plate is coated by porous layer and PET(polyethylene terephthalate) non-woven fabric is coated by hydrophilic polymer. These coated surfaces have porous structure, so that falling liquid film spreads widely on the coated surface foaming thin liquid film by capillary force. The temperature of liquid desiccant increases during dehumidification process by latent heat absorption, which leads to loss of dehumidification capacity. Liquid desiccant is cooled by cooling water flowing in plate heat exchanger. On the plate side, the liquid desiccant can be cooled by internal cooling. However the liquid desiccant on extended surface should be moved and cooled at heat exchanger surface. Optimal mixing and distribution of liquid desiccant between extended surface and plate heat exchanger surface is essential design parameter. The experiment has been conducted to verify effective surface treatment and distribution characteristics by measuring wall side flow rate and visualization test. It is observed that hydrophilic and porous layer coating have excellent wettedness, and the distribution can be regulated by adopting holes on extended surface.

• 대한정형도수물리치료학회지
• /
• 제17권2호
• /
• pp.19-24
• /
• 2011

Background: The elderly are likely to fall due to physical and mental atrophies, and experiencing falls may result in fear of falls and lack of self-confidence, which also leads to hesitation to physical activities and changes in walk and balance, the major variables in independent daily life. Methods: In three senior citizen centers located in D city, 22 elderly women aged 65 or older were chosen, and they filled in the questionnaire which included their agreement to voluntarily participate in the survey and medical histories. As to whether they had falls experience, the medical history items in the questionnaire asked them if they had falling down or falls once a year, twice for the three years. The objects were divided to NFE (non-falls experience) and FE (falls experience). Results: 1. As to walking abilities, significant difference was found between NFE and FE regarding walk width, stepping with two feet, and stride length while there was no significant different in terms of cadence. 2. As to balancing abilities, was significant difference between NFE and FE in terms of the physical body center area. As to the sit-to-stand, tandom gait test, no significant difference was found, and neither in the timed up and go test. Conclusions: The elderly with falls experience has inferior walking and balancing abilities to those without falls experience, and thus they are more exposed to the risks of falls.

• 산업경영시스템학회지
• /
• 제38권3호
• /
• pp.149-158
• /
• 2015

The purpose of this paper is to investigate the determinants of new product diffusion. We seek to document and explain systematic features of product diffusion. In this essay, we examine the well-documented empirical regularity that the speed of diffusion has accelerated during the twentieth century. The empirical results show that the main source of acceleration are faster declines in prices. Faster price declines make the product affordable to more consumers within a given period of time. Based on theories of intertemporal price discrimination and learning-by-doing, the association between the speed of adoption and the speed of price decline was explained. Faster price declines are attributed to several product characteristics as well as changes in income distribution. Above all, the introduction of consumer electronic products in more recent years can be regarded as the most important factor in accelerating price declines. Consumer electronic products are technologically different from non-electronic goods, in that semiconductors are important components. As the price of semiconductors has dropped rapidly, the falling production costs can be rapidly incorporated to the price of consumer electronic goods. Furthermore, most of the recently introduced consumer electronic products have network externalities, and many products with network externalities require complementary products. A complementary product becomes more readily or cheaply available as more people have the main product. One major difference between previous studies and this study is that the former focuses only on the factors that operate directly on the speed of adoption, while this study incorporated factors that work through price changes as well as the factors that work directly on the speed of adoption.

• 설비공학논문집
• /
• 제2권1호
• /
• pp.37-48
• /
• 1990

The drag and heat transfer reduction phenomena and degradation effects of drag reducing polymer solutions which are known as the viscoelastic fluids are investigated experimentally for the turbulent circular tube flows. Two stainless steel tubes are used for the experimental flow loops. Aqueous solutions of Polyacrylamide Separan AP-273 with concentrations from 300 to 1000 wppm are used as working fluids. Flow loops are set up to measure the friction factors and heat transfer coefficients of test tubes in the once-through system and the recirculating flow system. Test tubes are heated by power supply directly to apply constant heat flux boundary conditions on the wall. Capillary tube viscometer and falling ball viscometer are used to measure the viscous characteristics of fluids and the characteristic relaxation time of a fluid is determined by the Powell-Eyring model. The order of magnidude of the thermal entrance length of a drag reducing polymer solution is close to the order of magnitude of the laminar entrance length of Newtonian fluids. Dimensionless heat transfer coefficients of the viscoelastic non-Newtonian fluids may be represented as a function of flow behavior index n and newly defined viscoelastic Graetz number. As degradation continues viscosity and the characteristic relaxation time of the testing fluids decrease and heat transfer coefficients increase. The characteristic relaxation time is used to define the Weissenberg number and variations of friction factors and heat transfer coefficients due to degradation are presented in terms of the Weissenberg number.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제33권5호
• /
• pp.530-534
• /
• 2007

Nasal fractures are the most common type of facial fractures. Nowdays computed tomography is found to be very helpful in diagnosing nasal fracture, especially in findings the nasal septal fractures. From August 2004 to July 2005, 36 cases of nasal fracture were admited and reviewed to oral and maxillofacial surgery of Ulsan University Hospital, not including other facial bone fracture. Out of 223 cases of facial bone fractures, we treated 47 cases of nasal fractures. We reviewed and examined the 36 patients of nasal fractures 2months postoperative. The results were 28cases of male and 8cases of female. The highest age frequency was in the fourth decades group. The most frequent causes of injury were falling down and fist trauma. The 25(69%) patients were found to have septal fractures, after computed tomography findings. The treatment methods of nasal fracture were closed reduction(13cases), open reduction(20cases), ORIF(1case), non operation(2cases). Complications of nasal deformity were found in 2patients. Septoplasty was performed on 21 patients. Septal fractures in combination with nasal fracture are usually unrecognized and untreated at the time of injury, usually ended in nasal deformities. It is important to find out the exact type of nasal fractures. We will report the results of treatment of nasal fractures with a literature review.

• Journal of Preventive Medicine and Public Health
• /
• 제37권3호
• /
• pp.274-281
• /
• 2004

Objectives : This study was performed to investigate the injury rates and risk factors for preschool children in Daegu city and Kyungpook province. Method : A questionnaire survey about medically attended injuries during the preschool period was performed in nine primary schools located in Daegu city, Pohang city and Goryung County. The overall injury rate was estimated using person-year. The causes and patterns of the injuries, and their risk factors were examined. Result : A total of 469 medically attended injuries were reported in 330 of the 959 study subjects during the preschool period. The overall annual injury rate was 7.5 per 100 children. The injury rate increased sharply during the period from infant (2.4) to 1 year of age (7.5), and the peak injury rate (9.2) was reported for 5 year olds. The most common causes of injuries were falling (36.0%), followed by being struck by an object (23.7%), and traffic accidents (14.1%). Among the traffic accidents, 72.8% occurred while playing on the road, riding a bicycle or roller-skating. A proportional hazard model showed that males (hazard ratio=1.49, p<0.001 compared with female) and the mother's higher education level (hazard ratio of college or higher= 1.51, p=0.013; high school=1.32, p=0.085 compared with those of middle school or lower) were significant risk factors of childhood injury. Conclusion : The results of this study suggested that efforts for children's safety should be made, especially from the toddler stage, and in male children. To develop a more specific childhood injury prevention program, a surveillance system for injuries should be established. Further study of the relationship between mother's occupation and injury rates is also needed.

• Biomolecules & Therapeutics
• /
• 제25권2호
• /
• pp.105-111
• /
• 2017

It has been known that RA, one of major constituents of Perilla frutescens which has been used as a traditional folk remedy for sedation in oriental countries, shows the anxiolytic-like and sedative effects. This study was performed to know whether RA may enhance pentobarbital-induced sleep through ${\gamma}-aminobutyric$ acid $(GABA)_A-ergic$ systems in rodents. RA (0.5, 1.0 and 2.0 mg/kg, p.o.) reduced the locomotor activity in mice. RA decreased sleep latency and increased the total sleep time in pentobarbital (42 mg/kg, i.p.)-induced sleeping mice. RA also increased sleeping time and number of falling sleep mice after treatment with sub-hypnotic pentobarbital (28 mg/kg, i.p.). In electroencephalogram (EEG) recording, RA (2.0 mg/kg) not only decreased the counts of sleep/wake cycles and REM sleep, but also increased the total and NREM sleep in rats. The power density of NREM sleep showed the increase in ${\delta}-waves$ and the decrease in ${\alpha}-waves$. On the other hand, RA (0.1, 1.0 and $10{\mu}g/ml$) increased intracellular $Cl^-$ influx in the primary cultured hypothalamic cells of rats. RA (p.o.) increased the protein expression of glutamic acid decarboxylase ($GAD_{65/67}$) and $GABA_A$ receptors subunits except ${\beta}1$ subunit. In conclusion, RA augmented pentobarbital-induced sleeping behaviors through $GABA_A-ergic$ transmission. Thus, it is suggested that RA may be useful for the treatment of insomnia.

• Safety and Health at Work
• /
• 제12권4호
• /
• pp.511-516
• /
• 2021

Background: Difficulties in walking and balance are risk factors for falling. This study aimed to predict dynamic balance based on demographic information and anthropometric dimensions in construction workers. Methods: This descriptive-analytical study was conducted on 114 construction workers in 2020. First, the construction workers were asked to complete the demographic questionnaire determined in order to be included in the study. Then anthropometric dimensions were measured. The dynamic balance of participants was also assessed using the Y Balance test kit. Dynamic balance prediction was performed based on demographic information and anthropometric dimensions using multiple linear regression with SPSS software version 25. Results: The highest average normalized reach distances of YBT were in the anterior direction and were 92.23 ± 12.43% and 92.28 ± 9.26% for right and left foot, respectively. Both maximal and average normalized composite reach in the YBT in each leg were negatively correlated with leg length and navicular drop and positively correlated with the ratio of sitting height to leg length. In addition, multiple linear regressions showed that age, navicular drop, leg length, and foot surface could predict 23% of the variance in YBT average normalized composite reach of the right leg, and age, navicular drop, and leg length could predict 21% of that in the left leg among construction workers. Conclusion: Approximately one-fifth of the variability in the normalized composite reach of dynamic balance reach among construction workers using method YBT can be predicted by variables age, navicular drop, leg length, and foot surface.