• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.04a
• /
• pp.282-287
• /
• 2009

In this paper, 3-stage centrifugal turbo compressor was measured and analyzed numerical simulation for find noise source and was reduced noise with changing designs. For this purpose, it was measured noise level and was analyzed noise frequency at each stage. In order to Find where is noise source, the study was investigated about structure borne noise by using modal analysis and also was checked sound radiation and leakage of noise at inlet and outlet by result of sound intensity. In order to reduce of noise, sound insulation rings were maded and were adhered at joint and noise reduction effects were verified by measurement and numerical simulation. From the analysis results of leakage of noise, this study presented new joint designs, also it was verified by result of numerical simulation.

• Journal of Environmental Impact Assessment
• /
• v.26 no.1
• /
• pp.11-26
• /
• 2017

Approximate empirical equations obtained by measuring overall noise levels at different distances have been used to evaluate environmental influence of the railway noise though the accurate prediction of noise levels is important. In this paper, a noise prediction model considering the frequency characteristics of noise sources and propagation was suggested to improve the accuracy of noise prediction. The railway noise source was assorted into track, wheel, traction and aerodynamic components and they were characterized with the source strength and speed coefficient at each octave-band frequency. Correction terms for the acoustic roughness and the track/bridge condition were introduced. The sound attenuation from a source to a receiver was calculated taking account of the geometrical divergence, atmospheric absorption, ground effect, diffraction at obstacles and directivity of source by applying ISO 9613-2. For obtaining the source strength and speed coefficients, the results of rolling noise model, numerical analysis and measurements of pass-by noise were analyzed. We compared the predicted and measured noise levels in various vehicles and tracks, and verified the accuracy of the present model. It is found that the present model gives less error than the conventional one, so that it can be applied to make the accurate prediction of railway noise effect and establish its countermeasures efficiently.

• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.1441-1447
• /
• 2008

This research studies the effects of community noise around railway, noise from the inside/outside noise of the High-Speed EMU. First study part of this year is research of the noise source. The modeling methodology for prediction of noise level including the frequency property, velocity dependence, sound pressure of noise source is investigate. Second part is research on the sound transmission loss. An exclusive program which could analyze the sound transmission loss of the floor, the sides(mirror), insulator in High-Speed EMU has to be developed. Third part is research on the train inside/outside and Prediction for community Noise. In order to predict the noise when the High-Speed EMU is traveling at the outside and along tunnels, the result of the research can be derived by evaluating the effect of the noise on the upper/middle parts of the carriage and on the railroad way round about with using the program.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.10a
• /
• pp.271-277
• /
• 2003

Recently as the environmental noise getting influential social problem, it is the fact that the demand on noise reduction increases with the advance of the standard of living. Therefore increasing the interest on the noise in common, it is eagerly demanded that the endeavour for reducing the noise of the rotating machinery, especially the machinery related a flowing including the household electric products, which is pointed out the primary noise source in environment. As proceeding study for fan noise, theory of fan noise property is arranged and this control method is shown. Blade passage noise of total noise spectrum. Thus in the aspect of noise reduction, noise source and identification of noise radiation characteristics of axial flow fan are demanded in detail. The sound source is analyzed by using sound pressure and sound intensity. In that time, synchronization of axial flow fan using optical sensor is executed, and to identify the location of exact noise source in the fan profile determination of recording time is proposed. In the rotating of tan, it is explained that the location of noise source exists in and by the directivity, the noise radiation pattern of axial flow fan is determined and the flow of sound is visualized in the figure of contour mapping.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.6
• /
• pp.550-555
• /
• 2012

Among the various elements affecting a customer's evaluation of automobile quality, buzz, squeak and rattle(BSR) have been considered to be major factors. In most vehicle manufacturers, the BSR problems are solved by find-fix method with the vehicle road test, mainly due to various excitation sources, complex generation mechanism and subjective response. To systematically tackle the BSR problems in early stage of the vehicle development cycle, these difficulties should be resolved. The aim of the present paper is to characterize the sound quality property of BSR noise that can be used to assess the subjective responses to BSR. The four sound metrics from Zwicker's sound quality parameter are computed for the signals recorded for eight BSR noise source regions localized by using the acoustic-field visualized results. Then, the jury test of BSR noise are performed. On the basis of the computed sound metrics and jury test result is evaluated to represent the harshness of BSR noise. It is expected that the developed BSR measuring system and sound quality properties can be used to reduce the automotive interior BSR noise in terms of subjective levels as well as objective levels.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.3
• /
• pp.251-260
• /
• 2009

In this paper, we studied on an attenuation effect of automobile exhaust noise according to the direction of canceling speaker in ANC system. Automobile exhaust noise was recorded at 800 rpm, 3500 rpm and 5000 rpm of a diesel engine. Directions of canceling speaker can be set to $30^{\circ}$, $90^{\circ}$ and $150^{\circ}$ against the primary noise flow by acrylic ducts to be made for the experimentation. DSP board with TMS320C6416 chip of Texas Instrument Co. used to control the ANC system. The algorithm of this ANC system applied the Filtered-x-LMS algorithm that is modified to compensate for a property of DSP input signal and the secondary-path effect. As an experiment result, the direction of canceling speaker was proved to influence the reduction effect of noise. The $150^{\circ}$ duct in the attenuation effect of noise showed a better result than the $90^{\circ}$ or $30^{\circ}$ duct.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.21 no.1
• /
• pp.7-12
• /
• 1984

In this paper, the authors applied the method of hydrogen chloride gettering oxidation to fabricate the low noise bipolar transistor. The results of measurements of the effect of guttering on the variation of flicker noise spectral intensity for variable HCI concentrations indicate that flicker noise in bipolar than-sistor is dependent on the surface condition and that the gettering in a mixture of 2% HCI in oxidation produced the optimal results in the fabrication of the low noise device. In addition, it was also noted that the PSG layer formed by the emitter source (phosphorus) did not have so much guttering effect as in the process with HCl getterinng.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.5 no.3
• /
• pp.392-403
• /
• 2013

For the analysis of radiating noise problems in medium-to-high frequency ranges, the Energy Flow Boundary Element Method (EFBEM) was developed. EFBEM is the analysis technique that applies the Boundary Element Method (BEM) to Energy Flow Analysis (EFA). The fundamental solutions representing spherical wave property for radiating noise problems in open field and considering the free surface effect in underwater are developed. Also the directivity factor is developed to express wave's directivity patterns in medium-to-high frequency ranges. Indirect EFBEM by using fundamental solutions and fictitious source was applied to open field and underwater noise problems successfully. Through numerical applications, the acoustic energy density distributions due to vibration of a simple plate model and a sphere model were compared with those of commercial code, and the comparison showed good agreement in the level and pattern of the energy density distributions.

• Journal of the Korean Institute of Navigation
• /
• v.20 no.4
• /
• pp.71-79
• /
• 1996

When navigating in or near an area of restricted visibility, it is necessary to be heard the whistle, bell and/or the siren of lighthouses or ships at times. Even though we can get the brief informations about the property of sound, the direction and range of a sound radiator, it is not enough to get the accurate informations for decision making. Generally the audio frequency is known as 16~20, 000Hz, but the earshot is shorten and discrimination of sound is more difficult when there is some noise. The sound pressure is 60dB at the moment when human speaks 1 meter away. Usually the noise pressures are 40dB in a silent room and 60dB on the quiet street, respectively. It this study, the basic algorithm and a method of signal processing are suggested to trace the direction and range of the source radiator using the signals received through not a physical sense but the microphone sensors.

• The Journal of the Acoustical Society of Korea
• /
• v.24 no.3E
• /
• pp.87-89
• /
• 2005

The acoustical sources of intake and exhaust systems in fluid machines are often characterized by the source impedance and strength using linear frequency-domain modeling. In the case of the sources which are nonlinear and time-variant, however, the source parameters were sometimes incorrectly obtained. In this paper, the source model and direct measurement technique are modified in order to evaluate the effect due to nonlinear and periodically time-varying source character as well as the linear property of the reflectivity of in-duct fluid machine source. With a priori known kinematical information of the source, the types of nonlinear time-variant terms can be presumed by a simple physical model, in which there is practically no restriction on the form of the model. The concept of source impedance can be extendable by introducing the linear frequency response function for each nonlinear or time-variant input. Extending the conventional method and adapting the reverse MISO technique, it is possible to develop a direct method that can deal with the nonlinear time-variant source parameters. The proposed direct method has a novel feature that there is no restriction on the probability or spectral natures of the excited sound pressure data. The present method is verified by the simulated measurements for simplified fluid machines. It is thought that the proposed method would be useful in predicting the insertion loss or the radiated sound level from intake or exhaust systems.