• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.279-280
• /
• 2008

Accelerated aging tests were conducted under laboratory conditions on two generator stator bars. Electrical stress is applied in No. 1 model stator bar. Electrical and thermal stresses are applied in No. 2 model stator bar. As aging times increased from 0 to 4780h, diagnostic tests were performed on No. 1 and No. 2 model stator bars. Diagnostic tests included AC current, dissipation factor(tan$\delta$) and partial discharge magnitude. The ${\Delta}tan{\delta}$ and $\Deta$I of No. 1 and No. 2 model stator bars increased with increased in aging time.

• Proceedings of the KIEE Conference
• /
• 2002.11d
• /
• pp.200-203
• /
• 2002

This paper presents Continuous-current mode of $S^4$-PFC(Single-Stage Single-switch Power Factor Correction) converter. Proposed converter operates in the continueous current mode(CCM) at full load and discontinuous current mode(DCM) at light load. So, characteristic of proposed converter is no bus voltage stress and Zero Voltage Switching(ZVS) using resonant auxiliary circuit. And. This paper presents characteristic of $S^4$-PFC converter and effect of circuit parameter of proposed converter through the input inductor, PFC capacitor's variation. All of these theory and characteristic verified through the experiment with a 72W(12V, 6A), $90^{kHz}$ prototype converter.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.2B no.4
• /
• pp.183-190
• /
• 2002

This paper presents an improved Zero Voltage/Zero Current Switching (ZVZCS) commutation cell with minimum additional components, which provides soft switching at both turn-on and turn-off of main and auxiliary switches as well as diodes in a PWM DC/DC converter. The proposed soft-switching technique is suitable for not only minority, but also majority carrier semiconductor devices. The auxiliary switch of the proposed ZVZCS commutation cell is in parallel with the main switch, and therefore, the main switch and the diode are free of currentstress. The operation principles of the proposed ZVZCS commutation cell are theoretically analyzed using the PWM boost converter topology as an example. The validity of the PWM boost converter topology with the proposed ZVZCS commutation cell is verified through theoretical analysis, simulation and experimental results.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.26 no.6
• /
• pp.538-548
• /
• 1993

In order to estimate the influence of wind stress in the southwestern coastal waters of the Japan Sea, the wind stress was estimated from the shipboard wind data of the Fisheries Research and Development Agency along the serial observation lines and Buoy No. 6 of the Japan Meteorological Agency. 5,100 wind data are used to construct a data set of monthly mean wind stress during 10 years from 1978 to 1987. The negative values of the mean zonal wind stress curl at Ulleung Basin in the study area seem to be responsible for the formation of the warm core. The volume transport of the East Korea Warm Current are estimated quantitatively by the variations of the Ekman transport associated with the reversing direction of the monsoon. And the distribution of the warm core is explained by the simple three layer model.

• Korean Journal of Health Education and Promotion
• /
• v.21 no.3
• /
• pp.195-211
• /
• 2004

Stress is a primary health promotion issue in worksite research because psychological distress is closely related not only to workers' health status but also to their job performance. This study identified the significant health behaviors affecting workers' job-related stress in Korean manufacturing industry with the national survey data conducted by the Korean Occupational Safety and Health Agency in 2003. A total of 7,818 factory workers in 1,562 manufacturing companies participated in the Korean nation-wide occupational health survey and 3,390 workers answered that they had any stressors in their workplace among the 7,818 workers finally participated in the analysis. Participants were selected by the stratified proportional sampling process by manufacturing industry classification, company size, and company locations (8 metropolitan and 8 non-metropolitan regions) in Korea. Trained interviewers visited the target companies and interviewed the factory workers randomly selected in each company. Smoking, drinking, weight control, exercise, sleeping, break time at work, and perceived fatigue were included in the health behavior construct. Stress symptoms was consisted of physical and psychological stress with 8 items. All survey responses were anonymously coded into the SPSS statistical program and testified using stepwise multiple regression analysis. Male workers were 73.5% and the 30s were 40.0% among the age groups. The married and the high school graduate were majority with 52.1% and 61.8% each. Current smokers were 44.7% and More than 50% of the participants drank alcohol sometimes. No exercise group was 59.3% and the participants who dissatisfied with their daily sleeping hours were 43.5%. In t-test and analysis of variance, the significant general characteristics associated with physical and psychological job stress were young age (p<0.001), single marital status (p<0.001), and short working period at the present company (p<0.001). The health behaviors related to physical job stress were current smoking, weight change during the past one year (p<0.001), weight control effort (p<0.001), exercise (p<0.001), daily sleeping dissatisfaction (p<0.001), break time, and perceived fatigue (p<0.001). All 10 health behavior factors were significantly associated with psychological job stress (p<0.05). Weight change, weight control effort, exercise, daily sleeping dissatisfaction, little break at work, and high perceived fatigue were significant factors affecting job stress. Daily sleeping dissatisfaction, little break at work, little exercise, weight change for the past one year and young age were selected as the significant health behavior and general factors affecting physical job stress symptoms in stepwise multiple regression analysis. The five factors explained 18.9% of the physical stress score variance. Six factors were selected as the significant health behaviors affecting psychological job stress: daily sleeping dissatisfaction, little exercise, frequent drinking alcohol, high perceived fatigue, little break at work, and little weight control effort. The six factors explained 10.6% of the psychological stress score variance.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.5
• /
• pp.729-736
• /
• 1990

Oxide (RTO), nitrided-oxide(NO), and reoxidized-nitrided-oxide(ONO) films were formed by sequential rapid thermal processing. The film composition was investigated by Auger electron spectroscopy(AES). The Si/SiO2 interface and SiO2 surface are nitrided more preferentially than SiO2 bulk. When the NO is reoxidized, [N](atomic concentration of N) in the NO film decreased` especially, the decrease of [N] at the surface is considerable. The weaker the nitridation condition is, the larger the increase of thickness is as the reoxidation proceeds. The elelctrical characteristics of RTO, NO, and ONO films were evaluated by 1-V, high frequency (1 MHz) C-V, and high frequency C-V after constant current stress. The ONO film-which has 8 nm thick initial oxide, nitrided in NH3 at 950\ulcorner for 60 s, reoxidized in O2 at 1100\ulcorner for 60 s-shows good electrical characteristics such as higher electrical breakdown voltage and less variation of flat band voltage under high electric field than RTO, and NO films.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.4A
• /
• pp.383-389
• /
• 2010

The concrete structural design provisions in Korea are based on ultimate strength design. Up to service load stage, it is assumed a linear stress-strain relation, but there is no stress-strain relationship for a concrete material from service load stage to limat state. According to the current provisions, an independent method is provided for the each calculation of deflection and crack width. In EC2 provisions based on limit state design, however, a stress-strain relationship of concrete is provided. Thereby, it is able to calculate a strength as well as a deflection directly from concrete stress-strain relationship. In this paper the moment-curvature relationship is directly calculated from a material law using equilibrium and compatibility conditions. Then strength and deflection are formulated. These results are compared with the values from the current provisions in Korea. From the results, the deflection based on a moment-curvature relationship is well agreed with experimental results and it is appeared that the deflection after the yielding of steel is also possible.

• Journal of Surface Science and Engineering
• /
• v.38 no.1
• /
• pp.14-20
• /
• 2005

The control of internal stress is extremely important in electroforming because of the deliberately low adhesion between the electro form and the mandrel. Excessive tensile or compressive stress can cause distortion, separation problem, curling, peeling or separation of electroform prematurely from the mandrel, buckling and blistering. Nickel sulfamate bath has been widely used in electroforming because of its low internal stress and moderate hardness. In this study, real-time stress sensor has been used for stress control in chloride-free nickel sulfamate bath for 400 mm x 300 mm x 500 ㎛ nickel electroform. It was found that compressive stress found at low current density indicated the contamination of electrolyte, which is very useful in procuring buckling and peeling of electroform. No compressive stress is allowed for plate electroform. The real-time stress can also be used for accurate stress control of nickel electroform. The tensile stress was found to be increased slightly with increase in nickel electroform thickness, i.e., from initial 1.47 ksi to 2.02 ksi at 320 ㎛.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.6
• /
• pp.63-69
• /
• 2011

This study analyzes stress, fatigue and vibration on main rotor and body of helicopter. The maximum stress is shown on adjoint part between body and main rotor at the lower position of main rotor. As the maximum displacement amplitude is happened at 4000Hz, there is no resonance and the state of helicopter becomes safe at hovering without the abnormal air current and the disabled rotor. Among the cases of nonuniform fatigue loads, 'SAE bracket history' with the severest change of load becomes most unstable but 'Sample history' becomes most stable. In case of 'Sample History' with the average stress of 0MPa to $-10^5MPa$ and the amplitude stress of 0MPa to $8.539{\times}10^5MPa$, the possibility of maximum damage becomes 3%. This stress state can be shown with 5 times more than the damage possibility of 'SAE bracket history' or 'SAE transmission'. The structural result of this study by using the analysis of vibration and fatigue can be effectively utilized for safe and durable design of helicopter.

• Transactions of Materials Processing
• /
• v.24 no.3
• /
• pp.212-217
• /
• 2015

SmartCrown is a system to control the plate crown by shifting the sine-shaped work rolls in the axial direction. The control range of the plate crown depends on a depth of sine-shaped roll profile because the roll radius varies continuously along the axial direction. When the roll profile is changed to improve the control range, the contact stress between the work roll and the back-up roll also changes. In the current study, the contact stress for various profiles and rolling conditions were analyzed using the finite element method and compared with results from Hertzian contact theory. A submodel method is used to increase the accuracy of the finite element analysis. The analysis results showed that the maximum increase in the contact stress was only 53MPa, so it is anticipated that no back-up roll spalling will occur.