• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.11
• /
• pp.1275-1284
• /
• 2010

100 MHz bandwidth and 1 Gbit/s data speed are needed in LTE-advanced for the next generation mobile communication system. Therefore, spectrum aggregation method has been studied recently to extend usable frequency bands. Also bandwidth utilization is increased since vacant frequencies are used to communicate. However, transceiver structure requires the digital RF and SDR. Therefore, frequency synthesizer and PA must operate over wide-bandwidth and RF impairments also increases in transceiver. Uplink of LTE advanced uses DFT-S OFDM using plural power amplifier. The effect of ICI increases in frequency domain of receiver due to phase noise and IQ imbalance. In this paper, we analyze influences of ICI in frequency domain of receiver considering phase noise and IQ imbalance in multiband system. Also, we separate phase noise and IQ imbalance effect from channel response in frequency domain of uplink system. And we propose a method to estimate the channel exactly and to compensate IQ imbalance and phase noise. Simulation result shows that the proposed method achieves the 2 dB performance gain of BER=$10^{-4}$.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.22 no.4
• /
• pp.383-399
• /
• 2020

Optimizing the spacing of the disc cutter is a key element in the design of the TBM cutter head, which determines the drilling performance of the TBM. The full-scale linear cutting test is known as the most reliable and accurate test for calculating the spacing of the disc cutter, but it has the disadvantage of costly and time-consuming for the full-scale experiment. In this study, through the numerical analysis study based on the discrete element method, the tendency between Specific Energy-S/P ratio according to uniaxial compression strength and penetration depth of rock was analyzed, and the optimum spacing of 17-inch disc cutter was derived. To examine the appropriateness of the numerical analysis model, the rolling force acting on the disc cutter was compared and reviewed with the CSM model. As a result of numerical analysis for the linear cutting test, the rolling force acting on the disc cutter was analyzed to be similar to the rolling force derived from the theoretical formula of the CSM model. From the numerical analysis on 5 UCS cases (50 MPa, 70 MPa, 100 MPa, 150 MPa, 200 MPa), it is found that the range of the optimum spacing of the disc cutter decreases as the rock strength increases. And it can be concluded that 80~100 mm of disc cutter spacing is the optimum range having minimum specific energy regardless of rock strength. This tends to coincide with the optimal spacing of previously reported disk cutters, which underpins the disk cutter spacing calculated through this study.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.5 no.3
• /
• pp.27-45
• /
• 2010

It is strongly believed that multicast will become one of the most promising services on internet for the next generation. Multicast service can be deployed either on network-layer or application-layer. IP multicast (network-layer multicast) is implemented by network nodes (i.e., routers) and avoids multiple copies of the same datagram on the same link. Despite the conceptual simplicity of IP multicast and its obvious benefits, it has not been widely deployed since there remain many unresolved issues. As an alternative to IP multicast, overlay multicast (application-layer multicast) implements the multicast functionality at end hosts rather than routers. This may require more overall bandwidth than IP multicast because duplicate packets travel the same physical links multiple times, but it provides an inexpensive, deployable method of providing point-to-multipoint group communication. In this paper we develop an efficient method applied greedy algorithm for solving two models of overlay multicast routing protocol that is aimed to construct MDST (Minimum Diameter Spanning Tree : minimum cost path from a source node to all its receivers) and MST (Minimum Spanning Tree : minimum total cost spanning all the members). We also simulate and analyze MDST and MST.

• Journal of KIISE:Computer Systems and Theory
• /
• v.33 no.12
• /
• pp.894-906
• /
• 2006

There are many difficulties to develop a mobile contents due to many constraints on mobile environments. It is difficult to make a good mobile contents with only visual reduction of existing contents on wire Internet. Therefore, it is essential to devise the data representation and to develop the authoring tool to meet the needs of the mobile contents market. We suggest the compact mobile contents to learn Chinese characters and developed its authoring tool. The animation which our system produces is realistic as if someone writes letters with pen or brush. Moreover, our authoring tool makes a user generate a Chinese character animation easily and rapidly although she or he has not many knowledge in computer graphics, mobile programming or Chinese characters. The method to generate the stroke animation is following: We take basic character shape information represented with several contours from TTF(TrueType Font) and get the information for the stroke segmentation and stroke ordering from simple user input. And then, we decompose whole character shape into some strokes by using polygonal approximation technique. Next, the stroke animation for each stroke is automatically generated by the scan line algorithm ordered by the stroke direction. Finally, the ordered scan lines are compressed into some integers by reducing coordinate redundancy As a result, the stroke animation of our system is even smaller than GIF animation. Our method can be extended to rendering and animation of Hangul or general 2D shape based on vector graphics. We have the plan to find the method to automate the stroke segmentation and ordering without user input.

• Korean Journal of Ecology and Environment
• /
• v.53 no.1
• /
• pp.63-72
• /
• 2020

In this study, to discuss on the applicability of eDNA as a new method to investigate fish diversity at streams, we applied eDNA at 4 streams (Geum River, Ji Stream, Hwangji Stream, Seomjin River), where endangered species are inhabits, with conventional survey (cast net and kick net). The average (±standard deviation) number of species investigated by eDNA were 19 species (±4.4), and it was relatively higher than average of conventional survey, 10 species (±4.8). Most of case, in this study, eDNA was more efficient than conventional survey. However, there were errors on species identification of Korean endemic species and aliied species from eDNA, and it seems the universal primer (MiFish primer set) is not suitable for them. Furthermore, some of endangered species, caught by conventional method, was not detected by eDNA. As the present universal primer is not suitable for identify the every freshwater fish species in Korea, the complementing or development of universal primer is needed, and the eDNA application after species specific marker development for detecting specific species like endangered species should be considered. In conclusion, if the manual for field survey method by eDNA is developed, we expect applicability enlargement for water ecosystem survey.

• Journal of the Korean Vacuum Society
• /
• v.12 no.4
• /
• pp.263-268
• /
• 2003

Precise thickness control and excellent properties of silicon nitride thin films are essential for the next-generation semiconductor and display devices. In this study, silicon nitride thin films were deposited by batch-type atomic layer deposition (ALD) method using $SiC1_4$ and $NH_3$ as the precursors at temperatures ranging from 500 to $600^{\circ}C$. Thin film deposition using a batch-type ALD reactor was a layer-by-layer atomic growth by self-limiting surface reactions, and the thickness of the deposited film can be controlled by the number of deposition cycles. The silicon nitride thin films deposited by ALD method exhibited composition, refractive index and wet etch rate similar with those of the thin films deposited by low-pressure chemical vapor deposition method at $760^{\circ}C$. The addition of pyridine mixed with precursors increased deposition rate by 50%, however, the films deposited with pyridine was readily oxidized owing to its unstable structure, which is unsuitable for the application to semiconductor or display devices.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.40 no.5
• /
• pp.403-412
• /
• 2022

As the 4th industrial revolution is in full swing and next-generation ICT(Information & Communications Technology) convergence technology is being developed, various smart construction technologies are being rapidly introduced in the construction field to respond to technological changes. In particular, since the earth-volume calculation process for site design accounts for a large part of the design cost at the construction site, related researches are being actively conducted to improve the efficiency of the process and accurately calculate the earth-volume. The purpose of this study is to present a method for quickly constructing the topography of a construction site in 3D and efficiently calculating earth-volume using the results. For this purpose, the construction site was constructed as a 3D realistic model using large-scale aerial photos obtained from UAV(Unmanned Aerial Vehicle). At this time, since the constructed 3D realistic model has a surface model structure in which volume calculation is impossible, the structure was converted into a 3D solid model to enable volume calculation. And we devised a methodology to calculate earth-volume based on CAD(Computer-Aided Design and Drafting) using the converted solid model. Automatically calculating earth-volume from the solid model by applying the method. As a result, It was possible to confirm a relative deviation of 1.52% from the calculated earth-volume from the existing survey results. In addition, as a result of comparative analysis of the process time required for each method, it was confirmed that the time required is reduced of 60%. The technique presented in this study is expected to be utilized as a technology for smart construction management, such as periodic site monitoring throughout the entire construction process, as well as cost reduction for earth-volume calculation.

• Journal of Korea Port Economic Association
• /
• v.39 no.2
• /
• pp.179-194
• /
• 2023

ASEAN is emerging as the next-generation market following BRICs. Korea is also an important economic cooperation partner as a second trading partner and third target for overseas investment. ASEAN is attracting attention as an attractive business place for many companies as a future investment area in the future. Therefore, the Korean government is strongly promoting a "New Southern Policy(NSP)" to develop cooperative relations with ASEAN. As ASEAN has recently emerged as a central area for shipping and logistics development, development cooperation and support for the shipping and logistics sector in the ASEAN region of neighboring countries are also active in entering the new southern region and the government is supporting it. In order to enter these countries, it is necessary to accurately understand the investment attraction system, strategy, and market for entering the business in other countries. Among the various methods of entering the overseas market, it is essential to understand the business selection and establishment method suitable for localization strategies such as foreign direct investment and establishment of foreign corporations. In order to understand the Overseas Investment Act and the Corporate Establishment Act of shipping and logistics-related companies who want to enter marine ASEAN countries, we will study the overseas investment method and the establishment method according to the type of company.

• Journal of the Korean Society of Tobacco Science
• /
• v.24 no.1
• /
• pp.67-73
• /
• 2002

In light of addressing consumer health concern, coping with anti-tobacco movement, and promoting new product, tobacco industry is actively pursuing to make a new generation of cigarettes with low tar and nicotine deliveries, and less harmful substances. Low tar and low nicotine cigarettes increases their market shares dramatically world wide, especially in KT&G, multinational tobacco companies, EU countries, even in China regulated by CNTC to set up yearly target to lower tar and nicotine deliveries. On the other hand, to design a new cigarette with reduced harmful substances begins to gain speed. The "modified Hoffmann list" publishes thirty plus substances in tobacco leaf and main smoke stream, which is the prime suspect causing health problems. Various ways and means are developed to reduce such components including new tobacco breeds, new curing method, tobacco leaf treatment before processing, selected filtration system, innovated casing system to reduce free radicals, as well as some non conventional cigarette products. In TSRC held this year, the main topic is related to reduce tobacco specific nitrosamines in tobacco leaf. The new generation of cigarette is in the horizon. It still needs a lot help to produce commercial products with satisfied taste and aroma characters. The flavor industry is not regulated by many governments demanding which ingredients might or might not be for tobacco use. However, most of the cigarette companies self impose a list of ingredients to guide flavor suppliers to design flavors. Unfortunately, the number of ingredients in those lists is getting shorter every year. It is understandable that the health is not the only reason. Some cigarette companies are playing safe to protect the company from potential lawsuit, while others are just copying from their competitors. Moreover, it is obvious that it needs more assistance from casings and flavors to design new generation of cigarettes with missing certain flavor components in tobacco leaf and main smoke stream. These flavor components are either non-existed or at lower level at new form of cured tobacco leaf or filtered in the main smoke stream along with reduced harmful substances. The use of carbon filters and other selected filtration system poses another tough task for flavor system design. Specific flavor components are missing from the smoke analysis data, which brings a notion of "carbon taste" and "dryness" of mouth feel. It is ever more demanded by cigarette industry to flavor suppliers to produce flavors as body enhancer, tobacco notes, salivating agents, harshness reducer, and various of aromatic notes provided they are safe to use. Another trend is that water based flavor or flavor with reduced ethanol as solvent is gaining popularity. It is preferred by some cigarette companies that the flavor is compounded with all natural ingredients or all ingredients should he GMO free. The new generation of cigarettes demands many ways of new thinking process. It is also vital for tobacco industry. It reflects the real needs for the consumers that the cigarette product should be safe to use as well as bearing the taste and aroma characters smokers always enjoyed. An effective tobacco flavor system is definitely a part of the equation. The global trend of tobacco industry is like trends of any other industries lead by consumer needs, benefited with new technology availability, affected by the global economy, and subjected for various rules and regulations. Anti-tobacco organizations and media exceptionally scrutinize cigarette, as a legal commercial product. Cigarette is probably the most studied commercial product for its composition, structure, deliveries, effects, as well as its new developmental trend. Therefore, any new trend of cigarette development would be within these boundaries. This paper is trying to point out what it would be like for tobacco industry in the next few yews and what concerns the tobacco industry. It focuses mostly on the efforts to produce safer cigarettes. It is such a vital task for the tobacco industry and its affiliate industries such as cigarette papers, filters, flavors, and other materials. The facts and knowledge presented in this paper might be well known for the public. Some of the comments and predictions are very much personal opinion for a further discussion.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.34 no.1
• /
• pp.118-128
• /
• 2016

The purpose of this study is to present efficient methods of preserving and managing the fish shelter forest in Mulgun-ri on the southern coast of Korea on the basis of its humanistic, sociological and ecological characteristics. The study object is Korean natural monument No. 150, which is presumed to have been forested by descendants of Jeonju Lee Family who settled there, and village rituals are held every October to pray for the peace of the village. The forest is managed by Namhae-gun as a historical and cultural resource as well as its disaster-preventing, economic, and environmental and ecological functions. The linear form of the area is $23,962.6m^2$ and farmland(48.5%) and urbanization area(38.2%) are extensively located in its periphery area. Actual vegetation was sub-classified into three types of land according to use pressure and whether or not damage was done: land where its stratification was formed; land where it was restored, and the land where it was damaged. Plant communities were sub-classified into Aphananthe aspera community(I) and Zelkova serrata community(II) which had a low use pressure; Z. serrata-Chionanthus retusa-A. aspera community(III) and A. aspera-Z. serrata community(IV) which had a high use pressure; and Celtis sinensis-A. aspera community(V) whose underlayer was damaged by use. Fragmentation of the forest is under way and its inside vegetation growth is hampered due to the installation of traffic and resting facilities such as the through roads costal roads, wooden-deck walkways, parking lots, washstands, etc. As a restoration management plan for this, the following were required: an establishment of preferred restoration area; a selection of restoration vegetation species; and an appropriate restoration method. The damaged area($7,868.2m^2$) will have to be set up as the preferred restoration area; seedlings of restored vegetation species should be raised with dominant species within the forest(i.e., Z. serrata, A. aspera, C. sinensis, and C. retusa) as their 'mother trees' for the benefit of for the next-generation forest; and sub-tree and shrub layer should be complementarily planted with 5 and 115 trees(unit $100m^2$) respectively to facilitate the formation of a multi-layered vegetation structure. In addition, resting facilities scattered inside the forest should be demolished; and indiscriminate use of them should be controlled; management and monitoring should be carried out so that the area can be preserved and restored as a deciduous broad-leaved forest.