• Steel and Composite Structures
• /
• 제5권1호
• /
• pp.49-70
• /
• 2005

This paper reports on finite element analysis techniques that may be applied to the study of circular hollow structural sections and related bearing connection geometries. Specifically, a connection detail involving curved steel saddle bearings and a Structural Tee (ST) connected directly to a large-diameter Hollow Structural Section (HSS) truss chord, near its open end, is considered. The modeling is carried out using experimentally verified techniques. It is determined that the primary mechanism of failure involves a flexural collapse of the HSS chord through plastification of the chord wall into a well-defined yield line mechanism; a limit state for which a shell-based finite element model is well-suited to capture. It is also found that classical metal plasticity material models may be somewhat limited in their applicability to steels in fabricated tubular members.

• 대한기계학회논문집A
• /
• 제22권2호
• /
• pp.289-301
• /
• 1998

The present study attempted to numerically simulate the process in detail by developing an appropriate physical modeling and the corresponding numerical analysis for precision injection and injection/compression molding process of center-gated disk. In part I, a physical modeling and associated numerical analysis of injection molding with a compressible viscoelastic fluid model are presented. In the distribution of birefringence, the packing procedure results in the inner peaks in addition to the outer peaks near the mold surface, and values of the inner peaks increase with the packing time. Also, values of the density in the core region increase with the packing time. From the numerical results, we also found that birefringence becomes smaller as the melt temperature gets higher and that it is insignificantly affected by the flow rate and the mold temperature. As far as the density distribution is concerned, mold temperature affected the distribution of density especially near the wall. But it was not significantly affected by flow rate and melt temperature. Numerical results of birefringence coincided with experimental data qualitatively but didn't quantitatively.

• 한국수자원학회논문집
• /
• 제52권10호
• /
• pp.697-706
• /
• 2019

다상흐름 모델링 기법과 하이브리드 난류 모델링 기법을 결합한 수치모형을 이용하여 사각형 수로에서의 중력류를 수치모의 하였다. 이 연구에서 적용한 다상흐름 해석기법은 밀도가 큰 중력류 유체, 상대적으로 밀도가 작은 주변류 유체 그리고 자유수면 위에서 흐르는 공기를 3개의 상으로 처리하며, 각 상에 대해서 분리된 흐름 지배방정식을 적용한다. 난류흐름은 벽경계 근처에서는 RANS 모드로 모의하고 벽에서 떨어진 영역에서는 LES 모드로 해석하는 하이브리드 RANS/LES 방법의 일종인 IDDES 기법을 이용하여 해석한다. 이 연구에서 적용한 모델링 기법은 중력류의 머리의 전파속도를 실험값과 일치하게 잘 예측하는 것으로 나타났다. 수치해석 결과는 아울러 낮은 레이놀즈수 난류모형을 이용한 RANS 수치모의에서 이용되는 정도의 격자해상도에서도 큰 규모의 Kelvin-Helmholtz 형식의 경계면 와의 발달과 이들 와가 지속적으로 3차원 형식의 붕괴를 거쳐 작은 난류구조로 분해되면서 난류에너지가 소산되는 현상을 성공적으로 예측함을 보여준다. 적용한 수치모의 기법은 공학적으로 접근 가능한 격자해상도에서 돌출-쪼개짐 흐름 불안정을 동반한 중력류 머리부분의 3차원 거동 특성을 잘 재현하며, 이 결과는 보다 높은 격자해상도에서 구해진 LES 결과에 상응하는 것으로 나타났다. 이 연구결과는 하이브리드 난류모델링 기법과 다상흐름 해석기법을 병합한 수치모형이 자연상태에서 복잡한 중력류의 물리적 거동을 예측하는데 공학적으로 유망한 방법임을 보여준다.

• 대한기계학회논문집
• /
• 제11권3호
• /
• pp.395-408
• /
• 1987

본 연구에서는 이러한 예측능력 향상에 중점을 두어 2차원 축대칭 모델엔진 실린더내의 유동장 및 열전달특성을 예측할 수 있는 새로운 코오드를 개발하여 실험자 료와의 비교를 통해 프로그램을 검증하고 흡입 및 압축과정을 수치시뮬레이션한 결과 를 보고하고자 한다. 아울러 선회속도의 영향도 고찰하였다. 난류모델은 K-.epsilon.난류 모델을 압축성 효과가 고려되도록 수정된 모델을 사용하였으며 TEACH코오드를 기본으 로 하여 비정상 압축성 유동을 풀 수 있는 새로운 알고리즘을 개발하여 수정하였다.

• 대한기계학회논문집B
• /
• 제23권8호
• /
• pp.1063-1071
• /
• 1999

Fine grid calculations are reported for the developing turbulent flow in a curved duct of square cross-section with a radius of curvature to hydraulic diameter ratio ${\delta}=Rc/D_H=3.357 $ and a bend angle of 720 deg. A sequence of modeling refinements is introduced; the replacement of wall function by a fine mesh across the sublayer and a low Reynolds number algebraic second moment closure up to the near wall sublayer in which the non-linear return to isotropy model and the cubic-quasi-isotropy model for the pressure strain are adopted; and the introduction of a multiple source model for the exact dissipation rate equation. Each refinement is shown to lead to an appreciable improvement in the agreement between measurement and computation.

• Journal of Advanced Marine Engineering and Technology
• /
• 제39권2호
• /
• pp.136-142
• /
• 2015

The shell and tube heat exchanger is an essential part of a power plant for recovering transfer heat between the feed water of a boiler and the wasted heat. The baffles are also an important element inside the heat exchanger. Internal materials influence the flow pattern in the bed. The influence of baffles in the velocity profiles was observed using a three-dimensional PIV (Particle Image Velocimetry) around baffles in a horizontal circular tube. The velocity of the particles was measured before the baffle and between them in the test tube. Results show that the velocity vectors near the front baffle flow along the vertical wall, and then concentrate on the upper opening of the front baffle. The velocity profiles circulate in the front and rear baffle. These profiles are related to the Reynolds number (Re) or the flow intensity. Velocity profiles at lower Re number showed complicated mixing to obtain the velocities and concentrate on the lower opening of the rear baffle as front wall. Numerical simulations were performed to investigate the effects of the baffle and obtain the velocity profiles between the two baffles. In this study, a commercial CFD package, Fluent 6.3.21 with the turbulent flow modeling, k-${\epsilon}$ are adopted. The path line and local axial velocities are calculated between two baffles using this program.

• 대한기계학회논문집A
• /
• 제24권5호
• /
• pp.1323-1330
• /
• 2000

Recently, injection molding process became more popular than ever to produce large quantities of high precision products or optical products. Especially, optical disk that was made by injection mol ding process has been used for many years as a music play media or computer sub-device. The density of data in disk media has been increased continuously. But those optical disks can cause sensorial problems because of high birefringence or deformation from the residual stresses in the media. Therefore, it is necessary to study the effects of various process conditions on the final bireffingence structure in injection-molded disks for producing precision injection-molded products. In the present paper we have focussed on the effect of holding and compression pressures on the optical anisotropy remaining in the MOD by examining the gapwise distribution of birefringence and extinction angle. The effect of holding pressure was found to form the inner two bireffingence peaks. But the effect of compression pressure on the bireffingence distribution was found to make the uniform distribution near the center in the gapwise direction. Finally, the value of the birefringence near the wall decreased as the mold temperature increased.

• 한국정밀공학회지
• /
• 제12권12호
• /
• pp.109-119
• /
• 1995

A driveline incorporating universal joints when driving through an angle can excite various components in a vehicle with second order excitation of torsional and bending vibrations, being transmitted either audibly(noise), or physically(vibration). For a certain range of vehicle dpeed noises can be radiated from the cab wall, in which resonances occur by the excitations transmitted from the driveline as a vibration source. In this paper, the excitation mechanism of cab noises is studied especially for the vehicle speed range of 65 .approx. 75 km/h through the simulation for torsional vibrations of the driveline and for bending vibrations of the cab of an 11 Ton grade Cargo Truck, and verified additionally by vibration and noise measurements. As a result, it is found that the uncomfortable noises in the cab are caused mainly by the abrupt increase of the joint angle of driveline near the axle differential resulted from the excessive clearance alignment of the leaf spring gate.

• 대한조선학회논문집
• /
• 제41권2호
• /
• pp.61-69
• /
• 2004

In this study, flow around rudder is analyzed by utilizing the numerical calculation, and the rudder open water test is performed to validate the calculation. The aim of this study is to design the new rudder shape to improve manoeuvring performance. In first, flow around two-dimensional rudder section is analyzed to understand the characteristics of section profile. And the calculation for all-movable rudders is performed and compared with results of rudder open water test. It is hard to numerically predict the drag force because the value is sensitive to the turbulence modeling and grid spacing near the wall. However, the lift force is predicted well. And we can prove that concave profile of the rudder section produce more lift and torque than convex one as a experiment. However PANEL method that ignore viscous effect cannot distinguish the difference of them. So, we can look for the numerical tool to be developed the new rudder shape.

• 한국입자에어로졸학회지
• /
• 제9권3호
• /
• pp.163-171
• /
• 2013

Soot particles emitted from combustion processes are often coated by non-absorbing organic materials, which enhance the global warming effect of soot particles. It is of importance to study the condensation characteristics of soot particles experimentally and theoretically to reduce the uncertainty of the climate impact of soot particles. In this study, the condensational growth of soot particles in a tubular coater was modeled by a one-dimensional (1D) plug flow model and a two-dimensional (2D) laminar flow model. The effects of 2D heat and mass transports on the predicted particle growth were investigated. The temperature and coating material vapor concentration distributions in radial direction, which the 1D model could not accounted for, affected substantially the particle growth in the coater. Under the simulated conditions, the differences between the temperatures and vapor concentrations near the wall and at the tube center were large. The neglect of these variations by the 1D model resulted in a large error in modeling the mass transfer and aerosol dynamics occurring in the coater. The 1D model predicted the average temperature and vapor concentration quite accurately but overestimated the average diameter of the growing particles considerably. At the outermost grid, at which condensation begins earliest due to the lowest temperature and saturation vapor concentration, condensing vapor was exhausted rapidly because of the competition between condensations on the wall and on the particle surface, decreasing the growth rate. At the center of the tube, on the other hand, the growth rate was low due to high temperature and saturation vapor concentration. The effects of Brownian diffusion and thermophoresis were not high enough to transport the coating material vapor quickly from the tube center to the wall. The 1D model based on perfect radial mixing could not take into account this phenomenon, resulting in a much higher growth rate than what the 2D model predicted. The result of this study indicates that contrary to a previous report for a thermodenuder, 2D heat and mass transports must be taken into account to model accurately the condensational particle growth in a coater.