• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.05a
• /
• pp.47-52
• /
• 2004

Springback comes from the release of residual stress after forming. The control of phenomenon is especially important in the sheet metal forming since there are no other practical methods available to correct the dimensional inaccuracy from springback. Therefore the accurate predication before the die machining has been a long goal in the Held of sheet metal forming. The aim of the present study is to enhance the prediction capability of finite element(FE) analysis for the springback phenomenon. For this purpose FE analysis for V-bending has been carried out with the commercial programs, LS-DYNA. The FE analysis results have been validated through the comparison of experimental. The experimental results measured directly by the strain gauge have given the confidence to FEA.

• Progress in Superconductivity
• /
• v.8 no.1
• /
• pp.104-107
• /
• 2006

For the practical application on SCFCL(Superconducting fault current limiters), Bi-2212 tubes were fabricated by Centrifugal Forming Process(CFP). The tubes were annealed at 830, 840, $850^{\circ}C$, respectively for 80 hours in oxygen atmosphere. The tubes heat treated at $840^{\circ}C$ demonstrated better electric characteristics than the tubes heat treated at 830 and $850^{\circ}C$. The typical value measured at 77 K in the self field was around 556 A. In terms of cooling effect on superconducting properties, it was found the electrical properties were quite dependent on the mold design and shapes. In order to check uniformity along the tube, EFDLab fur heat and fluid analysis of NIKA was adopted. It was found out that the simulation data was quite well matched with experimental results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.229-231
• /
• 2005

HVDC(High Voltage Direct Current) is an underwater cable between Jeju Island and Haenam in main land and supplies approximately 50% of electrical usage in Jeju Island. If there is any power failure due to HVDC, it will cost approximately 50,000 US dollars per day including Thermal Electrical Generation. Therefore it is absolutely necessary to recover the problem in rapid timely basis. In conclusion, evaluation methode of HVDC cable is needed urgently to upgrade current HVDC underwater cable repair technique in Korea to minimize the cost and time factors.

• Asian-Australasian Journal of Animal Sciences
• /
• v.18 no.4
• /
• pp.475-478
• /
• 2005

This study was conducted to evaluate feeding value of berseem and lucerne silage as a replacement for conventional fodder (berseem fodder) in lactating Nili buffaloes. Fifteen early lactating multi-parous Nili buffaloes, five buffaloes in each group were allotted three experimental diets. Berseem and lucerne fodders were ensiled at 30% DM (wheat straw was used to adjust the DM of fodders) with molasses (at the rate of 2% of fodder DM) in two bunker silos for 30 days. The diets contained 75% DM from berseem fodder (BF), 75% DM from berseem silage (BS) and 75% DM from lucerne silage (LS). Each diet contained 25% concentrate DM. Diets were mixed daily and fed twice a day at ad libitum intakes. Dry matter intake (DMI) was significantly higher (13.8 kg/d) in buffaloes fed BF diet than those fed LS (12.5 kg/d) and BS (11.9 kg/day) diets. The differences in digestible DMI and DMI as percent body weight were significant between fodder and silage based diets but non-significant when BS and LS were compared. Lower DMI with silage-based diets was probably because of low silage pH. Intake of NDF (NDFI) was higher (5.68 kg/d) in buffaloes fed BF diet followed by those fed LS (5.50 kg/d) and BS (5.00 kg/d) diets. The difference was significant (p<0.05) across fodder and silage based diets but NDFI was non-significant across both silage-based diets. The apparent DM digestibility was significantly different (p<0.05) between fodder and silage-based diets but was non-significant between LS and BS diets. Four percent fat corrected milk yield was significantly different (p<0.05) between fodder and silage-based diets but was non-significant between LS and BS diets. Higher milk yield with fodder based diet was because of more digestible nutrient intake (Table 3) compared with silage based diets. Milk CP, TP and NPN and SNF did not show any treatment effects. The present results indicated that the berseem and lucerne fodder ensiled at 30% DM level with 2% molasses could safely replace (75% DM) the conventional leguminous fodder in the diets of lactating Nili buffaloes.

• The Journal of Advanced Prosthodontics
• /
• v.12 no.4
• /
• pp.181-188
• /
• 2020

PURPOSE. The effect of core design on the fracture resistance of zirconia-lithium disilicate (LS2) bilayered crowns for anterior teeth is evaluated by comparing with that of metal-ceramic crowns. MATERIALS AND METHODS. Forty customized titanium abutments for maxillary central incisor were prepared. Each group of 10 units was constructed using the same veneer form of designs A and B, which covered labial surface to approximately one third of the incisal and cervical palatal surface, respectively. LS2 pressed-on-zirconia (POZ) and porcelain-fused-to-metal (PFM) crowns were divided into "POZ_A," "POZ_B," "PFM_A," and "PFM_B" groups, and 6000 thermal cycles (5/55 ℃) were performed after 24 h storage in distilled water at 37 ℃. All specimens were prepared using a single type of self-adhesive resin cement. The fracture resistance was measured using a universal testing machine. Failure mode and elemental analyses of the bonding interface were performed. The data were analyzed using Welch's t-test and the Games-Howell exact test. RESULTS. The PFM_B (1376. 8 ± 93.3 N) group demonstrated significantly higher fracture strength than the PFM_A (915.8 ± 206.3 N) and POZ_B (963.8 ± 316.2 N) groups (P<.05). There was no statistically significant difference in fracture resistance between the POZ_A (1184.4 ± 319.6 N) and POZ_B groups (P>.05). Regardless of the design differences of the zirconia cores, fractures involving cores occurred in all specimens of the POZ groups. CONCLUSION. The bilayered anterior POZ crowns showed different fracture resistance and fracture pattern according to the core design compared to PFM.

• The Korean Journal of Ecology
• /
• v.28 no.5
• /
• pp.295-303
• /
• 2005

The sexual dimorphism and intra sexual dimorphism in males of Rhinogobius brunneus were investigated at Jiam stream, a tributary of the Bukhan river from May, 2005. The frequency distributions in standard length were similar for the females and maleLs, but maleSs were smaller than the females and maleLs. The ratio of MaleL (N=79) to males (N=79) was 1 : 0.46. The comparison between female (N=79) and maleL (N=79) gave significant differences (P<0.05) in 18 morphometric characteristics (SNL, AHD, PHD, ML, DL, MW, AHW, IFW, PHW, ED, HL, FDFL, SDFB, CFL, AFB, VFL, PFL, PFB) and 12 characteristics (SNL, AHD, ML, DL, MW, AHW, IFW, PHW, HL, FDFI, CFL, PFB) (P<0.001). Eight morphometric characteristics (SNL, ML, DL, MW, HL, CFL, VFL, PFL) in female (N=36) and males (N=36) had significant differences (P<0.05) and three characteristics (ML, DL, HL) had very significant differences (P<0.001). Eleven characteristics (SNL, AHD, PHD, ML, DL, MW, AHW, IFW, PHW, HL, FDFL) were significantly different in maleL (N=36) and males (N=36) (P<0.05) and six (ML, DL, MW, AHW, HL, FDFL) were very significantly different (P<0.001).

• Journal of Environmental Science International
• /
• v.17 no.8
• /
• pp.933-941
• /
• 2008

The formation of $Co_nTiO_{n+2}$ compounds, i.e., $CoTiO_3$ and $CO_2TiO_4$, in a 5wt% $CoO_x/TiO_2$ catalyst after calcination at different temperatures has been characterized via scanning electron microscopy (SEM), Raman and X-ray photoelectron spectroscopy (XPS) measurements to verify our earlier model associated with $CO_3O_4$ nanoparticles present in the catalyst, and laboratory-synthesized $Co_nTiO_{n+2}$ chemicals have been employed to directly measure their activity profiles for CO oxidation at $100^{\circ}C$. SEM measurements with the synthetic $CoTiO_3$ and $CO_2TiO_4$ gave the respective tetragonal and rhombohedral morphology structures, in good agreement with the earlier XRD results. Weak Raman peaks at 239, 267 and 336 $cm^{-1}$ appeared on 5wt% $CoO_x/TiO_2$ after calcination at $570^{\circ}C$ but not on the catalyst calcined at $450^{\circ}C$, and these peaks were observed for the $Co_nTiO_{n+2}$ compounds, particularly $CoTiO_3$. All samples of the two cobalt titanate possessed O ls XPS spectra comprised of strong peaks at $530.0{\pm}0.1$ eV with a shoulder at a 532.2-eV binding energy. The O ls structure at binding energies near 530.0 eV was shown for a sample of 5 wt% $CoO_x/TiO_2$, irrespective to calcination temperature. The noticeable difference between the catalyst calcined at 450 and $570^{\circ}C$ is the 532.2 eV shoulder which was indicative of the formation of the $Co_nTiO_{n+2}$ compounds in the catalyst. No long-life activity maintenance of the synthetic $Co_nTiO_{n+2}$ compounds for CO oxidation at $100^{\circ}C$ was a good vehicle to strongly sup port the reason why the supported $CoO_x$ catalyst after calcination at $570^{\circ}C$ had been practically inactive for the oxidation reaction in our previous study; consequently, the earlier proposed model for the $CO_3O_4$ nanoparticles existing with the catalyst following calcination at different temperatures is very consistent with the characterization results and activity measurements with the cobalt titanates.

• Honam Mathematical Journal
• /
• v.35 no.4
• /
• pp.707-716
• /
• 2013

The present paper consists of two parts. Since the recent paper [4] proved that an Alexandroff $T_0$-space is a semi-$T_{\frac{1}{2}}$-space, the first part studies semi-open and semi-closed structures of the Khalimsky nD space. The second one focuses on the study of a relation between the LS-property of ($SC^{n_1,l_1}_{k_1}{\times}SC^{n_2,l_2}_{k_2}$, k) relative to the simple closed $k_i$-curves $SC^{n_i,l_i}_{k_i}$, $i{\in}\{1,2\}$ and its normal k-adjacency. In addition, the present paper points out that the main theorems of Boxer and Karaca's paper [3] such as Theorems 4.4 and 4.7 of [3] cannot be new assertions. Indeed, instead they should be attributed to Theorems 4.3 and 4.5, and Example 4.6 of [10].

• Proceedings of the Korean Information Science Society Conference
• /
• 2003.10a
• /
• pp.301-303
• /
• 2003

사용자 쓰레드와 시스템 쓰레드간의 1:1 맵핑 모델은 병렬성을 지원하는 장점이 있고, M: N 맵핑은 병렬성 지원과 빠른 문맥교환의 장점이 있다. 리눅스 자바 가상 머신에서는 1:1 맵핑 모델만을 지원한다. 연성 실시간을 보장하기 위해서는 쓰레드간의 문맥교환을 최소화하여 성능 향상시킬 필요가 있다. 이 논문에서는 자바 어플리케이션 레벨에서 경량 프로세스(Light Weight Process, LWP) 개념을 도입하여 리눅스 자바 가상 머신에서 M: N 맵핑을 지원하는 자바 쓰레드 모델을 제안한다. 제안한 모델은 그린 쓰레드 (Green Thread)의 빠른 문맥교환과 네이티브 쓰레드(Native Thread)의 병렬성 지원 장점을 혼합한 것으로 빠른 처리속도와 자바 플랫폼의 독립성을 그대로 유지할 수 있다. 또한, MTR-LS 알고리즘을 경량 프로세스 스케줄링에 채택함으로서, 자바 응용프로그램의 연성 실시간을 보장한다. 1:l 및 M:1 맵핑 모델과의 성능 비교를 통해 제안한 모델이 좋은 성능과 연성 실시간을 보장한다는 것을 보인다.

• The korean journal of orthodontics
• /
• v.12 no.2
• /
• pp.79-93
• /
• 1982

The purpose of orthodontic treatment is to achieve normal occlusion and good facial esthetics for individual patients. To produce harmonized facial balance, treatment planning for patient who require orthodontic treatment should include both a hard tissue and soft tissue cephalometric analysis. Author studied to derive the normal standards of soft tissue profile in Koreans by roentgenocephalometric analysis. For this study 12 soft tissue profile landmarks were plotted and 23 linear length, 9 soft tissue thickness, 8 vertical height length, 12 angles of soft tissue profile, and 3 vertical proportion were measured. The subjects consisted of 166 males and 209 females from 7 to 19 years with normal occlusion and acceptable profiles, and were divided into five groups according to age. The obtained results were as follows; 1. From the basis of N-Pog (Nasion-Pogonion) plane, the growth of facial soft tissue in the middle region especially nose area was greater than others facial region. 2. From the basis of G-Pog' (Glabella-soft tissue Pogonion) plane, the values of linear measurement of soft tissue Nasion and Inferior labial sulcus decreased and nose tip grew forward as growing older. 3. The growth of the facial soft tissue thickness was greatest in superior labial sulcus and the thickness of soft tissue nasion gradually became thinner as growing old. 4. The thickness of upper and lower lip was 14.47mm, 14.57mm in adulr male, 12.76mm, 13.78mm in adult female. 5. The soft tissue thickness of the lower lip was thicker than that of upper lip in all age groups and both sexes, 6. The vertical length of the upper and lower lips were 25.04mm, 49.97mm in adult male and 23.50mm, 48.39mm in adult female. 7. By the significant test, there were significant difference between male and female in fifth adult group on all vertical length measurements of lower face. 8. In fifth adult group, the perpendicular distance from LS, LI to Steiner's line and Ricketts' esthetic line were as follow; Steiner line to LS, LI were 7.98mm, 5.84mm in male. Steiner line to LS, LI were 6.71mm, 5.08mm in female. Ricketts' esthetic line to LS, LI were -0.40mm, 1.72mm in male. Ricketts' esthetic line to Ls, LI were -1.38mm 0.65mm in female. 9. In fifth adult group, the facial convexity angle and lower facial component angle were $171.17^{\circ}142.94^{\circ}$ in male and $172.5^{\circ}$, $144.41^{\circ}$ in female.