• Journal of Power System Engineering
• /
• v.16 no.4
• /
• pp.30-36
• /
• 2012

A scroll expander has been designed to produce a shaft power from a R134a Rankine cycle for electricity generation. Heat was supplied to the Rankine cycle through a heat exchanger, which received heat from another cycle of water. In the water cycle, water was heated up in a boiler using biogenic solid fuel. The designed scroll expander was a horizontal type, and a trochoidal oil pump was employed for oil supply to bearings and Oldham-ring keys. For axial compliance, a back pressure chamber was created on the backside of the orbiting scroll base plate. Numerical study has been carried out to estimate the performance of the designed scroll expander. The expander was estimated to produce the shaft power of about 2.9 kW from a heat supply of 36 kW, when the temperature of R134a was $80^{\circ}C$ and $35^{\circ}C$ at the evaporator and condenser of the Rankine cycle, respectively. The expander efficiency was about 70.5%. When the amount of heat supply varied in the ranges of 7.5~55 kW, the expander efficiency changed in the range of 45.6~70.5%, showing a peak efficiency of 70.5% at the design shaft speed.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.12
• /
• pp.1195-1200
• /
• 2007

Torque of a rotating shaft has been mostly measured by strain gages combined with either a slip ring or telemetry. However, these methods have severe inherent problems like low S/N ratio, high cost, limited number of channels and difficult installation. In this paper, a new method using FBG(fiber bragg grating) sensors and a rotary optical coupler for online non-contact torque monitoring is suggested. FBG sensor can measure both strain and temperature, and has much batter characteristics than those of a strain gage. A rotary optical coupler is a optical connecting device between a rotating shaft and stationary side without any physical contact. It has been devised for transmitting light between a rotating optical fiber and a stationary optical fiber. The proposed method uses this rotary optical coupler to connect FBG sensors on the rotating shaft to instruments at stationary side. And a reference FBG sensor is also applied to compensate the insertion loss change of the rotary optical coupler due to rotation. Three FBG sensors have been fabricated in a single optical fiber. Two FBG sensors are attached on the shaft surface to measure torque and one sensor is installed at the shaft center to compensate the insertion loss change. The torque of a rotating shaft has been successfully measured by the suggested method proving its superior performance potential.

• Molecules and Cells
• /
• v.23 no.2
• /
• pp.175-181
• /
• 2007

The present study was undertaken to determine whether $SM22{\alpha}$ participates in the regulation of vascular smooth muscle contractility using $SM22{\alpha}$ knockout mice and, if so, to investigate the mechanisms involved. Aortic ring preparations were mounted and equilibrated in organ baths for 60 min before observing contractile responses to 50 mM KCl, and then exposed to contractile agents such as phenylephrine and phorbol ester. Measurement of isometric contractions using a computerized data acquisition system was combined with molecular or cellular experiments. Interestingly, the aortas from $SM22{\alpha}$-deficient mice ($SM22^{-/-LacZ}$) displayed an almost three-fold increase in the level of $SM22{\beta}$ protein compared to wild-type mice, but no change in the levels of caldesmon, actin, desmin or calponin. $Ca^{2+}$-independent contraction in response to phenylephrine or phorbol ester was significantly decreased in the $SM22{\alpha}$-deficient mice, whereas in the presence of $Ca^{2+}$ neither contraction nor subcellular translocation of myosin light chain kinase (MLCK) in response to phenylephrine or 50 mM KCl was significantly affected. A decrease in phosphorylation of extracellular signal regulated kinase (ERK) 1/2 was observed in the $SM22{\alpha}$-deficient mice and this may be related to the decreased vascular contractility. Taken together, this study provides evidence for a pivotal role of $SM22{\alpha}$ in the regulation of $Ca^{2+}$-independent vascular contractility.

• Korean Journal of Materials Research
• /
• v.7 no.1
• /
• pp.62-68
• /
• 1997

In the first part of the paper, the crack growth process in rolling contact fatigue has been investigated on ring type plate specimens, in which crack growth is two dimensional and cracks are observed on the side surface of the specimens. The results have shown that cracks are initated from the contact surface in tensile mode in the direction approximately normal to the contact surface and after some short length of growth, shear mode growth occurs from the tip of the crack and it grows until the separation of the surface layer, namely flakung type failure, occurs. In the second part, mode U fatigue crack growth tests have been made by using an apparatus designed based on the concept that the subsurface fatigue crack growth in rolling contact fatigue is the mode U fatigue crack growth under the stress state where the tensile mode growth is suppressed by compression stress. The rest results have shown that the mode U fatigue crack growth occurs if the superposed compression stress is enough to suppress the tensile mode growth.

• Korean Journal of Materials Research
• /
• v.27 no.7
• /
• pp.386-391
• /
• 2017

Using a customized diffusion bonder, we executed diffusion bonding for ring shaped white gold and red gold samples (inner, outer diameter, and thickness were 15.7, 18.7, and 3.0 mm, respectively) at a temperature of $780^{\circ}C$ and applied pressure of 2300 N in a vacuum of $5{\times}10^{-2}$ torr for 180 seconds. Optical microscopy, field emission scanning electron microscopy (FE-SEM), and energy-dispersive X-ray spectroscopy (EDS) were used to investigate the microstructure and compositional changes. The mechanical properties were confirmed by Vickers hardness and shear strength tests. Optical microscopy and FE-SEM confirmed the uniform bonding interface, which was without defects such as micro pores. EDS mapping analysis confirmed that each gold alloy was 14K with the intended composition; Ni and Cu was included as coloring metals in the white and red gold alloys, respectively. The effective diffusion coefficient was estimated based on EDS line scanning. Individual values of Ni and Cu were $5.0{\times}10^{-8}cm^2/s$ and $8.9{\times}10^{-8}cm^2/s$, respectively. These values were as large as those of the melting points due to the accelerated diffusion in this customized diffusion bonder. Vickers hardness results showed that the hardness values of white gold and red gold were 127.83 and 103.04, respectively, due to solid solution strengthening. In addition, the value at the interface indicated no formation of intermetallic compound around the bonding interface. From the shear strength test, the sample was found not to be destroyed at up to 100,000 gf due to the high bonding strength. Therefore, these results confirm the successful diffusion bonding of 14K white-red golds with a diffusion bonder at a low temperature of $780^{\circ}C$ and a short processing time of 180 seconds.

• Archives of Pharmacal Research
• /
• v.27 no.5
• /
• pp.512-517
• /
• 2004

The structural relationship of 16 asiatic acid (AA) derivatives, including AA and asiaticoside (AS) to cytotoxicity and anti-hepatofibrotic activity in HSC-T6 cells, were investigated. Cytotoxicities of AA derivatives varied from 5.5 $\mu$M to over 2000 $\mu$M of $IC_{50}$/ depending on AA functional group modifications. Substituting the hydroxyl group at the C(2) to N≡C and substituting bulky groups for dihydroxyl groups at (3), (23) of the A-ring increased the cytotoxicity, but keto group at C(11) and benzoyl ester at C(2) were greatly reduced it. Modification of the carboxylic acid group at C28 also reduced the cytotoxicity. The collagen synthesis determined by hydroxyproline content in the cells was inhibited from a maximum of 48% (Zlx-i-85 and 87) to 15% (AS) by AA derivatives. The anti-hepatofibrotic effect of these compounds might be due to the reduced expression of prolyl 4-hydroxylase $\alpha$ and $\beta$ subunits and TIMP2. However, the inhibition of collagen by asiaticoside derivatives did not show any structural-activity relationship.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.10
• /
• pp.3052-3058
• /
• 2014

In this article, we have designed and synthesized a novel donor-${\pi}$-acceptor (D-${\pi}$-A) type porphyrin-based sensitizer (denoted UI-5), in which a carboxyl anchoring group and a 9,9-dimethyl fluorene were introduced at the meso-positions of porphyrin ring via phenylethynyl and ethynyl bridging units, respectively. Long alkoxy chains in ortho-positions of the phenyls were supposed to reduce the degree of dye aggregation, which tends to affect electron injection yield in a photovoltaic cell. The cyclic voltammetry was employed to determine the band gap of UI-5 to be 1.41 eV based on the HOMO and LUMO energy levels, which were estimated by the onset oxidation and reduction potentials. The incident monochromatic photon-to-current conversion efficiency of the UI-5 DSSC assembled with double-layer (20 nm-sized $TiO_2$/400 nm-sized $TiO_2$) film electrodes appeared lower upon overall ranges of the excitation wavelengths, but exhibited a higher value over the NIR ranges (${\lambda}$ = 650-700 nm) compared to the common reference sensitizer N719. The UI-5-sensitized cell yielded a relatively poor device performance with an overall conversion efficiency of 0.74% with a short circuit photocurrent density of $3.05mA/cm^2$, an open circuit voltage of 0.54 mV and a fill factor of 0.44 under the standard global air mass (AM 1.5) solar conditions. However, our report about the synthesis and the photovoltaic characteristics of a porphyrin-based sensitizer in a D-${\pi}$-A structure demonstrated a significant complex relationship between the sensitizer structure and the cell performance.

• Journal of Veterinary Clinics
• /
• v.22 no.3
• /
• pp.220-227
• /
• 2005

Although ketamine has been used in the field of anesthetic medicine for its safety and favourable respiratory effects, the cardiovascular effects of ketamine is still controversial. To clarify the action and mechanism of ketamine upon cardiovascular system, arterial blood pressure, tension of aortic ring, left ventricular developed pressure and heart rate were measured in rats, Ketamine produced two types of effects on arterial blood pressure in anesthetized rats; monophasic effect (blood pressure lowering) and biphasic effect (initial transient blood pressure increasing following sustained lowering), The ketamine-induced lowering of aterial blood pressure showed a concentration-dependent manner, inhibited by the pretreament of $MgCl_2$ and potentiated by the pretreatment of $CaCl_2$. The ketamine-induced lowering of aterial blood pressure was suppressed by the pretreatment of nifedipine, verapamil or lidocaine. In phenylephrine-precontracted endothelium intact (+E) aortic rings, ketamine sometimes caused a small enhancement of contraction ($112.5{\pm}3.6{\%}$). However, in many experiments, ketamine produced a concentration-dependent relaxation in +E aortic rings precontracted with either phenylephrine or KCl. Ketamine-induced relaxation was significantly greater in KCl-precontracted strips than phenylephrine-precontracted strips. In phenylephrine-precontracted +E aortic rings, the ketamine-induced vasorelaxation was not suppressed by endothelium removal or by the pretreatment of a nitric oxide synthase inhibitors, L-$N^G$-nitro-arginine and a guanylate cyclase inhibitors, methylene blue, suggesting that the ketamine-induced vasorelaxation is not dependent on the endothelial function. In addition, ketamine elicited an increase in left ventricular developed pressure in perfused hearts accompanied by decrease in heart rate. These results suggest that ketamine could evoke a hypotension due to vasorelaxation and decrease in heart rate in rats. The inhibitory effect of cardiovascular system might be associated with modulation of $Ca^{2+}$ homeostasis.

• Molecules and Cells
• /
• v.24 no.2
• /
• pp.283-287
• /
• 2007

$TGF-{\beta}1$ induces Ig germ-line ${\alpha}$ ($GL{\alpha}$) transcription and subsequent class switching recombination (CSR) to IgA. In the present study, we investigated the roles of two E3-ubiquitin ligases, Smurfs (HECT type) and Arkadia (RING finger type) on $TGF{\beta}1$-induced IgA CSR. We found that over-expression of Smurf1 and Smurf2 decreased $TGF{\beta}1$-induced $GL{\alpha}$ promoter activity and strengthened the inhibitory effect of Smad7 on the promoter activity. Further, over-expression of Smurf1 and Smurf2 decreased both Smad3/4-mediated and Runx3-mediated $GL{\alpha}$ promoter activities, suggesting that the Smurfs can down-regulate the major $TGF-{\beta}1$ signaling pathway and decrease $GL{\alpha}$ gene expression. In parallel, the over-expressed Smurf1 decreased the expression of endogenous IgA CSR-predictive transcripts ($GLT_{\alpha}$, $PST_{\alpha}$, and $CT_{\alpha}$) and also $TGF{\beta}1$-induced IgA secretion. Conversely over-expression of Arkadia abolished the inhibitory effect of Smad7 on $TGF{\beta}1$-induced $GLT_{\alpha}$ expression and IgA secretion. Similar results were obtained in the presence of over-expressed Smad7 and Smurf1. These results indicate that Arkadia can amplify $TGF{\beta}1$-induced IgA CSR by degrading Smad7, which interacts with Smurf1. We conclude that Smurf and Arkadia have opposite roles in the regulation of $TGF{\beta}1$-induced IgA isotype expression.

• Journal of the Korean Chemical Society
• /
• v.41 no.2
• /
• pp.69-76
• /
• 1997

Kinetic studies for the nucleophilic substitution reactions of the benzoic anhydrides with anilines in methanol-acetonitrile mixtures at$35.0{\circ}C$have been carried out in order to elucidate the reaction mechanism. Individual rate constants$k_{XY}$and$k_{XZ}$were decided from the ratios of the reaction products for the competitive substitution reaction at either one of the two carbonyl carbons in benzoic anhydride. Transition state structure and reaction mechanism were elucidated by the Hammett$p_x,\;p_y$and$p_z$values and cross interaction constant$p_x\;p_y$and$p_zvalues. The reaction of the benzoic anhydride has been proposed to proceed by a frontside attack$S_N2 $mechanism with four-membered ring transition state from unusually large magnitude of the$ρ_X,\;ρ_{XY},\;ρ_{XZ}$and positive$p_Y$values.