• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.396-397
• /
• 2011

This paper has proposed a multi-channel low pass filter (LPF) for LTE-Advanced systems. The proposed LPF is an active-RC 5th chebyshev topology with three cut-off frequencies of 5 MHz, 10 MHz, and 40 MHz. A 3-bit tuning circuit has been adopted to prevent variations of each cut-off frequency from process, voltage, and temperature (PVT). To achieve a high cut-off frequency of 40 MHz, an operational amplifier used in the proposed filter has employed a PMOS cross-connection load with a negative impedance. A proposed filter has been implemented in a $0.13-{\mu}m$ CMOS technology and consumes 20.2 mW with a 1.2V supply voltage.

• Journal of Navigation and Port Research
• /
• v.31 no.10
• /
• pp.865-868
• /
• 2007

Recently, wireless LANs are often applied in home or office because of its various of convenience. Frequency range of wireless LANs specified by IEEE 802.11b is at 2.4 GHz. The bluetooth, the microwave oven, and the PDA(Personal Digital Assistants) uses, however, the same frequency band. So problems will be produced in these environments, such as multi-pass interference and system-to-system interference. These problems can be eliminated by using EM wave absorber. In this paper, we designed and fabricated EM wave absorber using MnZn-Ferrite, Sendust, and CPE( Chlorinated Polyethylene). The EM wave absorber with the ratio of material (MnZn-Ferrite : Sendust : CPE = 64 : 16 : 20 wt.%) has thickness of 3.7 mm and absorption ability more than 17 dB at 2.4 GHz.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.12
• /
• pp.1810-1814
• /
• 2017

This paper develops an approach to the algorithm of Gait pattern Analysis and step measurement with Multi-Pressure Sensors. The process of gait consists of 8 steps including stance and swing phase. As 3 parts of foot is supporting most of human weight, multiple pressure sensors are attached on the parts of foot: forefoot, big toe, heel. As 3 parts of foot is supporting most of human weight, multiple pressure sensors are attached on the parts of foot: forefoot, big toe, heel. normal gait proceed from heel, forefoot and big toe over time. While normal gait proceeds, values of heel, forefoot and big toe can be changed over time. So Each values of pressure sensors over time could discriminate whether it is normal or abnormal gait. Measuring Device consists of non-inverting amplifiers and low pass filter. Through timetable of values, normal gait pattern can be analyzed, because of supported weight of foot. Also, the peak value of pressure can judge whether it is walking or running. While people are running, insole of shoes is floating in the air on moment. Using this algorithm, gait analysis and step count can be measured.

• Journal of Welding and Joining
• /
• v.27 no.6
• /
• pp.31-35
• /
• 2009

When conducting CTOD test, especially in thick welded steel plate, fatigue pre-cracking occasionally failed to satisfy the requirements of standards thus making the test result invalid. Internally accumulated residual stress of test piece has been thought as one of the main reasons. The propagation of fatigue crack, started from the tip of machined notch, which might have propagated irregularly due to residual stress field. To overcome this kind of difficulty three methods to modify the residual stress are suggested in standard i.e. local compression, reverse bending and stepwise high-R ratio method. In this paper not only multi pass welding but also local pre-compressing process of thick steel plate has been simulated using finite element method for clarifying variation of internal welding residual stress. The simulated results show that welding residual stress is compressive in the middle section of the model and it is predominantly increased after machining the specimen. Comparing as-welded state all component of the welding residual stress changing to compressive in the tip of machine notch whereas residual stress of the outer area remain as tensile condition relatively. Analysis results also show that this irregular residual stress distribution is improved to be more uniformly by applying local compression.

• Journal of Welding and Joining
• /
• v.31 no.6
• /
• pp.84-89
• /
• 2013

The demand of LNG tank and the constituting material, i.e., the Al5083 thick plate, increased due to the rapid growth LNG market. To weld the Al5083 thick plate, the gas metal arc welding (GMAW) of high current is necessary to increase manufacturing productivity incurred by the multi pass welding. However, the arc welding vaporizes the volatile element such as magnesium (Mg). This phenomenon changes the Mg composition of the weld metal and the mechanical properties. The study investigated the weldability of Al5083 alloys after conducting high current GMAW. The Al5083 alloy was welded by using different size of welding wires and high current (800-950A). As the arc current increased from 800A to 950A, the mechanical strength decreased and the secondary dendrite arm spacing (SDAS) increased. Even though the arc current increased SDAS, the mechanical strength decreased due to the Mg loss in the weldment. The large diameter of welding wire decreased the dilution of the weld, therefore increasing the Mg content and the strength of the weld. For the reason, the content of Mg in welds was a major parameter to determine the mechanical property for the high current GMAW. For the arc current between 800A and 950A, the yield strength of the weldments showed a relationship with the weight percent of Mg content ($X_{Mg}$): Y.S = 27.9($X_{Mg}$)-11.

• Transactions of Materials Processing
• /
• v.30 no.6
• /
• pp.306-310
• /
• 2021

In this study, IF steel, which has a body-centered cubic (BCC) crystal structure, was fabricated as a 25 mm-long cube, and then processed for one cycle without intermediate heat treatment by applying MADF Ver.1 and Ver.2 processes. MADF processing was performed with graphite lubrication for each pass at room temperature. The development of the microstructure and texture was analyzed and compared by the location of the specimen using EBSD measurements of the IF steel. Vickers hardness test and miniature tensile test were also performed to analyze the mechanical properties. The coarse grain size of 742.6 ㎛ of the as-received IF steel was refined to a grain size of 53.0 ㎛ after one cycle of MADF Ver.1 processing and 27.0 ㎛ after MADF Ver.2 processing. Vicker's hardness of the as-received IF steel at 94 Hv was increased to 185.6 Hv and 191.2 Hv after one cycle of MADF Ver.1 and Ver.2 processing, respectively.

• Journal of Information Technology Services
• /
• v.20 no.6
• /
• pp.45-62
• /
• 2021

After the COVID-19 outbreak in 2019, the spread of COVID-19 has not been easily caught despite preventive measures in each country. The spread of COVID-19 has hit the world, especially in the economic and tourism sectors. Countries around the world are easing restrictions on the movement of vaccinated people in preparation for the post-corona era. Under the name of "Vaccine Passport," "Vaccination Certificate," and "Digital Health Pass," vaccination measures are being implemented to allow vaccination recipients to use multi-use facilities. However, there is no international agreement on the movement of countries, and each country has its own immigration policy. In order to return to pre-corona daily life, global agreements must be reached from the movement of vaccinated people between countries, and standards and implementation methods must be determined. This study focuses on the implementation and utilization of vaccination certificates suitable for the COVID-19 era. We will look at the spread of COVID-19 and its international response policies. In the case of COVID-19, we will investigate why vaccination certificate installation should be standardized and how far the current standardization has been discussed, and discuss the characteristics of vaccination certificate installation and considerations. In order for the immunization certificate discussed in the previous chapter to be recognized internationally, institutional and technical considerations are identified and security factors that may occur in each implementation are also presented. Finally, the international recognition case of vaccination certificate is discussed, and the method of installation and utilization of vaccination certificate is proposed. This paper can be used as a policy because of its timeliness in studying the standards of vaccination certificates and considerations for international recognition to restore movement between countries in the spread of COVID-19. In addition, if other infectious diseases occur in the future or similar cases where movement between countries is restricted, it can be used as a reference to support the movement of verified people.

• Journal of Korea Society of Industrial Information Systems
• /
• v.24 no.2
• /
• pp.1-14
• /
• 2019

Since most documents used in web, XML, office applications are tree-structured, diff, merge, and version control for tree-structured documents in multi-user environments are crucial tasks. However research on edit scripts which is a basis for them is in primitive stage. In this paper, we present a document model for understanding the change of tree-structured documents as edit scripts are executed, and propose a method of switching adjacent edit operations on tree-structured documents based on the analysis of the effects of edit operations. Mostly, edit scripts which are produced as the results of diff on tree-structured documents only consist of basic operations such as update, insert, delete. However, when move and copy are included in edit scripts, because of the characteristics of their complex operation, it is often that edit scripts are generated to execute in two passes. In this paper, using the proposed method of switching edit operations, we present an algorithm of transforming the edit scripts of X-treeESgen, which are designed to execute in two passes, into the ones that can be executed in one pass.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.10a
• /
• pp.813-815
• /
• 2016

This paper implements a device control system based on the brain wave data. Brain-Computer Interface (BCI) technology can pass directly to the system without going through the operation of the language or body. By controlling the device to detect brain waves in real time according to the change of status it helps to ease life for a variety of services, such as disabled people with limited mobility or students, people who need multi-tasking. In addition, it is possible to develop an application service such as the home device control system. A device control system implemented in the paper based on the data collected from the EEG Headset associated to control the power of the smart phone and audio. Control the power ON / OFF operation by the Attention, and support service functions to control the audio by the Meditation and Eye blink. It was confirmed that the device control using the brain wave data to be operated through a laboratory test successfully.

• Korean Journal of Materials Research
• /
• v.29 no.6
• /
• pp.392-397
• /
• 2019

A cold roll-bonding process is applied to fabricate an AA6061/AA5052/AA6061 three-layer clad sheet. Two AA6061 and one AA5052 sheets of 2 mm thickness, 40 mm width, and 300 mm length are stacked, with the AA5052 sheet located in the center. After surface treatment such as degreasing and wire brushing, sample is reduced to a thickness of 1.5 mm by multi-pass cold rolling. The rolling is performed at ambient temperature without lubricant using a 2-high mill with a roll diameter of 400 mm at rolling speed of 6.0 m/sec. The roll bonded AA6061/AA5052/AA6061 complex sheet is then hardened by natural aging(T4) and artificial aging(T6) treatments. The microstructures of the as-roll bonded and age-hardened Al complex sheets are revealed by optical microscopy; the mechanical properties are investigated by tensile testing and hardness testing. After rolling, the roll-bonded AA6061/AA5052/AA6061 sheets show a typical deformation structure in which grains are elongated in the rolling direction. However, after T4 and T6 aging treatment, there is a recrystallization structure consisting of coarse equiaxed grains in both AA5052 and AA6061 sheets. The as roll-bonded specimen shows a sandwich structure in which an AA5052 sheet is inserted into two AA6061 sheets with higher hardness. However, after T4 and T6 aging treatment, there is a different sandwich structure in which the hardness of the upper and lower layers of the AA6061 sheets is higher than that of the center of the AA5052 sheet. The strength values of the T4 and T6 age-treated specimens are found to increase by 1.3 and 1.4 times, respectively, compared to that value of the starting material.