• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제54권2호
• /
• pp.53-59
• /
• 2005

In this paper, optimum shape design of permanent magnet in slotted type Permanent Magnet Linear Synchronous Motor(PMLSM) is progressed for minimization of detent force owing to structure of slot-teeth and thrust ripple by harmonic magnetic flux of permanent magnet. In order to reduce remodeling time as changing design parameter for Permanent Magnet shape optimization, the moving model node technique was applied. The characteristics of thrust and detent force computed by finite element analysis are acquired equal effect both skewed basic model and optimum model which is optimization of permanent magnet shape. In addition to, thrust per unit volume is improved 4.l2[%] in optimum model.

• 한국정밀공학회지
• /
• 제19권7호
• /
• pp.36-42
• /
• 2002

This paper presents two actuators for levitation using repulsions of permanent magnet and two magnetic levitation tables using the actuators. Here, one actuator for levitation consists of one fixed magnet and one moving magnet, and the other actuator consists of two fixed magnets and one moving magnet. The moving part of the magnetic levitation table contains the moving magnets. repulsive forces caused by the permanent magnets are linearized, and then the equation of motion of the moving part of the table is derived. Using the equation of motion, stability conditions of the moving part are deduced. The stability conditions are analyzed for positional relations of the moving magnets and the minimum number of active control required for stable system. As a result, in the each case of magnetic levitation tables, the requirements for stabilization are expressed by the positional relations and the number of the active controls.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제50권2호
• /
• pp.53-58
• /
• 2001

This paper describes a moving mesh technique for dynamic characteristics analysis of permanent magnet linear synchronous motor with the secondary aluminium sheet. The moving mesh technique applied to the linear induction motor can be used to analyze the linear synchronous motor with the rectangular permanent magnet. But in case of the permanent magnet with taper, the shape of the permanent magnet is presented. The time-stepped finite element method is used for the dynamic characteristics simulation of the permanent magnet linear synchronous motor, The results of application example(hysteresis current controlled inverter fed control) such as thrust, current and flux plots are shown.

• 한국초전도ㆍ저온공학회논문지
• /
• 제11권1호
• /
• pp.49-54
• /
• 2009

This paper presents the numerical simulation results on the moving type electrodynamic suspension (EDS) simulator and static type EDS simulator using high-Tc superconducting (HTS) levitation magnet. The levitation force of the EDS system is formed by the reaction between the moving magnet and the fixed ground conductor. The possible two ways to simulate the EDS system were simulated in this paper by using finite element method (FEM). The first way was the moving type simulator which consists of the fixed HTS magnet and the moving ground conductor. The second way was the static type simulator which consists of the fixed magnet, the fixed ground conductor and the ac current supply system. To verify the characteristics of high speed EDS system with the moving type simulator heavy, large and fast moving ground conductor is needed. The static type simulator can get the characteristics of the high speed EDS system by applying equivalent ac current to velocity, therefore it does not need large moving part. The static type EDS simulator, which can consist of an HTS magnet, the fixed ground conductor(s), an AC power supply and the measuring devices, also test the effect of the shape of the ground conductor easily. The plate type ground conductor made stronger levitation force than ring type ground conductor. Although the outer diameter 335 mm ring type ground conductor (Ring3) was larger than the outer diameter 235 mm ground conductor (Ring2), the levitation force by Ring2 was stronger than that by Ring3. From the calculation results on this paper, the consideration of the magnetic flux distribution according to the levitation height should be included in the process of the ground conductor design.

• 한국소음진동공학회논문집
• /
• 제14권12호
• /
• pp.1255-1260
• /
• 2004

A moving-magnet type pickup actuator has an assembly error. That is, the actuating Part of an actuator is shifted from initial position after we assemble it into yoke. This Is the result of an effect of magnetic force between magnet and yoke. We performed magnetic-analysis using FEA. As a result of simulation, we improved the assembling efficiency for moving-magnet type actuator.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.356-361
• /
• 2004

가동자석형 픽업 구동기를 조립하는 경우 조립 전후에 오차가 발생하게 된다. 즉, 렌즈홀더 와 스프링홀더 A'SSY 를 요크에 조립하기 전자 후에 렌즈홀더가 shift 된 양을 살펴보면 상당한 편차가 있음을 볼 수 있다. 이것은 자석 중심과 요크 중심이 어긋날 경우 자석과 요크 사이에 발생하는 자기력의 영향으로 발생하는 것으로, 자기해석을 수행한 결과 자석과 요크의 크기에 따라 자기력의 영향이 달라짐을 확인할 수 있었고, 개발모델에 적용하여 조립성능이 향상됨을 확인할 수 있었다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.1033-1036
• /
• 2007

The optical disc drive has used a high NA objective lens and a shorter wavelength laser diode for high recording density. But high NA and shorter wavelength cause several margins to become short. Focusing and tracking servo has to be more accurate and active tilt compensation mechanism is also needed for coma aberration compensation. In this paper, we proposed 3-axis moving magnet type actuator. For 3-DOF motion, moving coil actuator has to equip 6 wires for supplying 3 independent signals. However, moving magnet type actuator doesn't need to change the configuration of wires because coils are in stator. So, we added tilting mechanism to 2-axis moving magnet actuator which is designed in previous research. Addition of the tilting mechanism cuts down the focusing sensitivity. So, maximization the tilting sensitivity and securing the focusing sensitivity are objectivities of this research. DOE (design of experiments) procedures of electromagnetic circuit are performed for parameter study and the optimization is also performed to maximize the tilt sensitivity. And then the final design is suggested and its performance is verified by FE simulation.

• 정보저장시스템학회논문집
• /
• 제3권4호
• /
• pp.191-195
• /
• 2007

The optical disc drive has used a high NA objective lens and a shorter wavelength laser diode for high recording density. But high NA and shorter wavelength cause several margins to become short. Focusing and tracking servo has to be more accurate and active tilt compensation mechanism is also needed for coma aberration compensation. In this paper, we proposed 3-axis moving magnet type actuator. For 3-DOF motion, moving coil actuator has to be equipped with 6 wires for supplying 3 independent signals. However, moving magnet type actuator doesn't need to change the configuration of wires because coils are in stator. So, we added a tilt mechanism to the 2-axis moving magnet actuator which is designed in previous research. Addition of the tilt mechanism cuts down the focus sensitivity. So, maximization the tilting sensitivity and securing the focusing sensitivity are objectivities of this research. DOE (design of experiments) procedures of electromagnetic circuit are performed for parameter study and the optimization is also performed to maximize the tilt sensitivity. And then the final design is suggested and its performance is verified by FE simulation.

• 정보저장시스템학회논문집
• /
• 제4권1호
• /
• pp.23-28
• /
• 2008

In this paper we suggested the moving magnet type actuator for optical disc drive which has high frequency of flexible mode. Generally, moving magnet type actuator has the advantage for increase the frequency of flexible mode. But it has low driving sensitivity due to the weight of its moving part. To overcome this shortcoming, we designed the model with the closed electromagnetic circuit for tracking direction. In addition, we improved the driving sensitivity and frequency of flexible mode by using of DOE (design of experiment) procedure for EM circuit. Consequently, it is verified that final designed model satisfied with the desired specifications.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제55권1호
• /
• pp.21-26
• /
• 2006

This paper deals with the dynamic analysis and experiments of moving-magnet linear actuator with/without spring. On the basis of two dimensional (2-D) analytical solutions and experiments, control parameters such as thrust constant, back-emf constant, inductance and resistance are obtained. And then, dynamic simulation algorithm is established from the voltage and motion equation. Finally, for various values of frequency, dynamic simulation results for characteristics of current and displacement of moving-magnet linear actuator with and without spring are presented and confirmed through the experiments. In particular, This paper applies the PWM voltage waveform obtained from a DSP for bidirectional voltage drive to the actuator.