• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05a
• /
• pp.94-97
• /
• 2006

This paper reports fatigue test results of 1/3 scaled PSC slab models using moving wheel loading machine. The purpose of the test is to improve the fatigue formulas by comparing the existing formulas with the test results. Based on the result, improved fatigue formula is proposed for the PSC slab.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.6
• /
• pp.487-491
• /
• 2008

Tuning of the speed controller in the linear servo applications needs the accurate information of a mover mass including a load mass. Therefore this paper proposes the mass estimation method of a permanent magnet linear synchronous motor(PMLSM) applied at the vertical axis by using the recursive Least-Squares estimation algorithm. First, this paper derives the deterministic autoregressive moving average(DARMA) model of the mechanical dynamic system used at the vertical axis. The application of the Least-Squares algorithm to the derived DARMA model gives the mass estimation method. Matlab/Simulink-based simulation and experimental results show that the total mover mass of a PMLSM applied at the vertical axis can be accurately estimated at both no-load and load conditions.

• Journal of Ocean Engineering and Technology
• /
• v.21 no.6
• /
• pp.42-46
• /
• 2007

The impact of a single wave generated by a dam break with a tall structure is modeled with a three-dimensional version of the Moving particle semi-implicit (MPS) method. The particle method is more feasible and effective than methods based on grid connection problems involving violent free surface motions. In the present study, the Tsunami impact load and the change of longitudinal velocity component around the structure, which are obtained from the numerical simulation, are compared to those from experiments.

• Smart Structures and Systems
• /
• v.24 no.5
• /
• pp.617-630
• /
• 2019

Currently most of the vision-based structural identification research focus either on structural input (vehicle location) estimation or on structural output (structural displacement and strain responses) estimation. The structural condition assessment at global level just with the vision-based structural output cannot give a normalized response irrespective of the type and/or load configurations of the vehicles. Combining the vision-based structural input and the structural output from non-contact sensors overcomes the disadvantage given above, while reducing cost, time, labor force including cable wiring work. In conventional traffic monitoring, sometimes traffic closure is essential for bridge structures, which may cause other severe problems such as traffic jams and accidents. In this study, a completely non-contact structural identification system is proposed, and the system mainly targets the identification of bridge unit influence line (UIL) under operational traffic. Both the structural input (vehicle location information) and output (displacement responses) are obtained by only using cameras and computer vision techniques. Multiple cameras are synchronized by audio signal pattern recognition. The proposed system is verified with a laboratory experiment on a scaled bridge model under a small moving truck load and a field application on a footbridge on campus under a moving golf cart load. The UILs are successfully identified in both bridge cases. The pedestrian loads are also estimated with the extracted UIL and the predicted weights of pedestrians are observed to be in acceptable ranges.

• Structural Engineering and Mechanics
• /
• v.6 no.6
• /
• pp.673-691
• /
• 1998

In this paper, an analytic method to examine the random vibration of multispan Timoshenko frames due to a concentrated load traversing at a constant velocity is presented. A load's magnitude is a stationary process in time with a constant mean value and a variance. Two types of variances of this load are considered: white noise process and cosine process. The effects of both velocity and statistical characteristics of load and span number of the frame on both the mean value and variance of deflection and moment of the structure are investigated. Results obtained from a multispan Timoshenko frame are compared with those of a multispan Bernoulli-Euler frame.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.1
• /
• pp.137-144
• /
• 1998

For a model system consisted of four pneumatic cylinders with strokes of 10, 20, 40 and 80 mm, investigation was carried out experimentally and numerically about the reliability of system with elastic and viscous load. The elastic load affects the performance of each cylinder in cylinder series, and changes the time lag and the velocity of the piston which makes the positioning control rather difficult. Taking the effects of the elastic load into consideration, positioning can be carried out comparatively smoothly by only adjusting the driving timing. The effect of a viscous load reduces the vibration of each moving body in the cylinder series and also reduces the over-travelled distance which happens when several cylinders move at the same time. For reasons, a positioning with a viscous load can be relatively smoothly carried out even without the timing control.

• Proceedings of the KIEE Conference
• /
• 2002.11b
• /
• pp.209-211
• /
• 2002

This paper computes the regional, seasonal and hourly representative model of load power factor considering load characteristics of all 154/22.9 kV substations. An accurately computed representative model of load power factor is studied to present a precision improvement of power system analysis and the security of the system. The method to compute representative model of load utilizes the method of applicable moving average based on the method of flow average. The EMS data are used as the source to assess the load power factor.

• Proceedings of the KIEE Conference
• /
• 2003.07d
• /
• pp.2227-2229
• /
• 2003

Using the gyro effect, Balance Beam Controller is developed with Samsung Corporation. Balance Beam Controller is possible to control the position of an object in air by controlling the attitude of inner gimbal. But in the unknown load inertia case, even a skilled worker it is not easy to operate a Balance Beam. That is caused by the difficulty to estimate the load inertia. If the amount of the gimbal operation is set excessively with a wrong load estimation, it can often cause accidents. To solve this problem, the control function which is revolving with velocity of the revolution has to be added to developed equipment. In this research, we analyze the characteristics of a Balance Beam(the smaller load inertia, the bigger force of restitution) using the angular velocity sensor, and present constant velocity revolving controller with estimating value of the load using this moving characteristics.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.1
• /
• pp.769-777
• /
• 2015

In this paper, a damage assessment technique using a moving load test and optical sensors was studied to overcome the deficiency of measurement information in bridge maintenance. Continuous displacements by applying the reciprocal theorem to the test can make the assessment simpler and more practical. Numerical and experimental studies were performed to show the efficiency and accuracy of the proposed technique as well as the possibility of a more realistic assessment for large infrastructure. The results showed that the assessed damage levels are quite accurate, and similar to the exact values in actual damage locations, even in the experiments. The proposed technique is useful and practical for both detecting damage locations and damage quantities.

• Journal of the Korean Society for Railway
• /
• v.16 no.4
• /
• pp.286-297
• /
• 2013

In this paper we evaluated dynamic stability, considering the effects of modeling and analysis methods on moving load analysis, for which a sophisticated 3 dimensional model of a PSC-I type girder bridge was used. For this purpose, we suggested a reasonable modeling method and the physical properties of the concrete and ballasted track system involved. We also analyzed the response characteristics according to: 1) the type of track system; 2) whether or not the track was modeled; 3) whether or not the distance between the girder center and the bearing were considered; 4) the analysis method (i.e., direct integral and modal analysis); 5) whether or not the frequency was filtered.